lkml.org 
[lkml]   [2018]   [Jul]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V2 net-next 7/9] net: hns3: give default option while dependency HNS3 set
Date
From: Huazhong Tan <tanhuazhong@huawei.com>

Give default option for HNS3_HCLGE and HNS3_ENET will be helpful,
while dependency HNS3 is set. Meanwhile, use "if HNS3" section
instead of all the "depends on HNS3".

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
---
drivers/net/ethernet/hisilicon/Kconfig | 15 +++++++++------
1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/hisilicon/Kconfig b/drivers/net/ethernet/hisilicon/Kconfig
index 8bcf470..27edca8 100644
--- a/drivers/net/ethernet/hisilicon/Kconfig
+++ b/drivers/net/ethernet/hisilicon/Kconfig
@@ -85,10 +85,12 @@ config HNS3
drivers(like ODP)to register with HNAE devices and their associated
operations.

+if HNS3
+
config HNS3_HCLGE
tristate "Hisilicon HNS3 HCLGE Acceleration Engine & Compatibility Layer Support"
+ default m
depends on PCI_MSI
- depends on HNS3
---help---
This selects the HNS3_HCLGE network acceleration engine & its hardware
compatibility layer. The engine would be used in Hisilicon hip08 family of
@@ -97,16 +99,15 @@ config HNS3_HCLGE
config HNS3_DCB
bool "Hisilicon HNS3 Data Center Bridge Support"
default n
- depends on HNS3 && HNS3_HCLGE && DCB
+ depends on HNS3_HCLGE && DCB
---help---
Say Y here if you want to use Data Center Bridging (DCB) in the HNS3 driver.

If unsure, say N.

config HNS3_HCLGEVF
- tristate "Hisilicon HNS3VF Acceleration Engine & Compatibility Layer Support"
- depends on PCI_MSI
- depends on HNS3
+ tristate "Hisilicon HNS3VF Acceleration Engine & Compatibility Layer Support"
+ depends on PCI_MSI
depends on HNS3_HCLGE
---help---
This selects the HNS3 VF drivers network acceleration engine & its hardware
@@ -115,11 +116,13 @@ config HNS3_HCLGEVF

config HNS3_ENET
tristate "Hisilicon HNS3 Ethernet Device Support"
+ default m
depends on 64BIT && PCI
- depends on HNS3
---help---
This selects the Ethernet Driver for Hisilicon Network Subsystem 3 for hip08
family of SoCs. This module depends upon HNAE3 driver to access the HNAE3
devices and their associated operations.

+endif #HNS3
+
endif # NET_VENDOR_HISILICON
--
1.9.1
\
 
 \ /
  Last update: 2018-07-02 09:20    [W:0.050 / U:2.564 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site