lkml.org 
[lkml]   [2018]   [Jul]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] Input: atmel_mxt_ts: Add support for optional regulators.
Hi Paweł,

On Fri, Jul 13, 2018 at 08:30:07PM +0200, Paweł Chmiel wrote:
> This patch adds optional regulators, which can be used to power
> up touchscreen. After enabling regulators, we need to wait 150msec.
> This value is taken from official driver.
>
> It was tested on Samsung Galaxy i9000 (based on Samsung S5PV210 SOC).
>
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> ---
> drivers/input/touchscreen/atmel_mxt_ts.c | 45 ++++++++++++++++++++++++++++++++
> 1 file changed, 45 insertions(+)
>
> diff --git a/drivers/input/touchscreen/atmel_mxt_ts.c b/drivers/input/touchscreen/atmel_mxt_ts.c
> index 54fe190fd4bc..a7625ec8fb9f 100644
> --- a/drivers/input/touchscreen/atmel_mxt_ts.c
> +++ b/drivers/input/touchscreen/atmel_mxt_ts.c
> @@ -27,6 +27,7 @@
> #include <linux/interrupt.h>
> #include <linux/of.h>
> #include <linux/property.h>
> +#include <linux/regulator/consumer.h>
> #include <linux/slab.h>
> #include <linux/gpio/consumer.h>
> #include <linux/property.h>
> @@ -198,6 +199,7 @@ enum t100_type {
> #define MXT_RESET_INVALID_CHG 100 /* msec */
> #define MXT_RESET_TIME 200 /* msec */
> #define MXT_RESET_TIMEOUT 3000 /* msec */
> +#define MXT_REGULATOR_DELAY 150 /* msec */
> #define MXT_CRC_TIMEOUT 1000 /* msec */
> #define MXT_FW_RESET_TIME 3000 /* msec */
> #define MXT_FW_CHG_TIMEOUT 300 /* msec */
> @@ -310,6 +312,8 @@ struct mxt_data {
> struct t7_config t7_cfg;
> struct mxt_dbg dbg;
> struct gpio_desc *reset_gpio;
> + struct regulator *vdd_reg;
> + struct regulator *avdd_reg;
>
> /* Cached parameters from object table */
> u16 T5_address;
> @@ -3076,6 +3080,40 @@ static int mxt_probe(struct i2c_client *client, const struct i2c_device_id *id)
> return error;
> }
>
> + data->vdd_reg = devm_regulator_get_optional(&client->dev, "vdd");
> + if (IS_ERR(data->vdd_reg)) {
> + error = PTR_ERR(data->vdd_reg);
> + dev_err(&client->dev, "Failed to get vdd regulator: %d\n",
> + error);
> + return error;
> + }
> +
> + if (data->vdd_reg) {
> + error = regulator_enable(data->vdd_reg);
> + if (error) {
> + dev_err(&client->dev, "Failed to enable vdd regulator: %d\n",
> + error);
> + return error;
> + }
> + }
> +
> + data->avdd_reg = devm_regulator_get_optional(&client->dev, "avdd");
> + if (IS_ERR(data->avdd_reg)) {
> + error = PTR_ERR(data->avdd_reg);
> + dev_err(&client->dev, "Failed to get avdd regulator: %d\n",
> + error);
> + return error;
> + }
> +
> + if (data->avdd_reg) {

devm_regulator_get_optional() does not return NULL for regulators
not present in device tree, but rather -ENOENT, so this code is not
correct; neither is the simple IS_ERR() check above.

Moreover, the optional regulators should be used when there is a part of
IP block that can be optionally powered up, but the device can work
(with limited functionality) even when it is powered down. They should
not be used in cases when supplies are mandatory (such as vdd/avdd) but
may not be exposed to the kernel by the firmware.

Simply use devm_regulator_get() and rely on the fact that on fully
constrained system you will get a dummy regulator.

> + error = regulator_enable(data->avdd_reg);
> + if (error) {
> + dev_err(&client->dev, "Failed to enable avdd regulator: %d\n",
> + error);
> + return error;
> + }
> + }
> +
> error = devm_request_threaded_irq(&client->dev, client->irq,
> NULL, mxt_interrupt, IRQF_ONESHOT,
> client->name, data);
> @@ -3086,6 +3124,9 @@ static int mxt_probe(struct i2c_client *client, const struct i2c_device_id *id)
>
> disable_irq(client->irq);
>
> + if (!IS_ERR(data->vdd_reg) || !IS_ERR(data->avdd_reg))
> + msleep(MXT_REGULATOR_DELAY);
> +
> if (data->reset_gpio) {

I think you should require that if regulators are exposed then reset
gpio should also be present to ensure proper power up timings.

> msleep(MXT_RESET_GPIO_TIME);
> gpiod_set_value(data->reset_gpio, 1);
> @@ -3116,6 +3157,10 @@ static int mxt_remove(struct i2c_client *client)
> struct mxt_data *data = i2c_get_clientdata(client);
>
> disable_irq(data->irq);
> + if (!IS_ERR(data->avdd_reg))
> + regulator_disable(data->avdd_reg);
> + if (!IS_ERR(data->vdd_reg))
> + regulator_disable(data->vdd_reg);
> sysfs_remove_group(&client->dev.kobj, &mxt_attr_group);
> mxt_free_input_device(data);
> mxt_free_object_table(data);
> --
> 2.7.4
>

Thanks.

--
Dmitry
\
 
 \ /
  Last update: 2018-07-15 22:07    [W:0.049 / U:0.368 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site