lkml.org 
[lkml]   [2018]   [May]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v7 00/13] Intel Processor Trace virtualization enabling
Date
> Hi All,
>
> Here is a patch-series which adding Processor Trace enabling in KVM guest. You can get It's software developer manuals from:
> https://software.intel.com/sites/default/files/managed/c5/15/architecture-instruction-set-extensions-programming-reference.pdf
> In Chapter 4 INTEL PROCESSOR TRACE: VMX IMPROVEMENTS.
>
> Introduction:
> Intel Processor Trace (Intel PT) is an extension of Intel Architecture that captures information about software execution using
> dedicated hardware facilities that cause only minimal performance perturbation to the software being traced. Details on the Intel PT
> infrastructure and trace capabilities can be found in the Intel 64 and IA-32 Architectures Software Developer’s Manual, Volume 3C.
>
> The suite of architecture changes serve to simplify the process of virtualizing Intel PT for use by a guest software. There are two
> primary elements to this new architecture support for VMX support improvements made for Intel PT.
> 1. Addition of a new guest IA32_RTIT_CTL value field to the VMCS.
> — This serves to speed and simplify the process of disabling trace on VM exit, and restoring it on VM entry.
> 2. Enabling use of EPT to redirect PT output.
> — This enables the VMM to elect to virtualize the PT output buffer using EPT. In this mode, the CPU will treat PT output addresses
> as Guest Physical Addresses (GPAs) and translate them using EPT. This means that Intel PT output reads (of the ToPA table) and
> writes (of trace output) can cause EPT violations, and other output events.
>
> Processor Trace virtualization can be work in one of 3 possible modes by set new option "pt_mode". Default value is system mode.
> a. system-wide: trace both host/guest and output to host buffer; b. host-only: only trace host and output to host buffer; c. host-
> guest: trace host/guest simultaneous and output to their respective buffer.
>
> >From V6:
> - split pathes 1~2 to four separate patches (these patches do 2 things) and add more descriptions.
>
> >From V5:
> - rename the function from pt_cap_get_ex() to __pt_cap_get();
> - replace the most of function from vmx_pt_supported() to "pt_mode == PT_MODE_HOST_GUEST"(or !=).
>
> >From V4:
> - add data check when setting the value of MSR_IA32_RTIT_CTL;
> - Invoke new interface to set the intercept of MSRs read/write after "MSR bitmap per-vcpu" patches.
>
> >From V3:
> - change default mode to SYSTEM mode;
> - add a new patch to move PT out of scattered features;
> - add a new fucntion kvm_get_pt_addr_cnt() to get the number of address ranges;
> - add a new function vmx_set_rtit_ctl() to set the value of guest RTIT_CTL, GUEST_IA32_RTIT_CTL and MSRs intercept.
>
> >From v2:
> - replace *_PT_SUPPRESS_PIP to *_PT_CONCEAL_PIP;
> - clean SECONDARY_EXEC_PT_USE_GPA, VM_EXIT_CLEAR_IA32_RTIT_CTL and VM_ENTRY_LOAD_IA32_RTIT_CTL in SYSTEM mode.
> These bits must be all set or all clean;
> - move processor tracing out of scattered features;
> - add a new function to enable/disable intercept MSRs read/write;
> - add all Intel PT MSRs read/write and disable intercept when PT is enabled in guest;
> - disable Intel PT and enable intercept MSRs when L1 guest VMXON;
> - performance optimization.
> In Host only mode. we just need to save host RTIT_CTL before vm-entry and restore host RTIT_CTL after vm-exit;
> In HOST_GUEST mode. we need to save and restore all MSRs only when PT has enabled in guest.
> - use XSAVES/XRESTORES implement context switch.
> Haven't implementation in this version and still in debuging. will make a separate patch work on this.
>
> >From v1:
> - remove guest-only mode because guest-only mode can be covered by host-guest mode;
> - always set "use GPA for processor tracing" in secondary execution control if it can be;
> - trap RTIT_CTL read/write. Forbid write this msr when VMXON in L1 hypervisor.
>
> Chao Peng (8):
> perf/x86/intel/pt: Move Intel-PT MSRs bit definitions to a public
> header
> perf/x86/intel/pt: Change pt_cap_get() to a public function
> KVM: x86: Add Intel Processor Trace virtualization mode
> KVM: x86: Add Intel Processor Trace cpuid emulation
> KVM: x86: Add Intel processor trace context for each vcpu
> KVM: x86: Implement Intel Processor Trace context switch
> KVM: x86: Implement Intel Processor Trace MSRs read/write
> KVM: x86: Set intercept for Intel PT MSRs read/write
>
> Luwei Kang (5):
> perf/x86/intel/pt: Add new bit definitions for Intel PT MSRs
> perf/x86/intel/pt: add new capability for Intel PT
> perf/x86/intel/pt: Introduce a new function to get capability of Intel
> PT
> KVM: x86: Introduce a function to initialize the PT configuration
> KVM: x86: Disable Intel Processor Trace when VMXON in L1 guest
>
> arch/x86/events/intel/pt.c | 12 +-
> arch/x86/events/intel/pt.h | 58 ------
> arch/x86/include/asm/intel_pt.h | 40 ++++
> arch/x86/include/asm/kvm_host.h | 1 +
> arch/x86/include/asm/msr-index.h | 38 ++++
> arch/x86/include/asm/vmx.h | 8 +
> arch/x86/kvm/cpuid.c | 22 ++-
> arch/x86/kvm/svm.c | 6 +
> arch/x86/kvm/vmx.c | 412 ++++++++++++++++++++++++++++++++++++++-
> arch/x86/kvm/x86.c | 33 +++-
> 10 files changed, 563 insertions(+), 67 deletions(-)
>

Send this patch set twice because path 2 send fail in the first time.

Thanks,
Luwei Kang
\
 
 \ /
  Last update: 2018-05-03 12:25    [W:0.262 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site