lkml.org 
[lkml]   [2018]   [Mar]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 1/2] hwmon: (ucd9000) Add gpio chip interface
From
Date


On 03/16/2018 08:40 AM, Guenter Roeck wrote:
> On 03/15/2018 03:21 PM, Eddie James wrote:
>> From: Christopher Bostic <cbostic@linux.vnet.ibm.com>
>>
>> Add a struct gpio_chip and define some methods so that this device's
>> I/O can be accessed via /sys/class/gpio.
>>
>
> Sorry for not noticing earlier. The 0day reports should be addressed
> by selecting GPIOLIB
> in the Kconfig entry.

Getting kbuild recursive dependencies when I select GPIOLIB for ucd9000 :(

May have to do "depends on" instead and #ifdef GPIOLIB in ucd9000,
unless you have another recommendation?

Thanks
Eddie

>
> Guenter
>
>> Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
>> Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
>> Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
>> ---
>>   drivers/hwmon/pmbus/ucd9000.c | 201
>> ++++++++++++++++++++++++++++++++++++++++++
>>   1 file changed, 201 insertions(+)
>>
>> diff --git a/drivers/hwmon/pmbus/ucd9000.c
>> b/drivers/hwmon/pmbus/ucd9000.c
>> index b74dbec..a34ffc4 100644
>> --- a/drivers/hwmon/pmbus/ucd9000.c
>> +++ b/drivers/hwmon/pmbus/ucd9000.c
>> @@ -27,6 +27,7 @@
>>   #include <linux/slab.h>
>>   #include <linux/i2c.h>
>>   #include <linux/pmbus.h>
>> +#include <linux/gpio.h>
>>   #include "pmbus.h"
>>     enum chips { ucd9000, ucd90120, ucd90124, ucd90160, ucd9090,
>> ucd90910 };
>> @@ -35,8 +36,18 @@
>>   #define UCD9000_NUM_PAGES        0xd6
>>   #define UCD9000_FAN_CONFIG_INDEX    0xe7
>>   #define UCD9000_FAN_CONFIG        0xe8
>> +#define UCD9000_GPIO_SELECT        0xfa
>> +#define UCD9000_GPIO_CONFIG        0xfb
>>   #define UCD9000_DEVICE_ID        0xfd
>>   +/* GPIO CONFIG bits */
>> +#define UCD9000_GPIO_CONFIG_ENABLE    BIT(0)
>> +#define UCD9000_GPIO_CONFIG_OUT_ENABLE    BIT(1)
>> +#define UCD9000_GPIO_CONFIG_OUT_VALUE    BIT(2)
>> +#define UCD9000_GPIO_CONFIG_STATUS    BIT(3)
>> +#define UCD9000_GPIO_INPUT        0
>> +#define UCD9000_GPIO_OUTPUT        1
>> +
>>   #define UCD9000_MON_TYPE(x)    (((x) >> 5) & 0x07)
>>   #define UCD9000_MON_PAGE(x)    ((x) & 0x0f)
>>   @@ -47,9 +58,15 @@
>>     #define UCD9000_NUM_FAN        4
>>   +#define UCD9000_GPIO_NAME_LEN    16
>> +#define UCD9090_NUM_GPIOS    23
>> +#define UCD901XX_NUM_GPIOS    26
>> +#define UCD90910_NUM_GPIOS    26
>> +
>>   struct ucd9000_data {
>>       u8 fan_data[UCD9000_NUM_FAN][I2C_SMBUS_BLOCK_MAX];
>>       struct pmbus_driver_info info;
>> +    struct gpio_chip gpio;
>>   };
>>   #define to_ucd9000_data(_info) container_of(_info, struct
>> ucd9000_data, info)
>>   @@ -149,6 +166,188 @@ static int ucd9000_read_byte_data(struct
>> i2c_client *client, int page, int reg)
>>   };
>>   MODULE_DEVICE_TABLE(of, ucd9000_of_match);
>>   +static int ucd9000_gpio_read_config(struct i2c_client *client,
>> +                    unsigned int offset)
>> +{
>> +    int ret;
>> +
>> +    /* No page set required */
>> +    ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_SELECT,
>> offset);
>> +    if (ret < 0)
>> +        return ret;
>> +
>> +    return i2c_smbus_read_byte_data(client, UCD9000_GPIO_CONFIG);
>> +}
>> +
>> +static int ucd9000_gpio_get(struct gpio_chip *gc, unsigned int offset)
>> +{
>> +    struct i2c_client *client  = gpiochip_get_data(gc);
>> +    int ret;
>> +
>> +    ret = ucd9000_gpio_read_config(client, offset);
>> +    if (ret < 0)
>> +        return ret;
>> +
>> +    return !!(ret & UCD9000_GPIO_CONFIG_STATUS);
>> +}
>> +
>> +static void ucd9000_gpio_set(struct gpio_chip *gc, unsigned int offset,
>> +                 int value)
>> +{
>> +    struct i2c_client *client = gpiochip_get_data(gc);
>> +    int ret;
>> +
>> +    ret = ucd9000_gpio_read_config(client, offset);
>> +    if (ret < 0) {
>> +        dev_dbg(&client->dev, "failed to read GPIO %d config: %d\n",
>> +            offset, ret);
>> +        return;
>> +    }
>> +
>> +    if (value) {
>> +        if (ret & UCD9000_GPIO_CONFIG_STATUS)
>> +            return;
>> +
>> +        ret |= UCD9000_GPIO_CONFIG_STATUS;
>> +    } else {
>> +        if (!(ret & UCD9000_GPIO_CONFIG_STATUS))
>> +            return;
>> +
>> +        ret &= ~UCD9000_GPIO_CONFIG_STATUS;
>> +    }
>> +
>> +    ret |= UCD9000_GPIO_CONFIG_ENABLE;
>> +
>> +    /* Page set not required */
>> +    ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
>> +    if (ret < 0) {
>> +        dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
>> +            offset, ret);
