lkml.org 
[lkml]   [2018]   [Mar]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH net-next 6/8] MIPS: mscc: Add switch to ocelot
From
Date
On 03/23/2018 01:11 PM, Alexandre Belloni wrote:
> Ocelot has an integrated switch, add support for it.
>
> Cc: James Hogan <jhogan@kernel.org>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
> ---
> arch/mips/boot/dts/mscc/ocelot.dtsi | 84 +++++++++++++++++++++++++++++++++++++
> 1 file changed, 84 insertions(+)
>
> diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
> index dd239cab2f9d..22a86373b1c9 100644
> --- a/arch/mips/boot/dts/mscc/ocelot.dtsi
> +++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
> @@ -91,6 +91,69 @@
> status = "disabled";
> };
>
> + switch@1010000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "mscc,ocelot-switch";
> + reg = <0x1010000 0x10000>,
> + <0x1030000 0x10000>,
> + <0x1080000 0x100>,
> + <0x10d0000 0x10000>,
> + <0x11e0000 0x100>,
> + <0x11f0000 0x100>,
> + <0x1200000 0x100>,
> + <0x1210000 0x100>,
> + <0x1220000 0x100>,
> + <0x1230000 0x100>,
> + <0x1240000 0x100>,
> + <0x1250000 0x100>,
> + <0x1260000 0x100>,
> + <0x1270000 0x100>,
> + <0x1280000 0x100>,
> + <0x1800000 0x80000>,
> + <0x1880000 0x10000>;
> + reg-names = "sys", "rew", "qs", "hsio", "port0",
> + "port1", "port2", "port3", "port4", "port5",
> + "port6", "port7", "port8", "port9", "port10",
> + "qsys", "ana";
> + interrupts = <21 22>;
> + interrupt-names = "xtr", "inj";

See my comment about the binding patch, this should be moved to a ports
subnode so it is conforming to the existing DSA binding and makes it a
lot easier to have all ports disabled by default at the .dsti level by
not defini

> +
> + port0: port@0 {
> + reg = <0>;
> + };
> + port1: port@1 {
> + reg = <1>;
> + };
> + port2: port@2 {
> + reg = <2>;
> + };
> + port3: port@3 {
> + reg = <3>;
> + };
> + port4: port@4 {
> + reg = <4>;
> + };
> + port5: port@5 {
> + reg = <5>;
> + };
> + port6: port@6 {
> + reg = <6>;
> + };
> + port7: port@7 {
> + reg = <7>;
> + };
> + port8: port@8 {
> + reg = <8>;
> + };
> + port9: port@9 {
> + reg = <9>;
> + };
> + port10: port@10 {
> + reg = <10>;
> + };
> + };
> +
> reset@1070008 {
> compatible = "mscc,ocelot-chip-reset";
> reg = <0x1070008 0x4>;
> @@ -113,5 +176,26 @@
> function = "uart2";
> };
> };
> +
> + mdio0: mdio@107009c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "mscc,ocelot-miim";
> + reg = <0x107009c 0x36>, <0x10700f0 0x8>;
> + interrupts = <14>;

status = "disabled" by default?

> +
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + };
> + phy1: ethernet-phy@1 {
> + reg = <1>;
> + };
> + phy2: ethernet-phy@2 {
> + reg = <2>;
> + };
> + phy3: ethernet-phy@3 {
> + reg = <3>;
> + };

These PHYs should be defined at the board DTS level.
--
Florian

\
 
 \ /
  Last update: 2018-03-23 22:18    [W:0.479 / U:0.580 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site