lkml.org 
[lkml]   [2018]   [Jun]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 4/8] serial: 8250: Handle case port doesn't have TEMT interrupt using em485.
From
Date
Hi,

Il 04/06/2018 13:38, Andy Shevchenko ha scritto:
> On Mon, 2018-06-04 at 12:50 +0200, Giulio Benetti wrote:
>> Hi,
>>
>> Il 04/06/2018 12:17, Andy Shevchenko ha scritto:
>>> On Fri, 2018-06-01 at 14:40 +0200, Giulio Benetti wrote:
>>>> Some 8250 ports only have TEMT interrupt, so current
>>>> implementation
>>>> can't work for ports without it. The only chance to make it work
>>>> is to
>>>> loop-read on LSR register.
>>>>
>>>> With NO TEMT interrupt check if both TEMT and THRE are set looping
>>>> on
>>>> LSR register.
>>>> --- a/drivers/tty/serial/8250/8250_dw.c
>>>> +++ b/drivers/tty/serial/8250/8250_dw.c
>>>> - int ret = serial8250_em485_init(up);
>>>> + int ret = serial8250_em485_init(up, false);
>>>
>>> Is true for all possible DW configured types? Or it's your
>>> particular
>>> case?
>>>
>>
>> I've checked on Synopsis Designware 8250 datasheet and it's not
>> supported.
>> Here is datasheet I went through:
>> https://linux-sunxi.org/images/d/d2/Dw_apb_uart_db.pdf
>>
>> There seems not to be TEMT interrupt, I use it under sunxi SoC and on
>> their datasheet(A20 for example), they don't report that interrupt
>> too.
>> So it seems to be valid for all DW configured types, anyway I don't
>> know
>> how many IP reviews there could be of that peripheral.
>
> This is an excerpt from the document you referred to:
>
> --- 8< --- 8< ---
>
> 6 TEMT R Transmitter Empty bit. If in FIFO mode (FIFO_MODE != NONE) and
> FIFOs enabled (FCR[0] set to one), this bit is set whenever the
> Transmitter Shift Register and the FIFO are both empty. If in non-FIFO
> mode or FIFOs are disabled, this bit is set whenever the Transmitter
> Holding Register and the Transmitter Shift Register are both empty.
>
> Reset Value: 0x1
>
> --- 8< --- 8< ---
>
>
> If I'm reading this correctly the support is there. Or otherwise, care
> to point exact paragraph needs to be read and checked?

In the beginning I thought the same as you but
unfortunately LSR is only a status register and IER doesn't have
corresponding TEMT bit to enable an interrupt on TEMT triggering.
On OMAP instead there is a specific interrupt bound to TEMT LSR flag.
And THRE interrupt is not enough because shift register won't be empty
when it triggers, so you would loose some bit of last byte to be
transmitted.

--
Giulio Benetti
CTO

MICRONOVA SRL
Sede: Via A. Niedda 3 - 35010 Vigonza (PD)
Tel. 049/8931563 - Fax 049/8931346
Cod.Fiscale - P.IVA 02663420285
Capitale Sociale € 26.000 i.v.
Iscritta al Reg. Imprese di Padova N. 02663420285
Numero R.E.A. 258642

\
 
 \ /
  Last update: 2018-06-04 13:51    [W:0.083 / U:1.332 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site