lkml.org 
[lkml]   [2018]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH v2] usb: typec: get the vbus source and charge values from the devicetree
Date
From
Hi Heikki

On 2018-09-10 01:35, Heikki Krogerus wrote:
> On Sun, Sep 09, 2018 at 12:05:31PM -0600, Angus Ainslie (Purism) wrote:
>> If the board is being powered by USB disabling the source and sink
>> can remove power from the board. Allow the source and sink to be
>> initallized based on devicetree values.
>>
>> Changed since V1:
>>
>> use devicetree values instead of hardcoded initialization.
>>
>> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
>> ---
>> .../bindings/connector/usb-connector.txt | 4 ++++
>> drivers/usb/typec/tcpm.c | 14
>> +++++++++++---
>> 2 files changed, 15 insertions(+), 3 deletions(-)
>>
>> diff --git
>> a/Documentation/devicetree/bindings/connector/usb-connector.txt
>> b/Documentation/devicetree/bindings/connector/usb-connector.txt
>> index 8855bfcfd778..afe851a713c3 100644
>> --- a/Documentation/devicetree/bindings/connector/usb-connector.txt
>> +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt
>> @@ -22,6 +22,10 @@ Optional properties for usb-c-connector:
>> or Try.SRC, should be "sink" for Try.SNK or "source" for Try.SRC.
>> - data-role: should be one of "host", "device", "dual"(DRD) if typec
>> connector supports USB data.
>> +- init-vbus-source: set the initalization value for vbus-source to
>> true.
>> + If this property is not present the initial value will be false.
>> +- init-vbus-charge: set the initalization value for vbus-charge to
>> true.
>> + If this property is not present the initial value will be false.
>
> If you put the description of those properties here, you are going to
> need to rename them. Those describe tcpm specific properties, but to
> that file you want to put descriptions of generic properties.
>

They are tcpm specific but need to go into the connector sub-node to get
parsed correctly. Would something like below be better ?

diff --git a/Documentation/devicetree/bindings/usb/typec-tcpci.txt
b/Documentation/devicetree/bindings/usb/typec-tcpci.txt
index 0dd1469e7318..ae0a3e97d9b6 100644
--- a/Documentation/devicetree/bindings/usb/typec-tcpci.txt
+++ b/Documentation/devicetree/bindings/usb/typec-tcpci.txt
@@ -15,6 +15,12 @@ Required sub-node:
of connector node are specified in
Documentation/devicetree/bindings/connector/usb-connector.txt

+Optional properties for usb-c-connector sub-node:
+- init-vbus-source: set the initalization value for vbus-source to
true.
+ If this property is not present the initial value will be false.
+- init-vbus-charge: set the initalization value for vbus-charge to
true.
+ If this property is not present the initial value will be false.
+
Example:

ptn5110@50 {

> Your problem is that you can not cope with a lose of VBUS as a sink,
> right? For that you just need one boolean device property IMO.
> Something like depend-on-vbus.

I thought that it would better to be able to control each independently.
With my specific hardware I need both defaulted to true but for another
piece of HW just being able to control one of them might be sufficient.

Thanks
Angus

>
>> Required properties for usb-c-connector with power delivery support:
>> - source-pdos: An array of u32 with each entry providing supported
>> power
>> diff --git a/drivers/usb/typec/tcpm.c b/drivers/usb/typec/tcpm.c
>> index ca7bedb46f7f..7f5d4f209e07 100644
>> --- a/drivers/usb/typec/tcpm.c
>> +++ b/drivers/usb/typec/tcpm.c
>> @@ -2462,9 +2462,7 @@ static int tcpm_init_vbus(struct tcpm_port
>> *port)
>> {
>> int ret;
>>
>> - ret = port->tcpc->set_vbus(port->tcpc, false, false);
>> - port->vbus_source = false;
>> - port->vbus_charge = false;
>> + ret = port->tcpc->set_vbus(port->tcpc, port->vbus_source,
>> port->vbus_charge);
>> return ret;
>> }
>>
>> @@ -4266,6 +4264,16 @@ static int tcpm_fw_get_caps(struct tcpm_port
>> *port,
>> return -EINVAL;
>> port->port_type = port->typec_caps.type;
>>
>> + if (fwnode_property_present(fwnode, "init-vbus-source"))
>> + port->vbus_source = true;
>> + else
>> + port->vbus_source = false;
>> +
>> + if (fwnode_property_present(fwnode, "init-vbus-charge"))
>> + port->vbus_charge = true;
>> + else
>> + port->vbus_charge = false;
>> +
>> if (port->port_type == TYPEC_PORT_SNK)
>> goto sink;
>>
>> --
>> 2.17.1
>
> Thanks,

\
 
 \ /
  Last update: 2018-09-10 15:13    [W:0.088 / U:0.068 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site