lkml.org 
[lkml]   [2018]   [Jul]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 1/1] mmc: sunxi: Disable irq during pm_suspend
+ Marc

On 4 July 2018 at 08:28, Stefan Mavrodiev <stefan@olimex.com> wrote:
> When mmc host controller enters suspend state, the clocks are
> disabled, but irqs are not. For some reason the irqchip emits
> false interrupts, which causes system lock loop.
>
> Debug log is:
> ...
> sunxi-mmc 1c11000.mmc: setting clk to 52000000, rounded 51200000
> sunxi-mmc 1c11000.mmc: enabling the clock
> sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
> sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
> sunxi-mmc 1c11000.mmc: cmd 6(80000146) arg 3210101 ie 0x0000bbc6 len 0
> sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
> sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
> sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
> mmc1: new DDR MMC card at address 0001
> mmcblk1: mmc1:0001 AGND3R 14.6 GiB
> mmcblk1boot0: mmc1:0001 AGND3R partition 1 4.00 MiB
> mmcblk1boot1: mmc1:0001 AGND3R partition 2 4.00 MiB
> sunxi-mmc 1c11000.mmc: cmd 18(80003352) arg 0 ie 0x0000fbc2 len 409
> sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00004000 idi 00000002
> mmcblk1: p1
> sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
> sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
> sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
> sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
> and so on...
>
> This issue apears on eMMC cards, routed on MMC2 slot. The patch is
> tested with A20-OLinuXino-MICRO/LIME/LIME2 boards.
>
> Fixes: 9a8e1e8cc2c0 ("mmc: sunxi: Add runtime_pm support")
> Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
> ---
> Changes in v2:
> - Add comment why disable_irq() is necessary
>
> ---
> drivers/mmc/host/sunxi-mmc.c | 7 +++++++
> 1 file changed, 7 insertions(+)
>
> diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
> index e747259..8e7f3e3 100644
> --- a/drivers/mmc/host/sunxi-mmc.c
> +++ b/drivers/mmc/host/sunxi-mmc.c
> @@ -1446,6 +1446,7 @@ static int sunxi_mmc_runtime_resume(struct device *dev)
> sunxi_mmc_init_host(host);
> sunxi_mmc_set_bus_width(host, mmc->ios.bus_width);
> sunxi_mmc_set_clk(host, &mmc->ios);
> + enable_irq(host->irq);
>
> return 0;
> }
> @@ -1455,6 +1456,12 @@ static int sunxi_mmc_runtime_suspend(struct device *dev)
> struct mmc_host *mmc = dev_get_drvdata(dev);
> struct sunxi_mmc_host *host = mmc_priv(mmc);
>
> + /*
> + * When clocks are off, it's possible receiving
> + * fake interrupts, which will stall the system.
> + * Disabling the irq will prevent this.
> + */
> + disable_irq(host->irq);

No, this doesn't work for shared IRQs.

> sunxi_mmc_reset_host(host);
> sunxi_mmc_disable(host);
>
> --
> 2.7.4
>

The only option today is to use free_irq() in runtime suspend and then
re-request the irq to re-install the handler at runtime resume.

That's not an optimal solution, which is pointed out in the below
discussion as well. Moreover, it has also turned out using free_irq()
is also problematic in cases threaded handlers are used.

Here's the link to the discussion, it's not the only one I know of, so
this is common problem.
https://lkml.org/lkml/2016/1/28/213

Care to have a hack on the "common" solution, which in principle means
adding APIs to genirq that can disable/enable handlers from being
called, rather than the entire IRQ line.

Kind regards
Uffe

\
 
 \ /
  Last update: 2018-07-04 12:51    [W:0.135 / U:0.812 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site