lkml.org 
[lkml]   [2018]   [May]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[GIT PULL] SCSI fixes for 4.17-rc3
From
Date
Three small bug fixes: an illegally overlapping memcmp in target code,
a potential infinite loop in isci under certain rare phy conditions and
an ATA queue depth (performance) correction for storvsc.

The patch is available here:

git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi.git scsi-fixes

The short changelog is:

Bryant G Ly (1):
scsi: target: Fix fortify_panic kernel exception

Colin Ian King (1):
scsi: isci: Fix infinite loop in while loop

Long Li (1):
scsi: storvsc: Set up correct queue depth values for IDE devices

And the diffstat:

drivers/scsi/isci/port_config.c | 3 +--
drivers/scsi/storvsc_drv.c | 7 +++++--
drivers/target/target_core_iblock.c | 8 ++++----
3 files changed, 10 insertions(+), 8 deletions(-)

With full diff below.

James

---

diff --git a/drivers/scsi/isci/port_config.c b/drivers/scsi/isci/port_config.c
index edb7be786c65..9e8de1462593 100644
--- a/drivers/scsi/isci/port_config.c
+++ b/drivers/scsi/isci/port_config.c
@@ -291,7 +291,7 @@ sci_mpc_agent_validate_phy_configuration(struct isci_host *ihost,
* Note: We have not moved the current phy_index so we will actually
* compare the startting phy with itself.
* This is expected and required to add the phy to the port. */
- while (phy_index < SCI_MAX_PHYS) {
+ for (; phy_index < SCI_MAX_PHYS; phy_index++) {
if ((phy_mask & (1 << phy_index)) == 0)
continue;
sci_phy_get_sas_address(&ihost->phys[phy_index],
@@ -311,7 +311,6 @@ sci_mpc_agent_validate_phy_configuration(struct isci_host *ihost,
&ihost->phys[phy_index]);

assigned_phy_mask |= (1 << phy_index);
- phy_index++;
}

}
diff --git a/drivers/scsi/storvsc_drv.c b/drivers/scsi/storvsc_drv.c
index 8c51d628b52e..a2ec0bc9e9fa 100644
--- a/drivers/scsi/storvsc_drv.c
+++ b/drivers/scsi/storvsc_drv.c
@@ -1722,11 +1722,14 @@ static int storvsc_probe(struct hv_device *device,
max_targets = STORVSC_MAX_TARGETS;
max_channels = STORVSC_MAX_CHANNELS;
/*
- * On Windows8 and above, we support sub-channels for storage.
+ * On Windows8 and above, we support sub-channels for storage
+ * on SCSI and FC controllers.
* The number of sub-channels offerred is based on the number of
* VCPUs in the guest.
*/
- max_sub_channels = (num_cpus / storvsc_vcpus_per_sub_channel);
+ if (!dev_is_ide)
+ max_sub_channels =
+ (num_cpus - 1) / storvsc_vcpus_per_sub_channel;
}

scsi_driver.can_queue = (max_outstanding_req_per_channel *
diff --git a/drivers/target/target_core_iblock.c b/drivers/target/target_core_iblock.c
index 07c814c42648..60429011292a 100644
--- a/drivers/target/target_core_iblock.c
+++ b/drivers/target/target_core_iblock.c
@@ -427,8 +427,8 @@ iblock_execute_zero_out(struct block_device *bdev, struct se_cmd *cmd)
{
struct se_device *dev = cmd->se_dev;
struct scatterlist *sg = &cmd->t_data_sg[0];
- unsigned char *buf, zero = 0x00, *p = &zero;
- int rc, ret;
+ unsigned char *buf, *not_zero;
+ int ret;

buf = kmap(sg_page(sg)) + sg->offset;
if (!buf)
@@ -437,10 +437,10 @@ iblock_execute_zero_out(struct block_device *bdev, struct se_cmd *cmd)
* Fall back to block_execute_write_same() slow-path if
* incoming WRITE_SAME payload does not contain zeros.
*/
- rc = memcmp(buf, p, cmd->data_length);
+ not_zero = memchr_inv(buf, 0x00, cmd->data_length);
kunmap(sg_page(sg));

- if (rc)
+ if (not_zero)
return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE;

ret = blkdev_issue_zeroout(bdev,
\
 
 \ /
  Last update: 2018-05-02 16:54    [W:0.027 / U:1.448 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site