lkml.org 
[lkml]   [2018]   [May]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v5 00/14] mmc: sdhci-omap: Add UHS/HS200 mode support
On 27 April 2018 at 13:47, Kishon Vijay Abraham I <kishon@ti.com> wrote:
> Add UHS/HS200 mode support in sdhci-omap. The programming sequence
> for voltage switching, tuning is followed from AM572x TRM
> http://www.ti.com/lit/ug/spruhz6j/spruhz6j.pdf
> (Similar to all AM57x/DRA7x SoCs). The patch series also implements
> workaround for errata published in
> http://www.ti.com/lit/er/sprz429l/sprz429l.pdf
>
> patches are created on top of
> git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc.git next
>
> The patches along with dt has also been pushed to
> https://github.com/kishon/linux-wip.git sdhci_uhs_v5

Thanks, applied for next!

Kind regards
Uffe

>
> Changes from v4:
> *) Added comment in sdhci for disabling HS200/HS400 mode
> *) Fixed a couple of chunks in "Program a relatively accurate SW timeout
> value" which were missed in the previous revision
> *) Added a patch in sdhci-omap to get IODelay values of 3.3v DDR mode.
> *) Added pinctrl binding documentation for sdhci-omap which was missed
> before.
>
> Changes from v3:
> *) Fixed Adrian's comment on error handling when __sdhci_add_host()
> fails
> *) Used Adrian's patches for programming SW timeout value.
>
> Changes from v2:
> *) Patches in v2 already applied to mmc -next are dropped from the
> series.
> *) Changed SW timeout logic as per Adrians's suggestion
> *) Validated SDIO with the current patches (added a couple of fixes
> found while adding SDIO support).
> *) Used soc_device_match() instead of pdata-quirks as per Tony's
> suggestions.
>
> Changes from v1:
> *) Only poll on DAT0 and DATI for card_busy status
> *) Cleanup iodelay patch as suggested by Tony.
> *) Added quirk to disable HW timeout
> *) Use the existing data timer but program a relatively accurate
> SW timeout value (Impacts all platforms)
> *) Fix a bug in sdhci which was using data_timer for non data line
> commands
>
> Adrian Hunter (2):
> mmc: sdhci: Add quirk to disable HW timeout
> mmc: sdhci: Factor out target_timeout calculation
>
> Kishon Vijay Abraham I (12):
> mmc: sdhci-omap: Fix when capabilities are obtained from
> SDHCI_CAPABILITIES reg
> mmc: sdhci-omap: Remove setting ADMA capability in driver
> mmc: sdhci-omap: Workaround for Errata i843
> mmc: sdhci-omap: Invoke sdhci_get_of_property to read sdhci dt
> properties
> mmc: sdhci: Disable 1.8v modes (HS200/HS400/UHS) if controller can't
> support 1.8v
> mmc: sdhci: Program a relatively accurate SW timeout value
> mmc: sdhci-omap: Workaround for Errata i834
> dt-bindings: sdhci-omap: Add K2G specific binding
> mmc: sdhci-omap: Add support for MMC/SD controller in k2g SoC
> mmc: sdhci-omap: Add sdhci_omap specific ops for enable_sdio_irq
> dt-bindings: sdhci-omap: Add pinctrl bindings
> mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode
>
> .../devicetree/bindings/mmc/sdhci-omap.txt | 7 +
> drivers/mmc/host/sdhci-omap.c | 92 +++++++++--
> drivers/mmc/host/sdhci.c | 148 ++++++++++++++----
> drivers/mmc/host/sdhci.h | 15 ++
> include/linux/mmc/host.h | 4 +
> 5 files changed, 226 insertions(+), 40 deletions(-)
>
> --
> 2.17.0
>

\
 
 \ /
  Last update: 2018-05-02 15:15    [W:0.132 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site