>> +        return;
>> +    }
>> +
>> +    ret &= ~UCD9000_GPIO_CONFIG_ENABLE;
>> +
>> +    ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
>> +    if (ret < 0)
>> +        dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
>> +            offset, ret);
>> +}
>> +
>> +static int ucd9000_gpio_get_direction(struct gpio_chip *gc,
>> +                      unsigned int offset)
>> +{
>> +    struct i2c_client *client = gpiochip_get_data(gc);
>> +    int ret;
>> +
>> +    ret = ucd9000_gpio_read_config(client, offset);
>> +    if (ret < 0)
>> +        return ret;
>> +
>> +    return !(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE);
>> +}
>> +
>> +static int ucd9000_gpio_set_direction(struct gpio_chip *gc,
>> +                      unsigned int offset, bool direction_out,
>> +                      int requested_out)
>> +{
>> +    struct i2c_client *client = gpiochip_get_data(gc);
>> +    int ret, config, out_val;
>> +
>> +    ret = ucd9000_gpio_read_config(client, offset);
>> +    if (ret < 0)
>> +        return ret;
>> +
>> +    if (direction_out) {
>> +        out_val = requested_out ? UCD9000_GPIO_CONFIG_OUT_VALUE : 0;
>> +
>> +        if (ret & UCD9000_GPIO_CONFIG_OUT_ENABLE) {
>> +            if ((ret & UCD9000_GPIO_CONFIG_OUT_VALUE) == out_val)
>> +                return 0;
>> +        } else {
>> +            ret |= UCD9000_GPIO_CONFIG_OUT_ENABLE;
>> +        }
>> +
>> +        if (out_val)
>> +            ret |= UCD9000_GPIO_CONFIG_OUT_VALUE;
>> +        else
>> +            ret &= ~UCD9000_GPIO_CONFIG_OUT_VALUE;
>> +
>> +    } else {
>> +        if (!(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE))
>> +            return 0;
>> +
>> +        ret &= ~UCD9000_GPIO_CONFIG_OUT_ENABLE;
>> +    }
>> +
>> +    ret |= UCD9000_GPIO_CONFIG_ENABLE;
>> +    config = ret;
>> +
>> +    /* Page set not required */
>> +    ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG,
>> config);
>> +    if (ret < 0)
>> +        return ret;
>> +
>> +    config &= ~UCD9000_GPIO_CONFIG_ENABLE;
>> +
>> +    return i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG,
>> config);
>> +}
>> +
>> +static int ucd9000_gpio_direction_input(struct gpio_chip *gc,
>> +                    unsigned int offset)
>> +{
>> +    return ucd9000_gpio_set_direction(gc, offset,
>> UCD9000_GPIO_INPUT, 0);
>> +}
>> +
>> +static int ucd9000_gpio_direction_output(struct gpio_chip *gc,
>> +                     unsigned int offset, int val)
>> +{
>> +    return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_OUTPUT,
>> +                      val);
>> +}
>> +
>> +static void ucd9000_probe_gpio(struct i2c_client *client,
>> +                   const struct i2c_device_id *mid,
>> +                   struct ucd9000_data *data)
>> +{
>> +    int rc;
>> +
>> +    switch (mid->driver_data) {
>> +    case ucd9090:
>> +        data->gpio.ngpio = UCD9090_NUM_GPIOS;
>> +        break;
>> +    case ucd90120:
>> +    case ucd90124:
>> +    case ucd90160:
>> +        data->gpio.ngpio = UCD901XX_NUM_GPIOS;
>> +        break;
>> +    case ucd90910:
>> +        data->gpio.ngpio = UCD90910_NUM_GPIOS;
>> +        break;
>> +    default:
>> +        return; /* GPIO support is optional. */
>> +    }
>> +
>> +    /*
>> +     * Pinmux support has not been added to the new gpio_chip.
>> +     * This support should be added when possible given the mux
>> +     * behavior of these IO devices.
>> +     */
>> +    data->gpio.label = client->name;
>> +    data->gpio.get_direction = ucd9000_gpio_get_direction;
>> +    data->gpio.direction_input = ucd9000_gpio_direction_input;
>> +    data->gpio.direction_output = ucd9000_gpio_direction_output;
>> +    data->gpio.get = ucd9000_gpio_get;
>> +    data->gpio.set = ucd9000_gpio_set;
>> +    data->gpio.can_sleep = true;
>> +    data->gpio.base = -1;
>> +    data->gpio.parent = &client->dev;
>> +
>> +    rc = devm_gpiochip_add_data(&client->dev, &data->gpio, client);
>> +    if (rc)
>> +        dev_warn(&client->dev, "Could not add gpiochip: %d\n", rc);
>> +}
>> +
>>   static int ucd9000_probe(struct i2c_client *client,
>>                const struct i2c_device_id *id)
>>   {
>> @@ -263,6 +462,8 @@ static int ucd9000_probe(struct i2c_client *client,
>>             | PMBUS_HAVE_FAN34 | PMBUS_HAVE_STATUS_FAN34;
>>       }
>>   +    ucd9000_probe_gpio(client, mid, data);
>> +
>>       return pmbus_do_probe(client, mid, info);
>>   }
>>
>

\
 
 \ /
  Last update: 2018-03-16 19:41    [W:0.061 / U:0.068 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site