lkml.org 
[lkml]   [2018]   [Mar]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v6 1/3] dt-bindings: display: bridge: Document THC63LVD1024 LVDS decoder
From
Date
Hello!

On 3/27/2018 10:33 AM, jacopo mondi wrote:
[...]
>>>>>> Document Thine THC63LVD1024 LVDS decoder device tree bindings.
>>>>>>
>>>>>> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
>>>>>> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
>>>>>> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
>>>>>> ---
>>>>>> .../bindings/display/bridge/thine,thc63lvd1024.txt | 66 +++++++++++++++++++
>>>>>> 1 file changed, 66 insertions(+)
>>>>>> create mode 100644
>>>>>> Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
>>>>>>
>>>>>> diff --git
>>>>>> a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
>>>>>> b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
>>>>>> new file mode 100644
>>>>>> index 0000000..8225c6a
>>>>>> --- /dev/null
>>>>>> +++
>>>>>> b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
>>>>>> @@ -0,0 +1,66 @@
>>>>>> +Thine Electronics THC63LVD1024 LVDS decoder
>>>>>> +-------------------------------------------
>>>>>> +
>>>>>> +The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS
>>>>>> streams
>>>>>> +to parallel data outputs. The chip supports single/dual input/output modes,
>>>>>> +handling up to two two input LVDS stream and up to two digital CMOS/TTL
>>>>>> outputs.
>>>>>> +
>>>>>> +Single or dual operation modes, output data mapping and DDR output modes
>>>>>> are
>>>>>> +configured through input signals and the chip does not expose any control
>>>>>> bus.
>>>>>> +
>>>>>> +Required properties:
>>>>>> +- compatible: Shall be "thine,thc63lvd1024"
>>>>>> +
>>>>>> +Optional properties:
>>>>>> +- vcc-supply: Power supply for TTL output and digital circuitry
>>>>>> +- cvcc-supply: Power supply for TTL CLOCKOUT signal
>>>>>> +- lvcc-supply: Power supply for LVDS inputs
>>>>>> +- pvcc-supply: Power supply for PLL circuitry
>>>>> As explained in a comment to one of the previous versions of this series, I'm
>>>>> tempted to make vcc-supply mandatory and drop the three other power supplies
>>>>> for now, as I believe there's very little chance they will be connected to
>>>>> separately controllable regulators (all supplies use the same voltage). In the
>>>>> very unlikely event that this occurs in design we need to support in the
>>>>> future, the cvcc, lvcc and pvcc supplies can be added later as optional
>>>>> without breaking backward compatibility.
>>>> I'm okay with that.
>>>>
>>>>> Apart from that,
>>>>>
>>>>> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
>>>>>
>>>>>> +- pdwn-gpios: Power down GPIO signal. Active low
>>>> powerdown-gpios is the semi-standard name.
>>>>
>>> right, I've also noticed it. If possible please avoid shortenings in
>>> property names.
>>
>> It is not shortening, it just follow pin name from decoder's datasheet.
>>
>>>
>>>>>> +- oe-gpios: Output enable GPIO signal. Active high
>>>>>> +
>>> And this one is also a not ever met property name, please consider to
>>> rename it to 'enable-gpios', for instance display panels define it.
>>
>>
>> Again, it follows datasheet naming scheme. Has something changed in DT
>> conventions?
>
> Seconded. My understanding is that the property name should reflect
> what reported in the the chip manual. For THC63LVD1024 the enable and
> power down pins are named 'OE' and 'PDWN' respectively.

But don't we need the vendor prefix in the prop names then, like
"renesas,oe-gpios" then?

> Thanks
> j

MBR, Sergei

\
 
 \ /
  Last update: 2018-03-27 10:28    [W:0.066 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site