lkml.org 
[lkml]   [2018]   [May]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC net-next 4/5] net: phy: Add support for IEEE standard test modes
From
Date
On 05/01/2018 10:29 AM, Woojung.Huh@microchip.com wrote:
> Hi Florian,
>
>> diff --git a/drivers/net/phy/phy-tests.c b/drivers/net/phy/phy-tests.c
> ...
>> +/* genphy_set_test - Make a PHY enter one of the standard IEEE defined
>> + * test modes
>> + * @phydev: the PHY device instance
>> + * @test: the desired test mode
>> + * @data: test specific data (none)
>> + *
>> + * This function makes the designated @phydev enter the desired standard
>> + * 100BaseT2 or 1000BaseT test mode as defined in IEEE 802.3-2012 section TWO
>> + * and THREE under 32.6.1.2.1 and 40.6.1.1.2 respectively
>> + */
>> +int genphy_set_test(struct phy_device *phydev,
>> + struct ethtool_phy_test *test, const u8 *data)
>> +{
>> + u16 shift, base, bmcr = 0;
>> + int ret;
>> +
>> + /* Exit test mode */
>> + if (test->mode == PHY_STD_TEST_MODE_NORMAL) {
>> + ret = phy_read(phydev, MII_CTRL1000);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret &= ~GENMASK(15, 13);
>> +
>> + return phy_write(phydev, MII_CTRL1000, ret);
>> + }
>> +
>> + switch (test->mode) {
>> + case PHY_STD_TEST_MODE_100BASET2_1:
>> + case PHY_STD_TEST_MODE_100BASET2_2:
>> + case PHY_STD_TEST_MODE_100BASET2_3:
>> + if (!(phydev->supported & PHY_100BT_FEATURES))
>> + return -EOPNOTSUPP;
>> +
>> + shift = 14;
>> + base = test->mode - PHY_STD_TEST_MODE_NORMAL;
>> + bmcr = BMCR_SPEED100;
>> + break;
>> +
>> + case PHY_STD_TEST_MODE_1000BASET_1:
>> + case PHY_STD_TEST_MODE_1000BASET_2:
>> + case PHY_STD_TEST_MODE_1000BASET_3:
>> + case PHY_STD_TEST_MODE_1000BASET_4:
>> + if (!(phydev->supported & PHY_1000BT_FEATURES))
>> + return -EOPNOTSUPP;
>> +
>> + shift = 13;
>> + base = test->mode - PHY_STD_TEST_MODE_100BASET2_MAX;
>> + bmcr = BMCR_SPEED1000;
>> + break;
>> +
>> + default:
>> + /* Let an upper driver deal with additional modes it may
>> + * support
>> + */
>> + return -EOPNOTSUPP;
>> + }
>> +
>> + /* Force speed and duplex */
>> + ret = phy_write(phydev, MII_BMCR, bmcr | BMCR_FULLDPLX);
>> + if (ret < 0)
>> + return ret;
>> +
>> + /* Set the desired test mode bit */
>> + return phy_write(phydev, MII_CTRL1000, (test->mode + base) << shift);
>> +}
> For now, these are for 100B-T2 & 1000B-TX.
> But, other speeds such as 802.3bw/bq/cq have very similar format,
> how about make phy_write() to BMCR & CTRL1000 as another function call per speed?

Not sure I completely understand your suggestion, do you mean that I
should break down the body of that function above such that there are
per-speed lower level functions? Something like the pseudo-code below:

genphy_set_test() {
switch (mode) {
case PHY_STD_TEST_MODE_100BASET2_1:
..
case PHY_STD_TEST_MODE_100BASET2_3:
return genphy_set_100baset2();

case PHY_STD_TEST_MODE_1000BASET_1:
..
case PHY_STD_TEST_MODE_1000BASET_4:
return genphy_set_1000baset();

case PHY_STD_TEST_MODE_8021BWQCQ_1:
return genphy_set_100baset1();

}

Or did you want to see a different way of mapping a given speed/feature
set to a specific test function?
--
Florian

\
 
 \ /
  Last update: 2018-05-01 20:44    [W:0.271 / U:0.436 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site