lkml.org 
[lkml]   [2018]   [Mar]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2 1/6] phy: qcom-qmp: Enable pipe_clk before checking USB3 PHY_STATUS
Date
Quoting Manu Gautam (2018-03-22 01:50:41)
> QMP PHY for USB mode requires pipe_clk for calibration and PLL lock
> to take place. This lock is output from PHY to GCC clock_ctl and then

s/lock/clock/

> fed back to QMP PHY and is output from PHY only after PHY is reset
> and initialized, hence it can't be enabled too early in initialization
> sequence.
>
> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
> ---
> drivers/phy/qualcomm/phy-qcom-qmp.c | 18 ++++++++++++++++++
> 1 file changed, 18 insertions(+)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index 6470c5d..73aa282 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -797,8 +797,13 @@ static int qcom_qmp_phy_poweron(struct phy *phy)
> {
> struct qmp_phy *qphy = phy_get_drvdata(phy);
> struct qcom_qmp *qmp = qphy->qmp;
> + const struct qmp_phy_cfg *cfg = qmp->cfg;
> int ret;
>
> + /* Not needed for USB3 PHY as pipe_clk is enabled from phy_init */
> + if (cfg->type == PHY_TYPE_USB3)
> + return 0;

Would be nice to not even assign phy_poweron when the PHY is USB3 type.

> +
> ret = clk_prepare_enable(qphy->pipe_clk);
> if (ret)
> dev_err(qmp->dev, "pipe_clk enable failed, err=%d\n", ret);
> @@ -1008,6 +1013,19 @@ static int qcom_qmp_phy_init(struct phy *phy)
> status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
> mask = cfg->mask_pcs_ready;
>
> + /* USB3 PHY requires pipe_clk for PLL lock and calibration */
> + if (cfg->type == PHY_TYPE_USB3) {
> + ret = clk_prepare_enable(qphy->pipe_clk);
> + if (ret)
> + dev_err(qmp->dev, "pipe_clk enable err=%d\n", ret);
> + /*
> + * Ignore this error as pipe_clk might take some time to get
> + * enabled. In any case following check for PHY PLL lock would
> + * timeout below if there is a fatal error and clock is not fed
> + * to PHY
> + */
> +

This is odd. If clk_enable() fails then we don't keep parent clks (or
the clk that's being operated on) up refcounted and enabled. How is that
going to work?

\
 
 \ /
  Last update: 2018-03-22 19:44    [W:0.176 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site