lkml.org 
[lkml]   [2018]   [Mar]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2] usb: dwc3: Prevent indefinite sleep in _dwc3_set_mode during suspend/resume
Date
Hi,

On 3/19/2018 3:36 PM, Minas Harutyunyan wrote:
> Hi,
>
> On 3/19/2018 12:55 PM, Felipe Balbi wrote:
>>
>> Hi,
>>
>> Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> writes:
>>>>>>>> Thanks for picking this for -next.
>>>>>>>> Is it better to have this in v4.16-rc fixes?
>>>>>>>> and also stable? v4.12+
>>>>>>>
>>>>>>> Well, there was no "Fixes: foobar" or "Cc: stable" lines in the commit
>>>>>>> log ;-)
>>>>>>>
>>>>>>> The best we can do now, is wait for -rc1 and manually send the commit to
>>>>>>> stable.
>>>>>>>
>>>>>>
>>>>>> That's fine. Thanks.
>>>>>>
>>>>>
>>>>> Same issue seen in dwc3_gadget_ep_dequeue() function where also used
>>>>> wait_event_lock_irq() - as result infinite loop.
>>>>
>>>> how did this happen? During rmmod dwc3? Or, perhaps, after you unloaded
>>>> a gadget driver?
>>>>
>>> No, not during rmmod's.
>>> We using our internal USB testing tool. Test case; ISOC OUT, transfer
>>> size N frames. When host starts ISOC OUT traffic then the dwc3 based on
>>> "Transfer not ready" event in frame F starts transfers staring from
>>> frame F+4 (for bInterval=1) as result 4 requests, which already queued
>>> on device side, remain incomplete. Function driver on some timeout
>>> trying dequeue these 4 requests (without disabling EP) to complete test.
>>> For IN ISOC's these requests completed on MISSED ISOC event, but for
>>> ISOC OUT required call dequeue on some timeout.
>>
>> okay
>>
>>>>> Actually to fix this issue I updated condition of wait function
>>>>> from:
>>>>> !(dep->flags & DWC3_EP_END_TRANSFER_PENDING)
>>>>> to:
>>>>> !(dep->flags & DWC3_EP_END_TRANSFER_PENDING & DWC3_EP_ENABLED)
>>>>
>>>> you're not fixing anything. You're, essentially, removing the entire
>>>> end transfer pending logic.
>>> yes, you are right, but how to overcome this infinite loop? Replace
>>> wait_event_lock_irq() by wait_event_interruptible_lock_irq_timeout()?
>>
>> The best way here would be to figure why we're missing command complete
>> IRQ in those cases. According to documentation, we *should* receive that
>> interrupt, so why is it missing?
>>
>
> Additional info on test. Core configuration is HS only mode, test speed
> HS, core version v2.90a. Maybe it will help to understand cause of issue.
> BTW, currently to pass above describe ISOC OUT test we just commented
> wait_event_lock_irq() in dwc3_gadget_ep_dequeue() function and
> successfully received request completion in function driver.
> Thanks,
> Minas
>

One more info: while function driver call dequeue, host periodically
send control read command to get status of test from function - test In
Progress or Finished.
Thanks,
Minas

\
 
 \ /
  Last update: 2018-03-19 14:54    [W:0.947 / U:0.004 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site