lkml.org 
[lkml]   [2018]   [Jul]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3 5/7] dt-bindings: Add Tegra PMC pad configuration bindings
On Tue, Jul 17, 2018 at 6:23 AM Aapo Vienamo <avienamo@nvidia.com> wrote:
>
> On Mon, 16 Jul 2018 09:43:09 -0600
> Rob Herring <robh@kernel.org> wrote:
>
> > On Thu, Jul 12, 2018 at 03:00:11PM +0300, Aapo Vienamo wrote:
> > > Document the pinctrl bindings used by the PMC driver for performing pad
> > > configuration. Both nvidia,tegra186-pmc.txt and nvidia,tegra20-pmc.txt
> > > are modified as they both cover SoC generations for which these bindings
> > > apply.
> > >
> > > Add a header defining Tegra PMC pad voltage configurations.
> > >
> > > Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
> > > Acked-by: Jon Hunter <jonathanh@nvidia.com>
> > > ---
> > > .../bindings/arm/tegra/nvidia,tegra186-pmc.txt | 84 +++++++++++++++++++
> > > .../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 95 ++++++++++++++++++++++
> > > include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h | 18 ++++
> > > 3 files changed, 197 insertions(+)
> > > create mode 100644 include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
> > >
> > > diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
> > > index 5a3bf7c..9528f41 100644
> > > --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
> > > +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
> > > @@ -34,3 +34,87 @@ Board DTS:
> > > pmc@c360000 {
> > > nvidia,invert-interrupt;
> > > };
> > > +
> > > +== Pad Control Nodes ==
> > > +
> > > +The PMC can be used to set pad power state and voltage configuration.
> > > +The pad configuration is done via the pinctrl framework. The driver
> > > +implements power-source, low-power-enable, and low-power-disable pinconf
> > > +pin configuration node properties. Each pinctrl pin corresponds to a
> > > +single Tegra PMC pad. Thus, in the following sections of this document
> > > +pin refers to the pinctrl frameworks notion of a Tegra PMC pad.
> >
> > "pinctrl framework" is Linux specific and doesn't belong in the binding.
> > Neither does what a driver supports. Describe what the h/w supports.
> >
> > > +
> > > +The pad configuration state nodes are placed under the pmc node and they
> > > +are referred to by the pinctrl client device properties. For more
> >
> > Another driver detail not relevant.
> >
> > > +information see the examples presented later and
> >
> > examples don't document bindings. The documentation should be complete
> > without examples.
> >
> > > +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
> > > +
> > > +The values accepted by power-source property are
> > > +TEGRA_IO_PAD_VOLTAGE_1V8 and TEGRA_IO_PAD_VOLTAGE_3V3, which are defined
> > > +in dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
> >
> > You need to list out what properties the child nodes can have.
> >
> > power-source needs a vendor prefix.
>
> Isn't it a generic pinctrl property?

I don't know offhand. Doesn't look like it if you have custom values.

Rob

\
 
 \ /
  Last update: 2018-07-17 16:23    [W:0.058 / U:0.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site