lkml.org 
[lkml]   [2018]   [Mar]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [v3,4/4] watchdog: add Gateworks System Controller support
On Thu, Mar 29, 2018 at 06:07:57PM -0700, Guenter Roeck wrote:
> On Wed, Mar 28, 2018 at 08:14:03AM -0700, Tim Harvey wrote:
> > Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> > ---
> > drivers/watchdog/Kconfig | 10 ++++
> > drivers/watchdog/Makefile | 1 +
> > drivers/watchdog/gsc_wdt.c | 146 +++++++++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 157 insertions(+)
> > create mode 100644 drivers/watchdog/gsc_wdt.c
> >
> > diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> > index ca200d1..c9d4b2e 100644
> > --- a/drivers/watchdog/Kconfig
> > +++ b/drivers/watchdog/Kconfig
> > @@ -150,6 +150,16 @@ config GPIO_WATCHDOG_ARCH_INITCALL
> > arch_initcall.
> > If in doubt, say N.
> >
> > +config GSC_WATCHDOG
> > + tristate "Gateworks System Controller (GSC) Watchdog support"
> > + depends on MFD_GATEWORKS_GSC
> > + select WATCHDOG_CORE
> > + help
> > + Say Y here to include support for the GSC Watchdog.
> > +
> > + This driver can also be built as a module. If so the module
> > + will be called gsc_wdt.
> > +
> > config MENF21BMC_WATCHDOG
> > tristate "MEN 14F021P00 BMC Watchdog"
> > depends on MFD_MENF21BMC || COMPILE_TEST
> > diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> > index 715a210..499327e 100644
> > --- a/drivers/watchdog/Makefile
> > +++ b/drivers/watchdog/Makefile
> > @@ -215,6 +215,7 @@ obj-$(CONFIG_DA9055_WATCHDOG) += da9055_wdt.o
> > obj-$(CONFIG_DA9062_WATCHDOG) += da9062_wdt.o
> > obj-$(CONFIG_DA9063_WATCHDOG) += da9063_wdt.o
> > obj-$(CONFIG_GPIO_WATCHDOG) += gpio_wdt.o
> > +obj-$(CONFIG_GSC_WATCHDOG) += gsc_wdt.o
> > obj-$(CONFIG_TANGOX_WATCHDOG) += tangox_wdt.o
> > obj-$(CONFIG_WDAT_WDT) += wdat_wdt.o
> > obj-$(CONFIG_WM831X_WATCHDOG) += wm831x_wdt.o
> > diff --git a/drivers/watchdog/gsc_wdt.c b/drivers/watchdog/gsc_wdt.c
> > new file mode 100644
> > index 0000000..b43d083
> > --- /dev/null
> > +++ b/drivers/watchdog/gsc_wdt.c
> > @@ -0,0 +1,146 @@
> > +/* SPDX-License-Identifier: GPL-2.0
> > + *
> > + * Copyright (C) 2018 Gateworks Corporation
> > + *
> > + * This driver registers a Linux Watchdog for the GSC
> > + */
> > +#include <linux/mfd/gsc.h>
> > +#include <linux/module.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/watchdog.h>
> > +
> > +#define WDT_DEFAULT_TIMEOUT 60
> > +
> > +struct gsc_wdt {
> > + struct watchdog_device wdt_dev;
> > + struct gsc_dev *gsc;
> > +};
> > +
> > +static int gsc_wdt_start(struct watchdog_device *wdd)
> > +{
> > + struct gsc_wdt *wdt = watchdog_get_drvdata(wdd);
> > + unsigned int reg = (1 << GSC_CTRL_1_WDT_ENABLE);
>
> Please use BIT().
>
> > + int ret;
> > +
> > + dev_dbg(wdd->parent, "%s timeout=%d\n", __func__, wdd->timeout);
>
> I don't think those debug messages add any value.
>
> > +
> > + /* clear first as regmap_update_bits will not write if no change */
> > + ret = regmap_update_bits(wdt->gsc->regmap, GSC_CTRL_1, reg, 0);
> > + if (ret)
> > + return ret;
> > + return regmap_update_bits(wdt->gsc->regmap, GSC_CTRL_1, reg, reg);
> > +}
> > +
> > +static int gsc_wdt_stop(struct watchdog_device *wdd)
> > +{
> > + struct gsc_wdt *wdt = watchdog_get_drvdata(wdd);
> > + unsigned int reg = (1 << GSC_CTRL_1_WDT_ENABLE);
> > +
>
> BIT(). You might as well drop the variable and just use
> BIT(GSC_CTRL_1_WDT_ENABLE) below.
>
> > + dev_dbg(wdd->parent, "%s\n", __func__);
> > +
> > + return regmap_update_bits(wdt->gsc->regmap, GSC_CTRL_1, reg, 0);
> > +}
> > +
> > +static int gsc_wdt_set_timeout(struct watchdog_device *wdd,
> > + unsigned int timeout)
> > +{
> > + struct gsc_wdt *wdt = watchdog_get_drvdata(wdd);
> > + unsigned int long_sel = 0;
> > +
> > + dev_dbg(wdd->parent, "%s: %d\n", __func__, timeout);
> > +
> > + switch (timeout) {
> > + case 60:
> > + long_sel = (1 << GSC_CTRL_1_WDT_TIME);
> > + case 30:
> > + regmap_update_bits(wdt->gsc->regmap, GSC_CTRL_1,
> > + (1 << GSC_CTRL_1_WDT_TIME),
>
> BIT()
>
> > + (long_sel << GSC_CTRL_1_WDT_TIME));

This looks wrong. Are you sure that in case of 60 timeout you want to
actually write

((1 << GSC_CTRL_1_WDT_TIME) << GSC_CTRL_1_WDT_TIME)

to the register?

Or you meant to write:

long_sel = timeout > 30;
regmap_update_bits(wdt->gsc->regmap, GSC_CTRL_1,
(long_sel << GSC_CTRL_1_WDT_TIME),

Thanks.

--
Dmitry

\
 
 \ /
  Last update: 2018-03-30 19:49    [W:0.046 / U:0.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site