lkml.org 
[lkml]   [2018]   [Aug]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2] eeprom: at24: Fix unexpected timeout under high load
Date
From: Wang Xin <xin.wang7@cn.bosch.com>

Within at24_loop_until_timeout the timestamp used for timeout checking
is recorded after the I2C transfer and sleep_range(). Under high CPU
load either the execution time for I2C transfer or sleep_range() could
actually be larger than the timeout value. Worst case the I2C transfer
is only tried once because the loop will exit due to the timeout
although the EEPROM is now ready.

To fix this issue the timestamp is recorded at the beginning of each
iteration. That is, before I2C transfer and sleep. Then the timeout
is actually checked against the timestamp of the previous iteration.
This makes sure that even if the timeout is reached, there is still one
more chance to try the I2C transfer in case the EEPROM is ready.

Example:

If you have a system which combines high CPU load with repeated EEPROM
writes you will run into the following scenario.

- System makes a successful regmap_bulk_write() to EEPROM.
- System wants to perform another write to EEPROM but EEPROM is still
busy with the last write.
- Because of high CPU load the usleep_range() will sleep more than
25 ms (at24_write_timeout).
- Within the over-long sleeping the EEPROM finished the previous write
operation and is ready again.
- at24_loop_until_timeout() will detect timeout and won't try to write.

Signed-off-by: Wang Xin <xin.wang7@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
---
Changes in v2:
- Remove loop macro
- Accept superfluous sleep in case of timeout
- Add concrete example to commit message
---
drivers/misc/eeprom/at24.c | 43 ++++++++++++++++++++++---------------------
1 file changed, 22 insertions(+), 21 deletions(-)

diff --git a/drivers/misc/eeprom/at24.c b/drivers/misc/eeprom/at24.c
index f5cc517..37a5c8b 100644
--- a/drivers/misc/eeprom/at24.c
+++ b/drivers/misc/eeprom/at24.c
@@ -106,23 +106,6 @@ static unsigned int at24_write_timeout = 25;
module_param_named(write_timeout, at24_write_timeout, uint, 0);
MODULE_PARM_DESC(at24_write_timeout, "Time (in ms) to try writes (default 25)");

-/*
- * Both reads and writes fail if the previous write didn't complete yet. This
- * macro loops a few times waiting at least long enough for one entire page
- * write to work while making sure that at least one iteration is run before
- * checking the break condition.
- *
- * It takes two parameters: a variable in which the future timeout in jiffies
- * will be stored and a temporary variable holding the time of the last
- * iteration of processing the request. Both should be unsigned integers
- * holding at least 32 bits.
- */
-#define at24_loop_until_timeout(tout, op_time) \
- for (tout = jiffies + msecs_to_jiffies(at24_write_timeout), \
- op_time = 0; \
- op_time ? time_before(op_time, tout) : true; \
- usleep_range(1000, 1500), op_time = jiffies)
-
struct at24_chip_data {
/*
* these fields mirror their equivalents in
@@ -308,13 +291,22 @@ static ssize_t at24_regmap_read(struct at24_data *at24, char *buf,
/* adjust offset for mac and serial read ops */
offset += at24->offset_adj;

- at24_loop_until_timeout(timeout, read_time) {
+ timeout = jiffies + msecs_to_jiffies(at24_write_timeout);
+ do {
+ /*
+ * The timestamp shall be taken before the actual operation
+ * to avoid a premature timeout in case of high CPU load.
+ */
+ read_time = jiffies;
+
ret = regmap_bulk_read(regmap, offset, buf, count);
dev_dbg(&client->dev, "read %zu@%d --> %d (%ld)\n",
count, offset, ret, jiffies);
if (!ret)
return count;
- }
+
+ usleep_range(1000, 1500);
+ } while (time_before(read_time, timeout));

return -ETIMEDOUT;
}
@@ -358,14 +350,23 @@ static ssize_t at24_regmap_write(struct at24_data *at24, const char *buf,
regmap = at24_client->regmap;
client = at24_client->client;
count = at24_adjust_write_count(at24, offset, count);
+ timeout = jiffies + msecs_to_jiffies(at24_write_timeout);
+
+ do {
+ /*
+ * The timestamp shall be taken before the actual operation
+ * to avoid a premature timeout in case of high CPU load.
+ */
+ write_time = jiffies;

- at24_loop_until_timeout(timeout, write_time) {
ret = regmap_bulk_write(regmap, offset, buf, count);
dev_dbg(&client->dev, "write %zu@%d --> %d (%ld)\n",
count, offset, ret, jiffies);
if (!ret)
return count;
- }
+
+ usleep_range(1000, 1500);
+ } while (time_before(write_time, timeout));

return -ETIMEDOUT;
}
--
2.7.4
\
 
 \ /
  Last update: 2018-08-16 19:46    [W:0.105 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site