lkml.org 
[lkml]   [2018]   [Apr]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 6/7] dt-bindings: phy-qcom-usb2: Add support to override tuning values
On Thu, Mar 29, 2018 at 01:38:23PM -0700, Doug Anderson wrote:
> Hi,
>
> On Thu, Mar 29, 2018 at 4:04 AM, Manu Gautam <mgautam@codeaurora.org> wrote:
> > To improve eye diagram for PHYs on different boards of same SOC,
> > some parameters may need to be changed. Provide device tree
> > properties to override these from board specific device tree
> > files. While at it, replace "qcom,qusb2-v2-phy" with compatible
> > string for USB2 PHY on sdm845 which was earlier added for
> > sdm845 only.
> >
> > Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
> > ---
> > .../devicetree/bindings/phy/qcom-qusb2-phy.txt | 19 ++++++++++++++++++-
> > 1 file changed, 18 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> > index 42c9742..0ed140a 100644
> > --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> > +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> > @@ -6,7 +6,7 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
> > Required properties:
> > - compatible: compatible list, contains
> > "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
> > - "qcom,qusb2-v2-phy" for QUSB2 V2 PHY.
> > + "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845.
> >
> > - reg: offset and length of the PHY register set.
> > - #phy-cells: must be 0.
> > @@ -27,6 +27,23 @@ Optional properties:
> > tuning parameter value for qusb2 phy.
> >
> > - qcom,tcsr-syscon: Phandle to TCSR syscon register region.
>
> Just to confirm: the new properties below work just fine on the old
> msm8996 PHY too, right?
>
>
> > + - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be
> > + added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
> > + tuning paramter that may vary for different boards of same SOC.
> > + - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX
> > + output current. 0x0 value corresponding to 24mA which is maximum
> > + current and 0xf corresponds to lowest current which is 15mA.
> > + - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level.
> > + Possible values are:
> > + 00: NONE
> > + 01: +5%
> > + 10: +10%
> > + 11: +15%
>
> The user of the device tree will expect to specify this in decimal,
> right? So list the above as 0, 1, 2, 3. ...not 00, 01, 10, 11.
> (though below I suggest that specifying 0, 1, 2, 3 is probably not
> quite the right way to describe this property).
>
>
> > +- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX
> > + pre-emphasis (specified using qcom,preemphasis-level) must be in
> > + effect. Possible values are:
> > + 0: Full-bit width
> > + 1: Half-bit width
>
> Perhaps just make this a boolean property. If it exists then you get
> the non-default case. AKA: if the default is full bit width, then
> you'd allow a boolean property "qcom,preemphasis-half-width" to
> override. If the default is half bit width then you'd allow
> "qcom,preemphasis-full-width" to override.
>
>
> For all the above optional bits, please indicate what the default is
> if they aren't specified. If you have to specify a different default
> for sdm845 vs. msm8996 then so be it (though it would be nice to avoid
> it by changing the default for sdm845 unless that's totally crazy).
>
>
> Overall this looks pretty good to me. Certainly the descriptions are
> very understandable and this will make tuning on a per-board /
> per-port basis much easier! Thanks!
>
>
> One last overall comment is that ideally we could make the device tree
> a little bit more human readable. Right now we'll have a set of
> properties that looks like this (numbers made up):
>
> qcom,imp-res-offset-value = <0x13>;
> qcom,hstx-trim-value = <0x7>;
> qcom,preemphasis-level = <1>;
> qcom,preemphasis-width = <0>;
>
>
> One option to make that more readable would be to change the units, AKA:
>
> qcom,hstx-trim-ma = <18>;
> qcom,preemphasis-percent = <5>;
>
> ...then the code would translate from these human-readable values to
> the real numbers.

Yes, we often do that. However, there properties are very specific to
this device and making the driver translate back to h/w values doesn't
add much.

> Another option would be to add a #include to the bindings. I'd defer
> to the wisdom of the bindings guys about if this is better or worse
> than adding the units, but personally I like it better because:
> * You get a compile-time error if you use an unsupported value.
> * You don't need to add the code to translate.

This is fine for me. Really, I'm fine with it as-is, but #defines make
some people happy.

Rob

\
 
 \ /
  Last update: 2018-04-09 22:18    [W:2.028 / U:1.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site