lkml.org 
[lkml]   [2018]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/3] ARM: OMAP1: ams-delta: assign MODEM IRQ from GPIO descriptor
Date
Don't request MODEM IRQ GPIO by its global number in
ams_delta_modem_init(). Instead, obtain its GPIO descriptor
and assign related IRQ to the MODEM. Do that from
omap_gpio_deps_init(), where the chip is already looked up. Then, in
ams_delta_modem_init(), just check for the IRQ number having been
already assigned.

Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/mach-omap1/board-ams-delta.c | 47 ++++++++++++++++++++++++++---------
1 file changed, 35 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 34cb63ff45b3..2b90b543c030 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -630,6 +630,28 @@ static struct gpiod_hog ams_delta_gpio_hogs[] = {
{},
};

+static struct plat_serial8250_port ams_delta_modem_ports[];
+
+/*
+ * Obtain MODEM IRQ GPIO descriptor using its hardware pin
+ * number and assign related IRQ number to the MODEM port.
+ * Keep the GPIO descriptor open so nobody steps in.
+ */
+static void __init modem_assign_irq(struct gpio_chip *chip)
+{
+ struct gpio_desc *gpiod;
+
+ gpiod = gpiochip_request_own_desc(chip, AMS_DELTA_GPIO_PIN_MODEM_IRQ,
+ "modem_irq");
+ if (IS_ERR(gpiod)) {
+ pr_err("%s: modem IRQ GPIO request failed (%ld)\n", __func__,
+ PTR_ERR(gpiod));
+ } else {
+ gpiod_direction_input(gpiod);
+ ams_delta_modem_ports[0].irq = gpiod_to_irq(gpiod);
+ }
+}
+
/*
* The purpose of this function is to take care of proper initialization of
* devices and data structures which depend on GPIO lines provided by OMAP GPIO
@@ -649,7 +671,13 @@ static void __init omap_gpio_deps_init(void)
return;
}

+ /*
+ * Start with FIQ initialization as it may have to request
+ * and release successfully each OMAP GPIO pin in turn.
+ */
ams_delta_init_fiq(chip, &ams_delta_serio_device);
+
+ modem_assign_irq(chip);
}

static void __init ams_delta_init(void)
@@ -844,20 +872,18 @@ static int __init modem_nreset_init(void)
}


+/*
+ * This function expects MODEM IRQ number already assigned to the port
+ * and fails if it's not.
+ */
static int __init ams_delta_modem_init(void)
{
int err;

- omap_cfg_reg(M14_1510_GPIO2);
- ams_delta_modem_ports[0].irq =
- gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ if (ams_delta_modem_ports[0].irq < 0)
+ return ams_delta_modem_ports[0].irq;

- err = gpio_request(AMS_DELTA_GPIO_PIN_MODEM_IRQ, "modem");
- if (err) {
- pr_err("Couldn't request gpio pin for modem\n");
- return err;
- }
- gpio_direction_input(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ omap_cfg_reg(M14_1510_GPIO2);

/* Initialize the modem_nreset regulator consumer before use */
modem_priv.regulator = ERR_PTR(-ENODEV);
@@ -866,8 +892,6 @@ static int __init ams_delta_modem_init(void)
AMS_DELTA_LATCH2_MODEM_CODEC);

err = platform_device_register(&ams_delta_modem_device);
- if (err)
- gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);

return err;
}
@@ -898,7 +922,6 @@ static int __init late_init(void)

unregister:
platform_device_unregister(&ams_delta_modem_device);
- gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
return err;
}

--
2.16.4
\
 
 \ /
  Last update: 2018-09-10 04:44    [W:0.121 / U:0.380 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site