lkml.org 
[lkml]   [2018]   [Mar]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RESEND PATCH v5 0/6] IR support for A83T
From
Date


On 13.02.2018 13:29, Philipp Rossak wrote:
> This patch series adds support for the sunxi A83T ir module and enhances
> the sunxi-ir driver. Right now the base clock frequency for the ir driver
> is a hard coded define and is set to 8 MHz.
> This works for the most common ir receivers. On the Sinovoip Bananapi M3
> the ir receiver needs, a 3 MHz base clock frequency to work without
> problems with this driver.
>
> This patch series adds support for an optinal property that makes it able
> to override the default base clock frequency and enables the ir interface
> on the a83t and the Bananapi M3.
>
> changes since v4:
> * rename cir pin from cir_pins to r_cir_pin
> * drop unit-adress from r_cir_pin
> * add a83t compatible to the cir node
> * move muxing options to dtsi
> * rename cir label and reorder it in the bananpim3.dts file
>
> changes since v3:
> * collecting all acks & reviewd by
> * fixed typos
>
> changes since v2:
> * reorder cir pin (alphabetical)
> * fix typo in documentation
>
> changes since v1:
> * fix typos, reword Documentation
> * initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
> * change dev_info() to dev_dbg()
> * change naming to cir* in dts/dtsi
> * Added acked Ackedi-by to related patch
> * use whole memory block instead of registers needed + fix for h3/h5
>
> changes since rfc:
> * The property is now optinal. If the property is not available in
> the dtb the driver uses the default base clock frequency.
> * the driver prints out the the selected base clock frequency.
> * changed devicetree property from base-clk-frequency to clock-frequency
>
> Regards,
> Philipp
>
> Philipp Rossak (6):
> media: rc: update sunxi-ir driver to get base clock frequency from
> devicetree
> media: dt: bindings: Update binding documentation for sunxi IR
> controller
> arm: dts: sun8i: a83t: Add the cir pin for the A83T
> arm: dts: sun8i: a83t: Add support for the cir interface
> arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
> arm: dts: sun8i: h3-h5: ir register size should be the whole memory
> block
>
> Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++
> arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 5 +++++
> arch/arm/boot/dts/sun8i-a83t.dtsi | 18 ++++++++++++++++++
> arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +-
> drivers/media/rc/sunxi-cir.c | 19 +++++++++++--------
> 5 files changed, 38 insertions(+), 9 deletions(-)
>

I talked yesterday with Maxime about this patch series. And he told me
if the first to patches got merged, he will apply the dts patches to the
sunxi tree.

Sean, can you merge the first two patches through the rc-core?

Thanks,
Philipp

\
 
 \ /
  Last update: 2018-03-02 13:12    [W:0.087 / U:0.304 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site