lkml.org 
[lkml]   [2018]   [Aug]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 4/5] arm64: dts: mt7622: add bananapi BPI-R64 board
From
Date
Hi, Ryder

On Wed, 2018-08-15 at 13:18 +0800, Ryder Lee wrote:
> Add support for the bananapi R64 (BPI-R64) development board from
> BIPAI KEJI. Detailed hardware information for BPI-R64 which could be
> found on http://wiki.banana-pi.org/Banana_Pi_BPI-R64
>
> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> .../boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts | 508 +++++++++++++++++++++
> 2 files changed, 509 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index ac17f60..2a1abe5 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -3,5 +3,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
> new file mode 100644
> index 0000000..bc504fe
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
> @@ -0,0 +1,508 @@
> +/*
> + * Copyright (c) 2018 MediaTek Inc.
> + * Author: Ryder Lee <ryder.lee@mediatek.com>
> + *
> + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/gpio/gpio.h>
> +
> +#include "mt7622.dtsi"
> +#include "mt6380.dtsi"
> +
> +/ {
> + model = "Bananapi BPI-R64";
> + compatible = "bananapi,bpi-r64", "mediatek,mt7622";
> +
> + chosen {
> + bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512";
> + };
> +
> + cpus {
> + cpu@0 {
> + proc-supply = <&mt6380_vcpu_reg>;
> + sram-supply = <&mt6380_vm_reg>;
> + };
> +
> + cpu@1 {
> + proc-supply = <&mt6380_vcpu_reg>;
> + sram-supply = <&mt6380_vm_reg>;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + poll-interval = <100>;
> +

the property poll-interval seems be only for a gpio-keys-polled device

> + factory {
> + label = "factory";
> + linux,code = <BTN_0>;
> + gpios = <&pio 0 0>;
> + };
> +
> + wps {
> + label = "wps";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&pio 102 0>;
> + };
> + };
> +
> + memory {
> + reg = <0 0x40000000 0 0x40000000>;
> + };
> +
> + reg_1p8v: regulator-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "fixed-1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + reg_3p3v: regulator-3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "fixed-3.3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_5v: regulator-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "fixed-5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +};
> +
> +&bch {
> + status = "disabled";
> +};
> +
> +&btif {
> + status = "okay";
> +};
> +
> +&cir {
> + pinctrl-names = "default";
> + pinctrl-0 = <&irrx_pins>;
> + status = "okay";
> +};
> +
> +&eth {
> + pinctrl-names = "default";
> + pinctrl-0 = <&eth_pins>;
> + status = "okay";
> +
> + gmac1: mac@1 {
> + compatible = "mediatek,eth-mac";
> + reg = <1>;
> + phy-handle = <&phy5>;
> + };
> +
> + mdio-bus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy5: ethernet-phy@5 {
> + reg = <5>;
> + phy-mode = "sgmii";
> + };
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> + status = "okay";
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&emmc_pins_default>;
> + pinctrl-1 = <&emmc_pins_uhs>;
> + status = "okay";
> + bus-width = <8>;
> + max-frequency = <50000000>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + vmmc-supply = <&reg_3p3v>;
> + vqmmc-supply = <&reg_1p8v>;
> + assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
> + assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
> + non-removable;
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&sd0_pins_default>;
> + pinctrl-1 = <&sd0_pins_uhs>;
> + status = "okay";
> + bus-width = <4>;
> + max-frequency = <50000000>;
> + cap-sd-highspeed;
> + r_smpl = <1>;
> + cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
> + vmmc-supply = <&reg_3p3v>;
> + vqmmc-supply = <&reg_3p3v>;
> + assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
> + assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
> +};
> +
> +&nandc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&parallel_nand_pins>;
> + status = "disabled";
> +};
> +
> +&nor_flash {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_nor_pins>;
> + status = "disabled";
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + };
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie0_pins>;
> + pinctrl-1 = <&pcie1_pins>;

