lkml.org 
[lkml]   [2018]   [Aug]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 1/3] i2c: imx: Fix race condition in dma read
Date
From: Esben Haabendal <eha@deif.com>

This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).

Fixed by setting the DMAEN bit before the dummy read.

Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
drivers/i2c/busses/i2c-imx.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index 498c5e891649..ad6adefb64da 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -668,9 +668,6 @@ static int i2c_imx_dma_read(struct imx_i2c_struct *i2c_imx,
struct imx_i2c_dma *dma = i2c_imx->dma;
struct device *dev = &i2c_imx->adapter.dev;

- temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
- temp |= I2CR_DMAEN;
- imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);

dma->chan_using = dma->chan_rx;
dma->dma_transfer_dir = DMA_DEV_TO_MEM;
@@ -783,6 +780,7 @@ static int i2c_imx_read(struct imx_i2c_struct *i2c_imx, struct i2c_msg *msgs, bo
int i, result;
unsigned int temp;
int block_data = msgs->flags & I2C_M_RECV_LEN;
+ int use_dma = i2c_imx->dma && msgs->len >= DMA_THRESHOLD && !block_data;

dev_dbg(&i2c_imx->adapter.dev,
"<%s> write slave address: addr=0x%x\n",
@@ -809,12 +807,14 @@ static int i2c_imx_read(struct imx_i2c_struct *i2c_imx, struct i2c_msg *msgs, bo
*/
if ((msgs->len - 1) || block_data)
temp &= ~I2CR_TXAK;
+ if (use_dma)
+ temp |= I2CR_DMAEN;
imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR); /* dummy read */

dev_dbg(&i2c_imx->adapter.dev, "<%s> read data\n", __func__);

- if (i2c_imx->dma && msgs->len >= DMA_THRESHOLD && !block_data)
+ if (use_dma)
return i2c_imx_dma_read(i2c_imx, msgs, is_lastmsg);

/* read data */
--
2.18.0
\
 
 \ /
  Last update: 2018-08-16 10:45    [W:3.057 / U:0.320 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site