lkml.org 
[lkml]   [2018]   [Apr]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 3/7] MIPS: perf: Use correct VPE ID when setting up VPE tracing
Date
There are a couple of FIXME's in the perf code which state that
cpu_data[event->cpu].vpe_id reports 0 for both CPUs. This is no longer
the case, since the vpe_id is used extensively by SMP CPS.

VPE local counting gets around this by using smp_processor_id() instead.
As it happens this does work correctly to count events on the right VPE,
but relies on 2 assumptions:
a) Always having 2 VPEs / core.
b) The hardware only paying attention to the least significant bit of
the PERFCTL.VPEID field.
If either of these assumptions change then the incorrect VPEs events
will be counted.

Fix this by replacing smp_processor_id() with
cpu_vpe_id(&current_cpu_data), in the vpe_id() macro, and pass vpe_id()
to M_PERFCTL_VPEID() when setting up PERFCTL.VPEID. The FIXME's can also
be removed since they no longer apply.

Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
---

Changes in v3: None
Changes in v2: None

arch/mips/kernel/perf_event_mipsxx.c | 12 ++----------
1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/arch/mips/kernel/perf_event_mipsxx.c b/arch/mips/kernel/perf_event_mipsxx.c
index 0595a974bc81..7e2b7d38a774 100644
--- a/arch/mips/kernel/perf_event_mipsxx.c
+++ b/arch/mips/kernel/perf_event_mipsxx.c
@@ -135,12 +135,8 @@ static DEFINE_RWLOCK(pmuint_rwlock);
#define vpe_id() (cpu_has_mipsmt_pertccounters ? \
0 : (smp_processor_id() & MIPS_CPUID_TO_COUNTER_MASK))
#else
-/*
- * FIXME: For VSMP, vpe_id() is redefined for Perf-events, because
- * cpu_data[cpuid].vpe_id reports 0 for _both_ CPUs.
- */
#define vpe_id() (cpu_has_mipsmt_pertccounters ? \
- 0 : smp_processor_id())
+ 0 : cpu_vpe_id(&current_cpu_data))
#endif

/* Copied from op_model_mipsxx.c */
@@ -1277,11 +1273,7 @@ static void check_and_calc_range(struct perf_event *event,
*/
hwc->config_base |= M_TC_EN_ALL;
} else {
- /*
- * FIXME: cpu_data[event->cpu].vpe_id reports 0
- * for both CPUs.
- */
- hwc->config_base |= M_PERFCTL_VPEID(event->cpu);
+ hwc->config_base |= M_PERFCTL_VPEID(vpe_id());
hwc->config_base |= M_TC_EN_VPE;
}
} else
--
2.7.4
\
 
 \ /
  Last update: 2018-04-20 12:26    [W:3.288 / U:0.764 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site