lkml.org 
[lkml]   [2018]   [Mar]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v7 1/2] hwmon: (ucd9000) Add gpio chip interface
Date
From: Christopher Bostic <cbostic@linux.vnet.ibm.com>

Add a struct gpio_chip and define some methods so that this device's
I/O can be accessed via /sys/class/gpio.

Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
---
drivers/hwmon/pmbus/ucd9000.c | 212 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 212 insertions(+)

diff --git a/drivers/hwmon/pmbus/ucd9000.c b/drivers/hwmon/pmbus/ucd9000.c
index b74dbec..ef2c5bf 100644
--- a/drivers/hwmon/pmbus/ucd9000.c
+++ b/drivers/hwmon/pmbus/ucd9000.c
@@ -27,6 +27,8 @@
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/pmbus.h>
+#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
#include "pmbus.h"

enum chips { ucd9000, ucd90120, ucd90124, ucd90160, ucd9090, ucd90910 };
@@ -35,8 +37,18 @@
#define UCD9000_NUM_PAGES 0xd6
#define UCD9000_FAN_CONFIG_INDEX 0xe7
#define UCD9000_FAN_CONFIG 0xe8
+#define UCD9000_GPIO_SELECT 0xfa
+#define UCD9000_GPIO_CONFIG 0xfb
#define UCD9000_DEVICE_ID 0xfd

+/* GPIO CONFIG bits */
+#define UCD9000_GPIO_CONFIG_ENABLE BIT(0)
+#define UCD9000_GPIO_CONFIG_OUT_ENABLE BIT(1)
+#define UCD9000_GPIO_CONFIG_OUT_VALUE BIT(2)
+#define UCD9000_GPIO_CONFIG_STATUS BIT(3)
+#define UCD9000_GPIO_INPUT 0
+#define UCD9000_GPIO_OUTPUT 1
+
#define UCD9000_MON_TYPE(x) (((x) >> 5) & 0x07)
#define UCD9000_MON_PAGE(x) ((x) & 0x0f)

@@ -47,9 +59,17 @@

#define UCD9000_NUM_FAN 4

+#define UCD9000_GPIO_NAME_LEN 16
+#define UCD9090_NUM_GPIOS 23
+#define UCD901XX_NUM_GPIOS 26
+#define UCD90910_NUM_GPIOS 26
+
struct ucd9000_data {
u8 fan_data[UCD9000_NUM_FAN][I2C_SMBUS_BLOCK_MAX];
struct pmbus_driver_info info;
+#ifdef CONFIG_GPIOLIB
+ struct gpio_chip gpio;
+#endif
};
#define to_ucd9000_data(_info) container_of(_info, struct ucd9000_data, info)

@@ -149,6 +169,196 @@ static int ucd9000_read_byte_data(struct i2c_client *client, int page, int reg)
};
MODULE_DEVICE_TABLE(of, ucd9000_of_match);

