lkml.org 
[lkml]   [2018]   [Apr]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH AUTOSEL for 4.15 086/189] igb: Allow to remove administratively set MAC on VFs
    Date
    From: Corinna Vinschen <vinschen@redhat.com>

    [ Upstream commit 177132df5e45b134c147f419f567a3b56aafaf2b ]

    Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
    for use by a virtual machine (either using vfio device assignment or
    macvtap passthru mode), it saves the current MAC address and vlan tag
    so that it can reset them to their original value when the guest is
    done. Libvirt can't leave the VF MAC set to the value used by the
    now-defunct guest since it may be started again later using a
    different VF, but it certainly shouldn't just pick any random value,
    either. So it saves the state of everything prior to using the VF, and
    resets it to that.

    The igb driver initializes the MAC addresses of all VFs to
    00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
    netlink message, also visible in the list of VFs in the output of "ip
    link show"). But when libvirt attempts to restore the MAC address back
    to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
    responds with "Invalid argument".

    Forbidding a reset back to the original value leaves the VF MAC at the
    value set for the now-defunct virtual machine. Especially on a system
    with NetworkManager enabled, this has very bad consequences, since
    NetworkManager forces all interfacess to be IFF_UP all the time - if
    the same virtual machine is restarted using a different VF (or even on
    a different host), there will be multiple interfaces watching for
    traffic with the same MAC address.

    To allow libvirt to revert to the original state, we need a way to
    remove the administrative set MAC on a VF, to allow normal host
    operation again, and to reset/overwrite the VF MAC via VF netdev.

    This patch implements the outlined scenario by allowing to set the
    VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
    igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
    so it's possible to reset the VF MAC back to the original value via
    the VF netdev.

    Note: Recent patches to libvirt allow for a workaround if the NIC
    isn't capable of resetting the administrative MAC back to all 0, but
    in theory the NIC should allow resetting the MAC in the first place.

    Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
    Tested-by: Aaron Brown <arron.f.brown@intel.com>
    Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
    Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
    ---
    drivers/net/ethernet/intel/igb/igb_main.c | 42 +++++++++++++++++++++++--------
    1 file changed, 31 insertions(+), 11 deletions(-)

    diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c
    index c69a5b3ae8c8..13dd7d2d90fe 100644
    --- a/drivers/net/ethernet/intel/igb/igb_main.c
    +++ b/drivers/net/ethernet/intel/igb/igb_main.c
    @@ -8718,7 +8718,8 @@ static void igb_rar_set_index(struct igb_adapter *adapter, u32 index)

    /* Indicate to hardware the Address is Valid. */
    if (adapter->mac_table[index].state & IGB_MAC_STATE_IN_USE) {
    - rar_high |= E1000_RAH_AV;
    + if (is_valid_ether_addr(addr))
    + rar_high |= E1000_RAH_AV;

    if (hw->mac.type == e1000_82575)
    rar_high |= E1000_RAH_POOL_1 *
    @@ -8756,17 +8757,36 @@ static int igb_set_vf_mac(struct igb_adapter *adapter,
    static int igb_ndo_set_vf_mac(struct net_device *netdev, int vf, u8 *mac)
    {
    struct igb_adapter *adapter = netdev_priv(netdev);
    - if (!is_valid_ether_addr(mac) || (vf >= adapter->vfs_allocated_count))
    +
    + if (vf >= adapter->vfs_allocated_count)
    + return -EINVAL;
    +
    + /* Setting the VF MAC to 0 reverts the IGB_VF_FLAG_PF_SET_MAC
    + * flag and allows to overwrite the MAC via VF netdev. This
    + * is necessary to allow libvirt a way to restore the original
    + * MAC after unbinding vfio-pci and reloading igbvf after shutting
    + * down a VM.
    + */
    + if (is_zero_ether_addr(mac)) {
    + adapter->vf_data[vf].flags &= ~IGB_VF_FLAG_PF_SET_MAC;
    + dev_info(&adapter->pdev->dev,
    + "remove administratively set MAC on VF %d\n",
    + vf);
    + } else if (is_valid_ether_addr(mac)) {
    + adapter->vf_data[vf].flags |= IGB_VF_FLAG_PF_SET_MAC;
    + dev_info(&adapter->pdev->dev, "setting MAC %pM on VF %d\n",
    + mac, vf);
    + dev_info(&adapter->pdev->dev,
    + "Reload the VF driver to make this change effective.");
    + /* Generate additional warning if PF is down */
    + if (test_bit(__IGB_DOWN, &adapter->state)) {
    + dev_warn(&adapter->pdev->dev,
    + "The VF MAC address has been set, but the PF device is not up.\n");
    + dev_warn(&adapter->pdev->dev,
    + "Bring the PF device up before attempting to use the VF device.\n");
    + }
    + } else {
    return -EINVAL;
    - adapter->vf_data[vf].flags |= IGB_VF_FLAG_PF_SET_MAC;
    - dev_info(&adapter->pdev->dev, "setting MAC %pM on VF %d\n", mac, vf);
    - dev_info(&adapter->pdev->dev,
    - "Reload the VF driver to make this change effective.");
    - if (test_bit(__IGB_DOWN, &adapter->state)) {
    - dev_warn(&adapter->pdev->dev,
    - "The VF MAC address has been set, but the PF device is not up.\n");
    - dev_warn(&adapter->pdev->dev,
    - "Bring the PF device up before attempting to use the VF device.\n");
    }
    return igb_set_vf_mac(adapter, vf, mac);
    }
    --
    2.15.1
    \
     
     \ /
      Last update: 2018-04-09 05:57    [W:4.128 / U:0.040 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site