lkml.org 
[lkml]   [2018]   [May]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: [PATCH v2 2/2] leds: Add Spreadtrum SC27xx breathing light controller driver
Hi Jacek,

On 9 May 2018 at 04:54, Jacek Anaszewski <jacek.anaszewski@gmail.com> wrote:
> Hi Baolin,
>
> Thank you for the updated version.
>
> I have few notes below, please take a look.
>
>
> On 05/08/2018 07:39 AM, Baolin Wang wrote:
>>
>> From: Xiaotong Lu <xiaotong.lu@spreadtrum.com>
>>
>> This patch adds Spreadtrum SC27xx PMIC series breathing light controller
>> driver, which can support 3 LEDs. Each LED can work at normal PWM mode
>> and breathing mode.
>>
>> Signed-off-by: Xiaotong Lu <xiaotong.lu@spreadtrum.com>
>> Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
>> ---
>> Changes since v1:
>> - Add ABI documentation.
>> - Add mutex protection in case of concurrent access.
>> - Change the LED device name pattern.
>> - Fix build warning.
>> ---
>> .../ABI/testing/sysfs-class-led-driver-sc27xx | 19 +
>> drivers/leds/Kconfig | 11 +
>> drivers/leds/Makefile | 1 +
>> drivers/leds/leds-sc27xx-bltc.c | 387
>> ++++++++++++++++++++
>> 4 files changed, 418 insertions(+)
>> create mode 100644
>> Documentation/ABI/testing/sysfs-class-led-driver-sc27xx
>> create mode 100644 drivers/leds/leds-sc27xx-bltc.c
>>
>> diff --git a/Documentation/ABI/testing/sysfs-class-led-driver-sc27xx
>> b/Documentation/ABI/testing/sysfs-class-led-driver-sc27xx
>> new file mode 100644
>> index 0000000..22166fb
>> --- /dev/null
>> +++ b/Documentation/ABI/testing/sysfs-class-led-driver-sc27xx
>> @@ -0,0 +1,19 @@
>> +What: /sys/class/leds/<led>/rise_time
>> +What: /sys/class/leds/<led>/high_time
>> +What: /sys/class/leds/<led>/fall_time
>> +What: /sys/class/leds/<led>/low_time
>> +Date: May 2018
>> +KernelVersion: 4.18
>> +Contact: Xiaotong Lu <xiaotong.lu@spreadtrum.com>
>> +Description:
>> + Set the pattern generator rise, high, fall and low
>> + times (0..63). It's unit is 0.125s, it should be > 0.
>> +
>> + 1 - 125 ms
>> + 2 - 250 ms
>> + 3 - 375 ms
>> + ...
>> + ...
>> + ...
>> + 62 - 7.75 s
>> + 63 - 7.875 s
>
>
> It would be good to describe here how altering these settings
> interacts with brightness changes. E.g., AFAICS from the code
> the pattern is turned off when setting brightness to 0, and
> turned on when writing any of these files.

Correct. We need set rise, high, fall and low time firstly, then turn
on the LED with setting brightness > 0. Will add more description to
explain how to use them.

>
> I'm also not sure if making these files RO is a good idea.
> How about making them RW? Any brightness change would
> reset those values to 0 and turn off pattern generator.

Sure, will make them RW.