it should be pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>;

otherwise, no name is being mapped into pinctrl-1 setup

> + status = "okay";
> +
> + pcie@0,0 {
> + status = "okay";
> + };
> +
> + pcie@1,0 {
> + status = "okay";
> + };
> +};
> +
> +&pio {
> + /* Attention: GPIO 90 is used to switch between PCIe@1,0 and
> + * SATA functions. i.e. output-high: PCIe, output-low: SATA
> + */


the sata node seems be missing in the newly added dts

> + asm_sel {
> + gpio-hog;
> + gpios = <90 GPIO_ACTIVE_HIGH>;
> + output-high;
> + };
> +
> + /* eMMC is shared pin with parallel NAND */
> + emmc_pins_default: emmc-pins-default {
> + mux {
> + function = "emmc", "emmc_rst";
> + groups = "emmc";
> + };
> +
> + /* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
> + * "NRB","NCLE" pins are used as DAT0,DAT1,DAT2,DAT3,DAT4,
> + * DAT5,DAT6,DAT7,CMD,CLK for eMMC respectively
> + */
> + conf-cmd-dat {
> + pins = "NDL0", "NDL1", "NDL2",
> + "NDL3", "NDL4", "NDL5",
> + "NDL6", "NDL7", "NRB";
> + input-enable;
> + bias-pull-up;
> + };
> +
> + conf-clk {
> + pins = "NCLE";
> + bias-pull-down;
> + };
> + };
> +
> + emmc_pins_uhs: emmc-pins-uhs {
> + mux {
> + function = "emmc";
> + groups = "emmc";
> + };
> +
> + conf-cmd-dat {
> + pins = "NDL0", "NDL1", "NDL2",
> + "NDL3", "NDL4", "NDL5",
> + "NDL6", "NDL7", "NRB";
> + input-enable;
> + drive-strength = <4>;
> + bias-pull-up;
> + };
> +
> + conf-clk {
> + pins = "NCLE";
> + drive-strength = <4>;
> + bias-pull-down;
> + };
> + };
> +
> + eth_pins: eth-pins {
> + mux {
> + function = "eth";
> + groups = "mdc_mdio", "rgmii_via_gmac2";
> + };
> + };
> +
> + i2c1_pins: i2c1-pins {
> + mux {
> + function = "i2c";
> + groups = "i2c1_0";
> + };
> + };
> +
> + i2c2_pins: i2c2-pins {
> + mux {
> + function = "i2c";
> + groups = "i2c2_0";
> + };
> + };
> +
> + i2s1_pins: i2s1-pins {
> + mux {
> + function = "i2s";
> + groups = "i2s_out_mclk_bclk_ws",
> + "i2s1_in_data",
> + "i2s1_out_data";
> + };
> +
> + conf {
> + pins = "I2S1_IN", "I2S1_OUT", "I2S_BCLK",
> + "I2S_WS", "I2S_MCLK";
> + drive-strength = <12>;
> + bias-pull-down;
> + };
> + };
> +
> + irrx_pins: irrx-pins {
> + mux {
> + function = "ir";
> + groups = "ir_1_rx";
> + };
> + };
> +
> + irtx_pins: irtx-pins {
> + mux {
> + function = "ir";
> + groups = "ir_1_tx";
> + };
> + };
> +
> + /* Parallel nand is shared pin with eMMC */
> + parallel_nand_pins: parallel-nand-pins {
> + mux {
> + function = "flash";
> + groups = "par_nand";
> + };
> + };
> +
> + pcie0_pins: pcie0-pins {
> + mux {
> + function = "pcie";
> + groups = "pcie0_pad_perst",
> + "pcie0_1_waken",
> + "pcie0_1_clkreq";
> + };
> + };
> +
> + pcie1_pins: pcie1-pins {
> + mux {
> + function = "pcie";
> + groups = "pcie1_pad_perst",
> + "pcie1_0_waken",
> + "pcie1_0_clkreq";
> + };
> + };
> +
> + pmic_bus_pins: pmic-bus-pins {
> + mux {
> + function = "pmic";
> + groups = "pmic_bus";
> + };
> + };
> +
> + pwm7_pins: pwm1-2-pins {
> + mux {
> + function = "pwm";
