lkml.org 
[lkml]   [2018]   [Aug]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 00/40] Tegra SDHCI add support for HS200 and UHS signaling
From
Date
On 27/08/18 13:26, Adrian Hunter wrote:
> On 27/08/18 13:10, Thierry Reding wrote:
>> On Fri, Aug 10, 2018 at 09:08:02PM +0300, Aapo Vienamo wrote:
>>> Hi all,
>>>
>>> This series implements support for faster signaling modes on Tegra
>>> SDHCI controllers. This series consist of several parts: changes
>>> requried for 1.8 V signaling and pad control, pad calibration, and
>>> tuning. Following earlies patch sets have been merged into this
>>> larger set: "Tegra PMC pinctrl pad configuration", "Tegra SDHCI enable
>>> 1.8 V signaling on Tegar210 and Tegra186", "Tegra SDHCI update the
>>> padautocal procedure". Also the patches for enabling SDHCI tuning
>>> are added.
>>>
>>> Changelog:
>>> v2:
>>> - Fix grammar in PMC device tree bindings docs
>>> - Remove a stray line from tegra sdhci bindings
>>> - Cosmetic changes to PMC pinctrl driver
>>> - Fix a typo in "soc/tegra: pmc: Implement
>>> tegra_io_pad_is_powered()" commit message
>>> - Declare mask and value on the same line in
>>> tegra_io_pad_is_powered()
>>> - Move the call to tegra_sdhci_is_pad_and_regulator_valid() to
>>> inside the if condition in tegra_sdhci_reset()
>>> - Use usleep_range() in tegra_sdhci_configure_cal_pad()
>>> - Move sdhci_writel() out of the enable if-else body in
>>> tegra_sdhci_configure_cal_pad()
>>> - Add a delay before starting polling in
>>> tegra_sdhci_pad_autocalib()
>>> - Use usleep_range() in tegra_sdhci_set_tap()
>>> - Rename orig_enabled to status in
>>> tegra_sdhci_configure_card_clk()
>>> - Fix if condition wrapping alignment in tegra_sdhci_set_tap()
>>>
>>> v1:
>>> - Probe the regulator voltage capabilities to determine whether pinctrl
>>> is needed in tegra_sdhci_r eset
>>> - Don't remove tegra_sdhci_voltage_switch()
>>> - Use dev_warn() in tegra_sdhci_init_pinctrl_info()
>>> - Don't change start_signal_voltage_switch callback if pinctrl info
>>> invalid
>>> - Only call udelay(1) on enable in tegra_sdhci_configure_cal_pad()
>>> - Add nvidia, prefix to pad autocal offset dt props in the example
>>>
>>> See the original patch sets for earlier changelogs.
>>>
>>> Aapo Vienamo (40):
>>> dt-bindings: Add Tegra PMC pad configuration bindings
>>> dt-bindings: mmc: tegra: Add pad voltage control properties
>>> dt-bindings: Add Tegra SDHCI pad pdpu offset bindings
>>> dt-bindings: mmc: Add Tegra SDHCI sampling trimmer values
>>> soc/tegra: pmc: Fix pad voltage configuration for Tegra186
>>> soc/tegra: pmc: Factor out DPD register bit calculation
>>> soc/tegra: pmc: Implement tegra_io_pad_is_powered()
>>> soc/tegra: pmc: Use X macro to generate IO pad tables
>>> soc/tegra: pmc: Remove public pad voltage APIs
>>> soc/tegra: pmc: Implement pad configuration via pinctrl
>>> mmc: sdhci: Add a quirk to skip clearing the transfer mode register on
>>> tuning
>>> mmc: tegra: Reconfigure pad voltages during voltage switching
>>> mmc: tegra: Poll for calibration completion
>>> mmc: tegra: Set calibration pad voltage reference
>>> mmc: tegra: Power on the calibration pad
>>> mmc: tegra: Disable card clock during pad calibration
>>> mmc: tegra: Program pad autocal offsets from dt
>>> mmc: tegra: Perform pad calibration after voltage switch
>>> mmc: tegra: Enable pad calibration on Tegra210 and Tegra186
>>> mmc: tegra: Add a workaround for tap value change glitch
>>> mmc: tegra: Parse default trim and tap from dt
>>> mmc: tegra: Configure default tap values
>>> mmc: tegra: Configure default trim value on reset
>>> mmc: tegra: Use standard SDHCI tuning on Tegra210 and Tegra186
>>> mmc: sdhci: Add a quirk to disable card clock during tuning
>>> mmc: tegra: Enable workaround for tuning transfer mode bug
>>> mmc: tegra: Set SDHCI_QUIRK2_TUNE_DIS_CARD_CLK on Tegra210
>>> mmc: tegra: Enable UHS and HS200 modes for Tegra210
>>> mmc: tegra: Enable UHS and HS200 modes for Tegra186
>>> arm64: dts: Add Tegra210 sdmmc pinctrl voltage states
>>> arm64: dts: Add Tegra186 sdmmc pinctrl voltage states
>>> arm64: dts: tegra210-p2180: Allow ldo2 to go down to 1.8 V
>>> arm64: dts: tegra210-p2180: Correct sdmmc4 vqmmc-supply
>>> arm64: dts: tegra210-p2597: Remove no-1-8-v from sdmmc1
>>> arm64: dts: tegra186: Add sdmmc pad auto calibration offsets
>>> arm64: dts: tegra210: Add sdmmc pad auto calibration offsets
>>> arm64: dts: tegra210: Add SDHCI tap and trim values
>>> arm64: dts: tegra186: Add SDHCI tap and trim values
>>> arm64: dts: tegra186: Assign clocks for sdmmc1 and sdmmc4
>>> arm64: dts: tegra210: Assign clocks for sdmmc1 and sdmmc4
>>>
>>> .../bindings/arm/tegra/nvidia,tegra186-pmc.txt | 93 ++++
>>> .../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 103 ++++
>>> .../bindings/mmc/nvidia,tegra20-sdhci.txt | 68 +++
>>> arch/arm64/boot/dts/nvidia/tegra186.dtsi | 74 +++
>>> arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi | 12 +-
>>> arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi | 1 -
>>> arch/arm64/boot/dts/nvidia/tegra210.dtsi | 55 ++
>>> drivers/mmc/host/sdhci-tegra.c | 556 +++++++++++++++++++--
>>> drivers/mmc/host/sdhci.c | 21 +
>>> drivers/mmc/host/sdhci.h | 4 +
>>> drivers/soc/tegra/pmc.c | 511 ++++++++++++++-----
>>> include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h | 18 +
>>> include/soc/tegra/pmc.h | 20 +-
>>> 13 files changed, 1324 insertions(+), 212 deletions(-)
>>> create mode 100644 include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
>>
>> Adrian,
>>
>> these patches are also a prerequisite for the UHS signalling changes in
>> the other two series that Aapo posted. It'd be great if you could take a
>> quick look and weigh in.
>
> Sure, I'll try and have a look today.

Apart from the 2 new quirks which I made comments on, the rest seems fine.

\
 
 \ /
  Last update: 2018-08-27 13:46    [W:0.052 / U:0.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site