>
> Otherwise it would be not possible to check whether pattern
> generator is enabled or not.
>
>
>> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
>> index 2c896c0..319449b 100644
>> --- a/drivers/leds/Kconfig
>> +++ b/drivers/leds/Kconfig
>> @@ -647,6 +647,17 @@ config LEDS_IS31FL32XX
>> LED controllers. They are I2C devices with multiple
>> constant-current
>> channels, each with independent 256-level PWM control.
>> +config LEDS_SC27XX_BLTC
>> + tristate "LED support for the SC27xx breathing light controller"
>> + depends on LEDS_CLASS && MFD_SC27XX_PMIC
>> + depends on OF
>> + help
>> + Say Y here to include support for the SC27xx breathing light
>> controller
>> + LEDs.
>> +
>> + This driver can also be built as a module. If so the module will
>> be
>> + called leds-sc27xx-bltc.
>> +
>> comment "LED driver for blink(1) USB RGB LED is under Special HID
>> drivers (HID_THINGM)"
>> config LEDS_BLINKM
>> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
>> index 91eca81..ff6917e 100644
>> --- a/drivers/leds/Makefile
>> +++ b/drivers/leds/Makefile
>> @@ -76,6 +76,7 @@ obj-$(CONFIG_LEDS_MLXREG) += leds-mlxreg.o
>> obj-$(CONFIG_LEDS_NIC78BX) += leds-nic78bx.o
>> obj-$(CONFIG_LEDS_MT6323) += leds-mt6323.o
>> obj-$(CONFIG_LEDS_LM3692X) += leds-lm3692x.o
>> +obj-$(CONFIG_LEDS_SC27XX_BLTC) += leds-sc27xx-bltc.o
>> # LED SPI Drivers
>> obj-$(CONFIG_LEDS_DAC124S085) += leds-dac124s085.o
>> diff --git a/drivers/leds/leds-sc27xx-bltc.c
>> b/drivers/leds/leds-sc27xx-bltc.c
>> new file mode 100644
>> index 0000000..61c5b72
>> --- /dev/null
>> +++ b/drivers/leds/leds-sc27xx-bltc.c
>> @@ -0,0 +1,387 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +// Copyright (C) 2018 Spreadtrum Communications Inc.
>> +
>> +#include <linux/leds.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +#include <uapi/linux/uleds.h>
>> +
>> +/* PMIC global control register definition */
>> +#define SC27XX_MODULE_EN0 0xc08
>> +#define SC27XX_CLK_EN0 0xc18
>> +#define SC27XX_RGB_CTRL 0xebc
>> +
>> +#define SC27XX_BLTC_EN BIT(9)
>> +#define SC27XX_RTC_EN BIT(7)
>> +#define SC27XX_RGB_PD BIT(0)
>> +
>> +/* Breathing light controller register definition */
>> +#define SC27XX_LEDS_CTRL 0x00
>> +#define SC27XX_LEDS_PRESCALE 0x04
>> +#define SC27XX_LEDS_DUTY 0x08
>> +#define SC27XX_LEDS_CURVE0 0x0c
>> +#define SC27XX_LEDS_CURVE1 0x10
>> +
>> +#define SC27XX_CTRL_SHIFT 4
>> +#define SC27XX_LED_RUN BIT(0)
>> +#define SC27XX_LED_TYPE BIT(1)
>> +
>> +#define SC27XX_DUTY_SHIFT 8
>> +#define SC27XX_DUTY_MASK GENMASK(15, 0)
>> +#define SC27XX_MOD_MASK GENMASK(7, 0)
>> +
>> +#define SC27XX_CURVE_SHIFT 8
>> +#define SC27XX_CURVE_L_MASK GENMASK(7, 0)
>> +#define SC27XX_CURVE_H_MASK GENMASK(15, 8)
>> +
>> +#define SC27XX_LEDS_OFFSET 0x10
>> +#define SC27XX_LEDS_MAX 3
>> +#define SC27XX_LEDS_TIME_MAX 63
>> +
>> +/*
>> + * The SC27xx breathing light controller can support 3 outputs: red LED,
>> + * green LED and blue LED. Each LED can support normal PWM mode and
>> breathing
>> + * mode.
>> + *
>> + * In breathing mode, the LED output curve includes rise, high, fall and
>> low 4
>> + * stages, and the duration of each stage is configurable.
>> + */
>> +enum sc27xx_led_config {
>> + SC27XX_RISE_TIME,
>> + SC27XX_FALL_TIME,
>> + SC27XX_HIGH_TIME,
>> + SC27XX_LOW_TIME,
>> +};
>> +
>> +struct sc27xx_led {
>> + char name[LED_MAX_NAME_SIZE];
>> + struct led_classdev ldev;
>> + struct sc27xx_led_priv *priv;
>> + enum led_brightness value;
>
> This property is redundant - you have brightness in the
> struct led_classdev.

Yes, will remove this.