> + groups = "pwm_ch7_2";
> + };
> + };
> +
> + wled_pins: wled-pins {
> + mux {
> + function = "led";
> + groups = "wled";
> + };
> + };
> +
> + sd0_pins_default: sd0-pins-default {
> + mux {
> + function = "sd";
> + groups = "sd_0";
> + };
> +
> + /* "I2S2_OUT, "I2S4_IN"", "I2S3_IN", "I2S2_IN",
> + * "I2S4_OUT", "I2S3_OUT" are used as DAT0, DAT1,
> + * DAT2, DAT3, CMD, CLK for SD respectively.
> + */
> + conf-cmd-data {
> + pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
> + "I2S2_IN","I2S4_OUT";
> + input-enable;
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + conf-clk {
> + pins = "I2S3_OUT";
> + drive-strength = <12>;
> + bias-pull-down;
> + };
> + conf-cd {
> + pins = "TXD3";
> + bias-pull-up;
> + };
> + };
> +
> + sd0_pins_uhs: sd0-pins-uhs {
> + mux {
> + function = "sd";
> + groups = "sd_0";
> + };
> +
> + conf-cmd-data {
> + pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
> + "I2S2_IN","I2S4_OUT";
> + input-enable;
> + bias-pull-up;
> + };
> +
> + conf-clk {
> + pins = "I2S3_OUT";
> + bias-pull-down;
> + };
> + };
> +
> + /* Serial NAND is shared pin with SPI-NOR */
> + serial_nand_pins: serial-nand-pins {
> + mux {
> + function = "flash";
> + groups = "snfi";
> + };
> + };
> +
> + spic0_pins: spic0-pins {
> + mux {
> + function = "spi";
> + groups = "spic0_0";
> + };
> + };
> +
> + spic1_pins: spic1-pins {
> + mux {
> + function = "spi";
> + groups = "spic1_0";
> + };
> + };
> +
> + /* SPI-NOR is shared pin with serial NAND */
> + spi_nor_pins: spi-nor-pins {
> + mux {
> + function = "flash";
> + groups = "spi_nor";
> + };
> + };
> +
> + /* serial NAND is shared pin with SPI-NOR */
> + serial_nand_pins: serial-nand-pins {
> + mux {
> + function = "flash";
> + groups = "snfi";
> + };
> + };
> +
> + uart0_pins: uart0-pins {
> + mux {
> + function = "uart";
> + groups = "uart0_0_tx_rx" ;
> + };
> + };
> +
> + uart2_pins: uart2-pins {
> + mux {
> + function = "uart";
> + groups = "uart2_1_tx_rx" ;
> + };
> + };
> +
> + watchdog_pins: watchdog-pins {
> + mux {
> + function = "watchdog";
> + groups = "watchdog";
> + };
> + };
> +};
> +
> +&pwm {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm7_pins>;
> + status = "okay";
> +};
> +
> +&pwrap {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_bus_pins>;
> +
> + status = "okay";
> +};
> +
> +&spi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spic0_pins>;
> + status = "okay";
> +};
> +
> +&spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spic1_pins>;
> + status = "okay";
> +};
> +
> +&ssusb {
> + vusb33-supply = <&reg_3p3v>;
> + vbus-supply = <&reg_5v>;
> + status = "okay";
> +};
> +
> +&u3phy {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2_pins>;
> + status = "okay";
> +};
> +
> +&watchdog {
> + pinctrl-names = "default";
> + pinctrl-0 = <&watchdog_pins>;
> + status = "okay";
> +};


\
 
 \ /
  Last update: 2018-08-16 09:52    [W:1.950 / U:0.100 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site