lkml.org 
[lkml]   [2018]   [Aug]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 7/7] Documentation: devicetree: Add Xilinx R5 rproc binding
On Fri, Aug 17, 2018 at 9:31 AM, Moritz Fischer
<moritz.fischer@ettus.com> wrote:
> Hi Wendy,
>
> couple of minor stuff inline.
>
> On Thu, Aug 16, 2018 at 12:06 AM, Wendy Liang <wendy.liang@xilinx.com> wrote:
>> Add device tree binding for Xilinx Cortex-r5 remoteproc.
>>
>> Signed-off-by: Wendy Liang <jliang@xilinx.com>
>> ---
>> .../remoteproc/xlnx,zynqmp-r5-remoteproc.txt | 81 ++++++++++++++++++++++
>> 1 file changed, 81 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5-remoteproc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5-remoteproc.txt b/Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5-remoteproc.txt
>> new file mode 100644
>> index 0000000..3940019
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5-remoteproc.txt
>> @@ -0,0 +1,81 @@
>> +Xilinx ARM Cortex A53-R5 remoteproc driver
>> +==========================================
>> +
>> +ZynqMP family of devices use two Cortex R5 processors to help with various
>> +low power / real time tasks.
>
> The ZynqMP family [..] uses [..]
Will update in next version
>> +
>> +This driver requires specific ZynqMP hardware design.
>
> *a* specific ZynqMP hardware design. What does that mean?
>> +
>> +ZynqMP R5 RemoteProc Device Node:
>> +=================================
>> +A zynqmp_r5_remoteproc device node is used to represent a R5 IP instance
>> +within ZynqMP SoC.
>> +
>> +Required properties:
>> +--------------------
>> + - compatible : Should be "xlnx,zynqmp-r5-remoteproc-1.0"
>> + - reg : Address and length of the register set for the device. It
>> + contains in the same order as described reg-names
>
> ?
>> + - reg-names: Contain the register set names.
>
> Contains
Will update in next version
>
>> + "tcm_a" and "tcm_b" for TCM memories.
>> + If the user uses the remoteproc driver with the RPMsg kernel
>> + driver,"ipi" for the IPI register used to communicate with RPU
>> + is also required.
>> + Otherwise, if user only uses the remoteproc driver to boot RPU
>> + firmware, "ipi" is not required.
>> + - tcm-pnode-id: TCM resources power nodes IDs which are used to request TCM
>> + resources for the remoteproc driver to access.
>> + - rpu-pnode-id : RPU power node id which is used by the remoteproc driver
>> + to start RPU or shut it down.
>> +
>> +Optional properties:
>> +--------------------
>> + - core_conf : R5 core configuration (valid string - split0 or split1 or
>> + lock-step), default is lock-step.
>> + - memory-region: memories regions for RPU executable and DMA memory.
>> + - interrupts : Interrupt mapping for remoteproc IPI. It is required if the
>> + user uses the remoteproc driver with the RPMsg kernel driver.
>> + - interrupt-parent : Phandle for the interrupt controller. It is required if
>> + the user uses the remoteproc driver with the RPMsg kernel
>> + kernel driver.
>> +
>> +Example:
>> +--------
>> + reserved-memory {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> + rproc_0_fw_reserved: rproc@3ed000000 {
>> + compatible = "rproc-prog-memory";
>> + no-map;
>> + reg = <0x0 0x3ed00000 0x0 0x40000>;
>> + };
>> + rproc_0_dma_reserved: rproc@3ed400000 {
>> + compatible = "shared-dma-pool";
>> + no-map;
>> + reg = <0x0 0x3ed40000 0x0 0x80000>;
>> + };
>> + };
>> +
>> + firmware {
>> + zynqmp_firmware: zynqmp-firmware {
>> + compatible = "xlnx,zynqmp-firmware";
>> + method = "smc";
>> + };
>> + };
>> +
>> + zynqmp-r5-remoteproc@0 {
>> + compatible = "xlnx,zynqmp-r5-remoteproc-1.0";
>> + reg = <0x0 0xFFE00000 0x0 0x10000>,
>> + <0x0 0xFFE20000 0x0 0x10000>,
>> + <0x0 0xff340000 0x0 0x100>;
>> + reg-names = "tcm_a", "tcm_b", "ipi";
>> + dma-ranges;
>> + core_conf = "split0";
>> + memory-region = <&rproc_0_fw_reserved>,
>> + <&rproc_0_dma_reserved>;
>> + tcm-pnode-id = <0xf>, <0x10>;
>> + rpu-pnode-id = <0x7>;
>> + interrupt-parent = <&gic>;
>> + interrupts = <0 29 4>;
>> + } ;
>> --
>> 2.7.4
>>
>
> Cheers,
> Moritz

\
 
 \ /
  Last update: 2018-08-20 07:56    [W:0.688 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site