lkml.org 
[lkml]   [2018]   [Apr]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH] gpio: dwapb: Add support for 32 interrupts
Date
Hi Rob,

On 09 April 2018 20:20 Rob Herring wrote:
> On Wed, Mar 28, 2018 at 03:22:30PM +0100, Phil Edworthy wrote:
> > The DesignWare GPIO IP can be configured for either 1 or 32
> > interrupts, but the driver currently only supports 1 interrupt. See
> > the DesignWare DW_apb_gpio Databook description of the
> 'GPIO_INTR_IO' parameter.
>
> Someday h/w designers will realize this does nothing to optimize interrupt
> handling...
I can imagine some software where the isr is written to handle a specific GPIO
interrupt _could_ be faster, though no sane software would be designed like
that.

> > This change allows the driver to work with up to 32 interrupts, it
> > will get as many interrupts as specified in the DT 'interrupts' property.
> > It doesn't do anything clever with the different interrupts, it just
> > calls the same handler used for single interrupt hardware.
> >
> > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
> > ---
> > Note: There are a few lines over 80 chars, but this is just guidance, right?
> > Especially as there are already some lines over 80 chars.
>
> Code, yes, but not for paragraphs of text in DT bindings.
Good, that's what I did.

> > ---
> > .../devicetree/bindings/gpio/snps-dwapb-gpio.txt | 10 ++++-
> > drivers/gpio/gpio-dwapb.c | 44 +++++++++++++++++-----
> > include/linux/platform_data/gpio-dwapb.h | 3 +-
> > 3 files changed, 45 insertions(+), 12 deletions(-)
> >
> > diff --git
> > a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt
> > b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt
> > index 4a75da7..e343581 100644
> > --- a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt
> > +++ b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt
> > @@ -26,8 +26,14 @@ controller.
> > the second encodes the triger flags encoded as described in
> >
> > Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> > - interrupt-parent : The parent interrupt controller.
> > -- interrupts : The interrupt to the parent controller raised when
> > GPIOs
> > - generate the interrupts.
> > +- interrupts : The interrupts to the parent controller raised when
> > +GPIOs
> > + generate the interrupts. If the controller provides one combined
> > +interrupt
> > + for all GPIOs, specify a single interrupt. If the controller
> > +provides one
> > + interrupt for each GPIO, provide a list of interrupts that
> > +correspond to each
> > + of the GPIO pins. When specifying multiple interrupts, if any of
> > +the GPIOs are
> > + not connected to an interrupt, use the interrupt-mask property.
> > +- interrupt-mask : a 32-bit bit mask that specifies which interrupts
> > +in the list
> > + of interrupts is valid, bit is 1 for a valid irq.
>
> This is not a standard property and would need a vendor prefix. However, I'd
> prefer you just skip any not connected interrupts with an invalid interrupt
> number. Then the GPIO number is the index into "interrupts".
Makes sense, I'll rework it to do this.

> > - snps,nr-gpios : The number of pins in the port, a single cell.
>
> This BTW should be deprecated to use "nr-gpios" instead, but that's another
> patch.

Thanks for your comments,
Phil

\
 
 \ /
  Last update: 2018-04-10 08:25    [W:0.125 / U:0.424 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site