>> + u8 line;
>> + bool breath_mode;
>> + bool active;
>> +};
>> +
>> +struct sc27xx_led_priv {
>> + struct sc27xx_led leds[SC27XX_LEDS_MAX];
>> + struct regmap *regmap;
>> + struct mutex lock;
>> + u32 base;
>> +};
>> +
>> +#define to_sc27xx_led(ldev) \
>> + container_of(ldev, struct sc27xx_led, ldev)
>> +
>> +static int sc27xx_led_init(struct regmap *regmap)
>> +{
>> + int err;
>> +
>> + err = regmap_update_bits(regmap, SC27XX_MODULE_EN0,
>> SC27XX_BLTC_EN,
>> + SC27XX_BLTC_EN);
>> + if (err)
>> + return err;
>> +
>> + err = regmap_update_bits(regmap, SC27XX_CLK_EN0, SC27XX_RTC_EN,
>> + SC27XX_RTC_EN);
>> + if (err)
>> + return err;
>> +
>> + return regmap_update_bits(regmap, SC27XX_RGB_CTRL, SC27XX_RGB_PD,
>> 0);
>> +}
>> +
>> +static u32 sc27xx_led_get_offset(struct sc27xx_led *leds)
>> +{
>> + return leds->priv->base + SC27XX_LEDS_OFFSET * leds->line;
>> +}
>> +
>> +static int sc27xx_led_enable(struct sc27xx_led *leds)
>> +{
>> + u32 base = sc27xx_led_get_offset(leds);
>> + u32 ctrl_base = leds->priv->base + SC27XX_LEDS_CTRL;
>> + u8 ctrl_shift = SC27XX_CTRL_SHIFT * leds->line;
>> + struct regmap *regmap = leds->priv->regmap;
>> + int err;
>> +
>> + err = regmap_update_bits(regmap, base + SC27XX_LEDS_DUTY,
>> + SC27XX_DUTY_MASK,
>> + (leds->value << SC27XX_DUTY_SHIFT) |
>> + SC27XX_MOD_MASK);
>> + if (err)
>> + return err;
>> +
>> + if (leds->breath_mode)
>> + return regmap_update_bits(regmap, ctrl_base,
>> + SC27XX_LED_RUN << ctrl_shift,
>> + SC27XX_LED_RUN << ctrl_shift);
>> +
>> + return regmap_update_bits(regmap, ctrl_base,
>> + (SC27XX_LED_RUN | SC27XX_LED_TYPE) << ctrl_shift,
>> + (SC27XX_LED_RUN | SC27XX_LED_TYPE) << ctrl_shift);
>> +}
>> +
>> +static int sc27xx_led_disable(struct sc27xx_led *leds)
>> +{
>> + u8 ctrl_shift = SC27XX_CTRL_SHIFT * leds->line;
>> +
>> + leds->breath_mode = false;
>> +
>> + return regmap_update_bits(leds->priv->regmap,
>> + leds->priv->base + SC27XX_LEDS_CTRL,
>> + (SC27XX_LED_RUN | SC27XX_LED_TYPE) << ctrl_shift,
>> 0);
>> +}
>> +
>> +static int sc27xx_led_set(struct led_classdev *ldev, enum led_brightness
>> value)
>> +{
>> + struct sc27xx_led *leds = to_sc27xx_led(ldev);
>> + int err;
>> +
>> + mutex_lock(&leds->priv->lock);
>
>
> Empty line here please.

OK.

>
>> + leds->value = value;
>
>
> It should not be needed at all.

Yes.

>
>> + if (value == LED_OFF)
>> + err = sc27xx_led_disable(leds);
>> + else
>> + err = sc27xx_led_enable(leds);
>
>
> Empty line here please.

OK.

>
>> + mutex_unlock(&leds->priv->lock);
>> +
>> + return err;
>> +}
>> +
>> +static int sc27xx_led_config(struct sc27xx_led *leds,
>> + enum sc27xx_led_config config, u32 val)
>> +{
>> + u32 base = sc27xx_led_get_offset(leds);
>> + struct regmap *regmap = leds->priv->regmap;
>> + int err;
>> +
>> + mutex_lock(&leds->priv->lock);
>
>
> Empty line here please.

OK.

