lkml.org 
[lkml]   [2018]   [Jun]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 05/11] docs/mm: bootmem: add overview documentation
Date
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
---
mm/bootmem.c | 47 +++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)

diff --git a/mm/bootmem.c b/mm/bootmem.c
index 76fc17e..97db0e8 100644
--- a/mm/bootmem.c
+++ b/mm/bootmem.c
@@ -21,6 +21,53 @@

#include "internal.h"

+/**
+ * DOC: bootmem overview
+ *
+ * Bootmem is a boot-time physical memory allocator and configurator.
+ *
+ * It is used early in the boot process before the page allocator is
+ * set up.
+ *
+ * Bootmem is based on the most basic of allocators, a First Fit
+ * allocator which uses a bitmap to represent memory. If a bit is 1,
+ * the page is allocated and 0 if unallocated. To satisfy allocations
+ * of sizes smaller than a page, the allocator records the Page Frame
+ * Number (PFN) of the last allocation and the offset the allocation
+ * ended at. Subsequent small allocations are merged together and
+ * stored on the same page.
+ *
+ * The information used by the bootmem allocator is represented by
+ * :c:type:`struct bootmem_data`. An array to hold up to %MAX_NUMNODES
+ * such structures is statically allocated and then it is discarded
+ * when the system initialization completes. Each entry in this array
+ * corresponds to a node with memory. For UMA systems only entry 0 is
+ * used.
+ *
+ * The bootmem allocator is initialized during early architecture
+ * specific setup. Each architecture is required to supply a
+ * :c:func:`setup_arch` function which, among other tasks, is
+ * responsible for acquiring the necessary parameters to initialise
+ * the boot memory allocator. These parameters define limits of usable
+ * physical memory:
+ *
+ * * @min_low_pfn - the lowest PFN that is available in the system
+ * * @max_low_pfn - the highest PFN that may be addressed by low
+ * memory (%ZONE_NORMAL)
+ * * @max_pfn - the last PFN available to the system.
+ *
+ * After those limits are determined, the :c:func:`init_bootmem` or
+ * :c:func:`init_bootmem_node` function should be called to initialize
+ * the bootmem allocator. The UMA case should use the `init_bootmem`
+ * function. It will initialize ``contig_page_data`` structure that
+ * represents the only memory node in the system. In the NUMA case the
+ * `init_bootmem_node` function should be called to initialize the
+ * bootmem allocator for each node.
+ *
+ * Once the allocator is set up, it is possible to use either single
+ * node or NUMA variant of the allocation APIs.
+ */
+
#ifndef CONFIG_NEED_MULTIPLE_NODES
struct pglist_data __refdata contig_page_data = {
.bdata = &bootmem_node_data[0]
--
2.7.4
\
 
 \ /
  Last update: 2018-06-30 16:58    [W:0.151 / U:24.684 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site