lkml.org 
[lkml]   [2018]   [Aug]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 3/3] mmc: sdhci-of-dwcmshc: solve 128MB DMA boundary limitation
On Tue, 28 Aug 2018 10:51:02 +0300 Adrian Hunter wrote:

> On 27/08/18 11:24, Jisheng Zhang wrote:
> > When using DMA, if the DMA addr spans 128MB boundary, we have to split
> > the DMA transfer into two so that each one doesn't exceed the boundary.
> >
> > Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
> > ---
> > drivers/mmc/host/sdhci-of-dwcmshc.c | 41 +++++++++++++++++++++++++++++
> > 1 file changed, 41 insertions(+)
> >
> > diff --git a/drivers/mmc/host/sdhci-of-dwcmshc.c b/drivers/mmc/host/sdhci-of-dwcmshc.c
> > index 1b7cd144fb01..cfbdae8703a1 100644
> > --- a/drivers/mmc/host/sdhci-of-dwcmshc.c
> > +++ b/drivers/mmc/host/sdhci-of-dwcmshc.c
> > @@ -8,21 +8,50 @@
> > */
> >
> > #include <linux/clk.h>
> > +#include <linux/mm.h>
> > #include <linux/module.h>
> > #include <linux/of.h>
> > +#include <linux/sizes.h>
> >
> > #include "sdhci-pltfm.h"
> >
> > +#define BOUNDARY_OK(addr, len) \
> > + ((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1)))
> > +
> > struct dwcmshc_priv {
> > struct clk *bus_clk;
> > };
> >
> > +/*
> > + * If DMA addr spans 128MB boundary, we split the DMA transfer into two
> > + * so that each DMA transfer doesn't exceed the boundary.
> > + */
> > +static void dwcmshc_adma_write_desc(struct sdhci_host *host, void **desc,
> > + dma_addr_t addr, int len, unsigned int cmd)
> > +{
> > + int tmplen, offset;
> > +
> > + if (likely(!len || BOUNDARY_OK(addr, len))) {
> > + sdhci_adma_write_desc(host, desc, addr, len, cmd);
> > + return;
> > + }
> > +
> > + offset = addr & (SZ_128M - 1);
> > + tmplen = SZ_128M - offset;
> > + sdhci_adma_write_desc(host, desc, addr, tmplen, cmd);
> > +
> > + addr += tmplen;
> > + len -= tmplen;
> > + sdhci_adma_write_desc(host, desc, addr, len, cmd);
> > +}
> > +
> > static const struct sdhci_ops sdhci_dwcmshc_ops = {
> > .set_clock = sdhci_set_clock,
> > .set_bus_width = sdhci_set_bus_width,
> > .set_uhs_signaling = sdhci_set_uhs_signaling,
> > .get_max_clock = sdhci_pltfm_clk_get_max_clock,
> > .reset = sdhci_reset,
> > + .adma_write_desc = dwcmshc_adma_write_desc,
> > };
> >
> > static const struct sdhci_pltfm_data sdhci_dwcmshc_pdata = {
> > @@ -36,12 +65,24 @@ static int dwcmshc_probe(struct platform_device *pdev)
> > struct sdhci_host *host;
> > struct dwcmshc_priv *priv;
> > int err;
> > + u32 extra;
> >
> > host = sdhci_pltfm_init(pdev, &sdhci_dwcmshc_pdata,
> > sizeof(struct dwcmshc_priv));
> > if (IS_ERR(host))
> > return PTR_ERR(host);
> >
> > + /*
> > + * The DMA table descriptor count is calculated as the maximum
> > + * number of segments times 2, to allow for an alignment
> > + * descriptor for each segment, plus 1 for a nop end descriptor,
> > + * plus extra number for cross 128M boundary handling.
> > + */
> > + extra = DIV_ROUND_UP(totalram_pages, SZ_128M / PAGE_SIZE);
>
> The amount of RAM is not necessarily the same as the highest physical
> address. I think what you really want is max_pfn or max_possible_pfn

oh, yeah! But these two vars are not exported, I have two solutions:

1. use the dma_get_required_mask(), this is what I did in v6

2. always let extra = SDHCI_MAX_SEGS, although we may waste, but the
waste is small -- at most we waste 128*12 = 1536 Byte.

But it seems solution 1 could do its job ;)

Thanks,
Jisheng

>
> > + if (extra > SDHCI_MAX_SEGS)
> > + extra = SDHCI_MAX_SEGS;
> > + host->adma_table_cnt += extra;
> > +
> > pltfm_host = sdhci_priv(host);
> > priv = sdhci_pltfm_priv(pltfm_host);
> >
> >
>

\
 
 \ /
  Last update: 2018-08-28 11:56    [W:0.805 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site