lkml.org 
[lkml]   [2018]   [Mar]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] clk: tegra: fix pllu rate configuration
From
Date

On 22/02/18 23:04, Marcel Ziswiler wrote:
> Turns out latest upstream U-Boot does not configure/enable pllu which
> leaves it at some default rate of 500 kHz:
>
> root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep pll_u
> pll_u 3 3 0 500000 0
>
> Of course this won't quite work leading to the following messages:
>
> [ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
> ehci
> [ 11.759173] usb 2-1: device descriptor read/64, error -110
> [ 27.119453] usb 2-1: device descriptor read/64, error -110
> [ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
> ehci
> [ 32.559454] usb 2-1: device descriptor read/64, error -110
> [ 47.929777] usb 2-1: device descriptor read/64, error -110
> [ 48.049658] usb usb2-port1: attempt power cycle
> [ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
> ehci
> [ 59.349457] usb 2-1: device not accepting address 4, error -110
> [ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
> ehci
> [ 70.069457] usb 2-1: device not accepting address 5, error -110
> [ 70.079721] usb usb2-port1: unable to enumerate USB device
>
> Fix this by actually allowing the rate also being set from within
> the Linux kernel.
>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>
> ---
>
> drivers/clk/tegra/clk-pll.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/drivers/clk/tegra/clk-pll.c b/drivers/clk/tegra/clk-pll.c
> index 7c369e21c91c..830d1c87fa7c 100644
> --- a/drivers/clk/tegra/clk-pll.c
> +++ b/drivers/clk/tegra/clk-pll.c
> @@ -1151,6 +1151,8 @@ static const struct clk_ops tegra_clk_pllu_ops = {
> .enable = clk_pllu_enable,
> .disable = clk_pll_disable,
> .recalc_rate = clk_pll_recalc_rate,
> + .round_rate = clk_pll_round_rate,
> + .set_rate = clk_pll_set_rate,
> };
>
> static int _pll_fixed_mdiv(struct tegra_clk_pll_params *pll_params,

Thanks for the fix. I have tested this on Tegra30 cardhu and this
resolves a problem booting this board with the upstream uboot bootloader.

We just need to align with Peter on the best way to fix.

Cheers,
Jon

--
nvpublic

\
 
 \ /
  Last update: 2018-03-02 11:50    [W:0.074 / U:0.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site