lkml.org 
[lkml]   [2018]   [Jul]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 6/7] mhi_bus: controller: MHI support for QCOM modems
On Mon, Jul 09, 2018 at 01:08:13PM -0700, Sujeev Dias wrote:
> QCOM PCIe based modems uses MHI as the communication protocol.
> MHI control driver is the bus master for such modems. As the bus
> master driver, it oversees power management operations
> such as suspend, resume, powering on and off the device.
>
> Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
> Reviewed-by: Tony Truong <truong@codeaurora.org>
> Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
> ---
> Documentation/devicetree/bindings/bus/mhi_qcom.txt | 58 +++

And this one in it's own patch.

> arch/arm64/configs/defconfig | 1 +
> drivers/bus/Kconfig | 1 +
> drivers/bus/mhi/Makefile | 1 +
> drivers/bus/mhi/controllers/Kconfig | 13 +
> drivers/bus/mhi/controllers/Makefile | 1 +
> drivers/bus/mhi/controllers/mhi_qcom.c | 461 +++++++++++++++++++++
> drivers/bus/mhi/controllers/mhi_qcom.h | 67 +++
> 8 files changed, 603 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/bus/mhi_qcom.txt
> create mode 100644 drivers/bus/mhi/controllers/Kconfig
> create mode 100644 drivers/bus/mhi/controllers/Makefile
> create mode 100644 drivers/bus/mhi/controllers/mhi_qcom.c
> create mode 100644 drivers/bus/mhi/controllers/mhi_qcom.h
>
> diff --git a/Documentation/devicetree/bindings/bus/mhi_qcom.txt b/Documentation/devicetree/bindings/bus/mhi_qcom.txt
> new file mode 100644
> index 0000000..0a48a50
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/bus/mhi_qcom.txt
> @@ -0,0 +1,58 @@
> +Qualcomm Technologies Inc MHI Bus controller
> +
> +MHI control driver enables clients to communicate with external mode
> +using MHI protocol.
> +
> +==============
> +Node Structure
> +==============
> +
> +Main node properties:
> +
> +- reg
> + Usage: required
> + Value type: Array (5-cell PCI resource) of <u32>
> + Definition: First cell is devfn, which is determined by pci bus topology.
> + Assign the other cells 0 since they are not used.
> +
> +- qcom,smmu-cfg

This should probably be part of the SMMU binding?

> + Usage: required
> + Value type: <u32>
> + Definition: Required SMMU configuration bitmask for PCIe bus.
> + BIT mask:
> + BIT(0) : Attach address mapping to endpoint device
> + BIT(1) : Set attribute S1_BYPASS
> + BIT(2) : Set attribute FAST
> + BIT(3) : Set attribute ATOMIC
> + BIT(4) : Set attribute FORCE_COHERENT
> +
> +- qcom,addr-win
> + Usage: required if SMMU S1 translation is enabled
> + Value type: Array of <u64>
> + Definition: Pair of values describing iova start and stop address
> +
> +- MHI bus settings
> + Usage: required
> + Values: as defined by mhi.txt
> + Definition: Per definition of devicetree/bindings/bus/mhi.txt, define device
> + specific MHI configuration parameters.
> +
> +========
> +Example:
> +========
> +
> +/* pcie domain (root complex) modem connected to */
> +&pcie1 {
> + /* pcie bus modem connected to */
> + pci,bus@1 {
> + reg = <0 0 0 0 0>;
> +
> + qcom,mhi {
> + reg = <0 0 0 0 0>;

2 levels of PCI addresses doesn't look right, but I can't really tell in
your example. The addresses don't look valid.

> + qcom,smmu-cfg = <0x3d>;
> + qcom,addr-win = <0x0 0x20000000 0x0 0x3fffffff>;
> +
> + <mhi bus configurations>
> + };
> + };
> +};
\
 
 \ /
  Last update: 2018-07-15 22:05    [W:0.305 / U:0.272 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site