>
>> + switch (config) {
>> + case SC27XX_RISE_TIME:
>> + err = regmap_update_bits(regmap, base +
>> SC27XX_LEDS_CURVE0,
>> + SC27XX_CURVE_L_MASK, val);
>> + break;
>> + case SC27XX_FALL_TIME:
>> + err = regmap_update_bits(regmap, base +
>> SC27XX_LEDS_CURVE0,
>> + SC27XX_CURVE_H_MASK,
>> + val << SC27XX_CURVE_SHIFT);
>> + break;
>> + case SC27XX_HIGH_TIME:
>> + err = regmap_update_bits(regmap, base +
>> SC27XX_LEDS_CURVE1,
>> + SC27XX_CURVE_L_MASK, val);
>> + break;
>> + case SC27XX_LOW_TIME:
>> + err = regmap_update_bits(regmap, base +
>> SC27XX_LEDS_CURVE1,
>> + SC27XX_CURVE_H_MASK,
>> + val << SC27XX_CURVE_SHIFT);
>> + break;
>> + default:
>> + err = -ENOTSUPP;
>> + break;
>> + }
>> +
>> + if (!err && !leds->breath_mode)
>> + leds->breath_mode = true;
>> +
>> + mutex_unlock(&leds->priv->lock);
>> +
>> + return err;
>> +}
>> +
>> +static ssize_t rise_time_store(struct device *dev,
>> + struct device_attribute *attr,
>> + const char *buf, size_t size)
>> +{
>> + struct led_classdev *ldev = dev_get_drvdata(dev);
>> + struct sc27xx_led *leds = to_sc27xx_led(ldev);
>> + u32 val;
>> + int err;
>> +
>> + if (kstrtou32(buf, 10, &val) || val > SC27XX_LEDS_TIME_MAX)
>> + return -EINVAL;
>> +
>> + err = sc27xx_led_config(leds, SC27XX_RISE_TIME, val);
>> + if (err)
>> + return err;
>> +
>> + return size;
>> +}
>> +
>> +static ssize_t fall_time_store(struct device *dev,
>> + struct device_attribute *attr,
>> + const char *buf, size_t size)
>> +{
>> + struct led_classdev *ldev = dev_get_drvdata(dev);
>> + struct sc27xx_led *leds = to_sc27xx_led(ldev);
>> + u32 val;
>> + int err;
>> +
>> + if (kstrtou32(buf, 10, &val) || val > SC27XX_LEDS_TIME_MAX)
>> + return -EINVAL;
>> +
>> + err = sc27xx_led_config(leds, SC27XX_FALL_TIME, val);
>> + if (err)
>> + return err;
>> +
>> + return size;
>> +}
>> +
>> +static ssize_t high_time_store(struct device *dev,
>> + struct device_attribute *attr,
>> + const char *buf, size_t size)
>> +{
>> + struct led_classdev *ldev = dev_get_drvdata(dev);
>> + struct sc27xx_led *leds = to_sc27xx_led(ldev);
>> + u32 val;
>> + int err;
>> +
>> + if (kstrtou32(buf, 10, &val) || val > SC27XX_LEDS_TIME_MAX)
>> + return -EINVAL;
>> +
>> + err = sc27xx_led_config(leds, SC27XX_HIGH_TIME, val);
>> + if (err)
>> + return err;
>> +
>> + return size;
>> +}
>> +
>> +static ssize_t low_time_store(struct device *dev,
>> + struct device_attribute *attr,
>> + const char *buf, size_t size)
>> +{
>> + struct led_classdev *ldev = dev_get_drvdata(dev);
>> + struct sc27xx_led *leds = to_sc27xx_led(ldev);
>> + u32 val;
>> + int err;
>> +
>> + if (kstrtou32(buf, 10, &val) || val > SC27XX_LEDS_TIME_MAX)
>> + return -EINVAL;
>> +
>> + err = sc27xx_led_config(leds, SC27XX_LOW_TIME, val);
>> + if (err)
>> + return err;
>> +
>> + return size;
>> +}
>> +
>> +static DEVICE_ATTR_WO(rise_time);
>> +static DEVICE_ATTR_WO(fall_time);
>> +static DEVICE_ATTR_WO(high_time);
>> +static DEVICE_ATTR_WO(low_time);
>> +
>> +static struct attribute *sc27xx_led_attrs[] = {
>> + &dev_attr_rise_time.attr,
>> + &dev_attr_fall_time.attr,
>> + &dev_attr_high_time.attr,
>> + &dev_attr_low_time.attr,
>> + NULL,
>> +};
>> +ATTRIBUTE_GROUPS(sc27xx_led);
>> +
>> +static int sc27xx_led_register(struct device *dev, struct sc27xx_led_priv
>> *priv)
>> +{
>> + int i, err;
>> +
>> + err = sc27xx_led_init(priv->regmap);
>> + if (err)
>> + return err;
>> +
>> + for (i = 0; i < SC27XX_LEDS_MAX; i++) {
>> + struct sc27xx_led *led = &priv->leds[i];
>> +
>> + if (!led->active)
>> + continue;
>> +
>> + led->line = i;
>> + led->priv = priv;
>> + led->ldev.name = led->name;
>> + led->ldev.brightness_set_blocking = sc27xx_led_set;
>> + led->ldev.max_brightness = LED_FULL;
>
>
> LED core will set max_brightness to LED_FULL if initialized to 0,
> so we can skip this line.

