lkml.org 
[lkml]   [2018]   [Sep]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v3 2/2] phy: zynqmp: Add dt bindings for ZynqMP phy
Date
Hi Rob,

Thanks a lot for reviewing this code, please find my comments inline

>> +This binding describes a ZynqMP PHY device that is used to control
>> +ZynqMP High Speed Gigabit Transceiver(GT). ZynqMP PS GTR provides
>> +four lanes and are used by USB, SATA, PCIE, Display port and Ethernet SGMMI
>controllers.
>> +
>> +Phy provider node
>> +=================
>> +
>> +Required properties:
>> +- compatible : Can be "xlnx,zynqmp-psgtr-v1.1" or "xlnx,zynqmp-psgtr"
>> +
>> +- reg : Address and length of register sets for each device in
>> + "reg-names"
>> +
>> +- reg-names : The names of the register addresses corresponding to the
>> + registers filled in "reg":
>> + - serdes: SERDES block register set
>> + - siou: SIOU block register set
>> +
>> +Optional properties:
>> +- xlnx,tx_termination_fix : Include this for fixing functional issue
>> +with the
>
>s/_/-/
>

Will fix this in next series of the patch

>> + TX termination resistance in GT, which can be out of spec for
>> + the XCZU9EG silicon version. This property is not required for
>> + "xlnx,zynqmp-psgtr-v1.1"
>> +
>> +Required nodes : A sub-node is required for each lane the controller
>> + provides.
>> +
>> +Phy sub-nodes
>> +=============
>> +
>> +Required properties:
>> +lane0:
>
>lane0 or lane@0? If you need or care about numbering then add a reg property.
>

Thanks for correcting, Will change this to lane@0 and resend the patches

>> +- #phy-cells : Should be 4
>> +
>> +lane1:
>> +- #phy-cells : Should be 4
>> +
>> +lane2:
>> +- #phy-cells : Should be 4
>> +
>> +lane3:
>> +- #phy-cells : Should be 4
>> +
>> +Example:
>> + zynqmp_phy: phy@fd400000 {
>> + compatible = "xlnx,zynqmp-psgtr-v1.1";
>> + status = "okay";
>> + reg = <0x0 0xfd400000 0x0 0x40000>, <0x0 0xfd3d0000 0x0 0x1000>;
>> + reg-names = "serdes", "siou";
>> +
>> + lane0: lane@0 {
>> + #phy-cells = <4>;
>> + };
>> + lane1: lane@1 {
>> + #phy-cells = <4>;
>> + };
>> + lane2: lane@2 {
>> + #phy-cells = <4>;
>> + };
>> + lane3: lane@3 {
>> + #phy-cells = <4>;
>> + };
>> + };
>> +
>> +Specifying phy control of devices
>> +=================================
>> +
>> +Device nodes should specify the configuration required in their "phys"
>> +property, containing a phandle to the phy port node and a device type.
>> +
>> +phys = <PHANDLE CONTROLLER_TYPE CONTROLLER_INSTANCE LANE_NUM
>> +LANE_FREQ>;
>> +
>> +PHANDLE = &lane0 or &lane1 or &lane2 or &lane3
>> +CONTROLLER_TYPE = PHY_TYPE_PCIE or PHY_TYPE_SATA or PHY_TYPE_USB
>> + or PHY_TYPE_DP or PHY_TYPE_SGMII
>> +CONTROLLER_INSTANCE = Depends on controller type used, can be any of
>> + PHY_TYPE_PCIE : 0 or 1 or 2 or 3
>> + PHY_TYPE_SATA : 0 or 1
>> + PHY_TYPE_USB : 0 or 1
>> + PHY_TYPE_DP : 0 or 1
>> + PHY_TYPE_SGMII: 0 or 1 or 2 or 3
>> +LANE_NUM = Depends on which lane clock is used as ref clk, can be
>> + 0 or 1 or 2 or 3
>
>I'm not really clear about what this is.
>

ZynqMP phy has a feature that each individual lane (among the 4 lanes) can have its own PLL
reference clock or share the clock generated from other lanes. For example

Lane 0 can use its own ref clock for PLL: in this case LANE_NUM = 0
Lane0 can use Lane 3's ref clock for PLL: in this case LANE_NUM = 3

Maybe I should change the name LANE_NUM to LANE_REF_CLK to give more readability. Please
correct me if wrong.

>> +LANE_FREQ = Frequency that controller can operate, can be any of
>> +
>19.2Mhz,20Mhz,24Mhz,26Mhz,27Mhz,28.4Mhz,40Mhz,52Mhz,
>> + 100Mhz,108Mhz,125Mhz,135Mhz,150Mhz
>
>This can't be implied by the mode/type? I wouldn't expect any frequency can be used
>for each mode.
>

Yes you are correct, not all frequencies are supported by all protocols, but each protocol supports
a limited set of multiple reference clock frequencies. For example USB3.0 protocol can operate with
26, 52 & 100 MHZ. Providing any other frequency would make the phy fail to lock the PLL and error
would be generated by the driver. As you suggested, I will add more details regarding the frequencies
supported by different protocols in the next series of the patch.

>> +
>> +Example:
>> +
>> +#include <dt-bindings/phy/phy.h>
>> +
>> + usb@fe200000 {
>> + ...
>> + phys = <&lane2 PHY_TYPE_USB3 0 2 2600000>;
>> + ...
>> + };
>> +
>> + ahci@fd0c0000 {
>> + ...
>> + phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
>> + ...
>> + };
>
>What if you are doing multiple lanes for 1 device? That would be more useful 2nd
>example if that's supported.
>

Will add the multi lane example in the next series of the patch.

Thanks,
Anurag Kumar Vulisha

>> --
>> 2.1.1
>>

\
 
 \ /
  Last update: 2018-09-11 10:10    [W:0.228 / U:0.208 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site