+#ifdef CONFIG_GPIOLIB
+static int ucd9000_gpio_read_config(struct i2c_client *client,
+ unsigned int offset)
+{
+ int ret;
+
+ /* No page set required */
+ ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_SELECT, offset);
+ if (ret < 0)
+ return ret;
+
+ return i2c_smbus_read_byte_data(client, UCD9000_GPIO_CONFIG);
+}
+
+static int ucd9000_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+ struct i2c_client *client = gpiochip_get_data(gc);
+ int ret;
+
+ ret = ucd9000_gpio_read_config(client, offset);
+ if (ret < 0)
+ return ret;
+
+ return !!(ret & UCD9000_GPIO_CONFIG_STATUS);
+}
+
+static void ucd9000_gpio_set(struct gpio_chip *gc, unsigned int offset,
+ int value)
+{
+ struct i2c_client *client = gpiochip_get_data(gc);
+ int ret;
+
+ ret = ucd9000_gpio_read_config(client, offset);
+ if (ret < 0) {
+ dev_dbg(&client->dev, "failed to read GPIO %d config: %d\n",
+ offset, ret);
+ return;
+ }
+
+ if (value) {
+ if (ret & UCD9000_GPIO_CONFIG_STATUS)
+ return;
+
+ ret |= UCD9000_GPIO_CONFIG_STATUS;
+ } else {
+ if (!(ret & UCD9000_GPIO_CONFIG_STATUS))
+ return;
+
+ ret &= ~UCD9000_GPIO_CONFIG_STATUS;
+ }
+
+ ret |= UCD9000_GPIO_CONFIG_ENABLE;
+
+ /* Page set not required */
+ ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
+ if (ret < 0) {
+ dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
+ offset, ret);
+ return;
+ }
+
+ ret &= ~UCD9000_GPIO_CONFIG_ENABLE;
+
+ ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
+ if (ret < 0)
+ dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
+ offset, ret);
+}
+
+static int ucd9000_gpio_get_direction(struct gpio_chip *gc,
+ unsigned int offset)
+{
+ struct i2c_client *client = gpiochip_get_data(gc);
+ int ret;
+
+ ret = ucd9000_gpio_read_config(client, offset);
+ if (ret < 0)
+ return ret;
+
+ return !(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE);
+}
+
+static int ucd9000_gpio_set_direction(struct gpio_chip *gc,
+ unsigned int offset, bool direction_out,
+ int requested_out)
+{
+ struct i2c_client *client = gpiochip_get_data(gc);
+ int ret, config, out_val;
+
+ ret = ucd9000_gpio_read_config(client, offset);
+ if (ret < 0)
+ return ret;
+
+ if (direction_out) {
+ out_val = requested_out ? UCD9000_GPIO_CONFIG_OUT_VALUE : 0;
+
+ if (ret & UCD9000_GPIO_CONFIG_OUT_ENABLE) {
+ if ((ret & UCD9000_GPIO_CONFIG_OUT_VALUE) == out_val)
+ return 0;
+ } else {
+ ret |= UCD9000_GPIO_CONFIG_OUT_ENABLE;
+ }
+
+ if (out_val)
+ ret |= UCD9000_GPIO_CONFIG_OUT_VALUE;
+ else
+ ret &= ~UCD9000_GPIO_CONFIG_OUT_VALUE;
+
+ } else {
+ if (!(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE))
+ return 0;
+
+ ret &= ~UCD9000_GPIO_CONFIG_OUT_ENABLE;
+ }
+
+ ret |= UCD9000_GPIO_CONFIG_ENABLE;
+ config = ret;
+
+ /* Page set not required */
+ ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config);
+ if (ret < 0)
+ return ret;
+
+ config &= ~UCD9000_GPIO_CONFIG_ENABLE;
+
+ return i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config);
+}
+
+static int ucd9000_gpio_direction_input(struct gpio_chip *gc,
+ unsigned int offset)
+{
+ return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_INPUT, 0);
+}
+
+static int ucd9000_gpio_direction_output(struct gpio_chip *gc,
+ unsigned int offset, int val)
+{
+ return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_OUTPUT,
+ val);
+}
+
+static void ucd9000_probe_gpio(struct i2c_client *client,
+ const struct i2c_device_id *mid,
+ struct ucd9000_data *data)
+{
+ int rc;
+
+ switch (mid->driver_data) {
+ case ucd9090:
+ data->gpio.ngpio = UCD9090_NUM_GPIOS;
+ break;
+ case ucd90120:
+ case ucd90124:
+ case ucd90160:
+ data->gpio.ngpio = UCD901XX_NUM_GPIOS;
+ break;
+ case ucd90910:
+ data->gpio.ngpio = UCD90910_NUM_GPIOS;
+ break;
+ default:
+ return; /* GPIO support is optional. */
+ }
+
+ /*
+ * Pinmux support has not been added to the new gpio_chip.
+ * This support should be added when possible given the mux
+ * behavior of these IO devices.
+ */
+ data->gpio.label = client->name;
+ data->gpio.get_direction = ucd9000_gpio_get_direction;
+ data->gpio.direction_input = ucd9000_gpio_direction_input;
+ data->gpio.direction_output = ucd9000_gpio_direction_output;
+ data->gpio.get = ucd9000_gpio_get;
+ data->gpio.set = ucd9000_gpio_set;
+ data->gpio.can_sleep = true;
+ data->gpio.base = -1;
+ data->gpio.parent = &client->dev;
+
+ rc = devm_gpiochip_add_data(&client->dev, &data->gpio, client);
+ if (rc)
+ dev_warn(&client->dev, "Could not add gpiochip: %d\n", rc);
+}
+#else
+static void ucd9000_probe_gpio(struct i2c_client *client,
+ const struct i2c_device_id *mid,
+ struct ucd9000_data *data)
+{
+}
+#endif /* CONFIG_GPIOLIB */
+
static int ucd9000_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
@@ -263,6 +473,8 @@ static int ucd9000_probe(struct i2c_client *client,
| PMBUS_HAVE_FAN34 | PMBUS_HAVE_STATUS_FAN34;
}

+ ucd9000_probe_gpio(client, mid, data);
+
return pmbus_do_probe(client, mid, info);
}

--
1.8.3.1
\
 
 \ /
  Last update: 2018-03-16 22:22    [W:0.039 / U:1.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site