Sure.

>> + led->ldev.groups = sc27xx_led_groups;
>> +
>> + err = devm_led_classdev_register(dev, &led->ldev);
>> + if (err)
>> + return err;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int sc27xx_led_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device_node *np = dev->of_node, *child;
>> + struct sc27xx_led_priv *priv;
>> + const char *str;
>> + u32 base, count, reg;
>> + int err;
>> +
>> + count = of_get_child_count(np);
>> + if (!count || count > SC27XX_LEDS_MAX)
>> + return -EINVAL;
>> +
>> + err = of_property_read_u32(np, "reg", &base);
>> + if (err) {
>> + dev_err(dev, "fail to get reg of property\n");
>> + return err;
>> + }
>> +
>> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
>> + if (!priv)
>> + return -ENOMEM;
>> +
>> + mutex_init(&priv->lock);
>> + priv->base = base;
>> + priv->regmap = dev_get_regmap(dev->parent, NULL);
>> + if (IS_ERR(priv->regmap)) {
>> + err = PTR_ERR(priv->regmap);
>> + dev_err(dev, "failed to get regmap: %d\n", err);
>> + return err;
>> + }
>> +
>> + for_each_child_of_node(np, child) {
>> + err = of_property_read_u32(child, "reg", &reg);
>> + if (err) {
>> + of_node_put(child);
>
>
> Now we need also mutex_destroy() in the error path, so please add relevant
> label and go there from here.

OK.

>
>> + return err;
>> + }
>> +
>> + if (reg >= SC27XX_LEDS_MAX || priv->leds[reg].active) {
>> + of_node_put(child);
>> + return -EINVAL;
>
>
> Ditto.
>
>
>> + }
>> +
>> + priv->leds[reg].active = true;
>> +
>> + err = of_property_read_string(child, "label", &str);
>> + if (err)
>> + snprintf(priv->leds[reg].name, LED_MAX_NAME_SIZE,
>> + "sc27xx::");
>> + else
>> + snprintf(priv->leds[reg].name, LED_MAX_NAME_SIZE,
>> + "sc27xx:%s", str);
>> + }
>> +
>> + return sc27xx_led_register(dev, priv);
>> +}
>> +
>> +static const struct of_device_id sc27xx_led_of_match[] = {
>> + { .compatible = "sprd,sc2731-bltc", },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(of, sc27xx_led_of_match);
>> +
>> +static struct platform_driver sc27xx_led_driver = {
>> + .driver = {
>> + .name = "sprd-bltc",
>> + .of_match_table = sc27xx_led_of_match,
>> + },
>> + .probe = sc27xx_led_probe,
>
>
> "remove" op will be needed as well for mutex_destroy().

Yes. Thanks for your comments.

--
Baolin.wang
Best Regards

\
 
 \ /
  Last update: 2018-05-09 04:35    [W:0.143 / U:0.304 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site