lkml.org 
[lkml]   [2018]   [Mar]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[LINUX PATCH v8 1/2] Documentation: nand: pl353: Add documentation for controller and driver
Date
From: Naga Sureshkumar Relli <nagasure@xilinx.com>

Added notes about the controller and driver

Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
---
Changes in v8
- None
Changes in v7:
- None
Changes in v6:
- None
Changes in v5:
- Fixed the review comments
Changes in v4:
- None
---
Documentation/mtd/nand/pl353-nand.txt | 92 +++++++++++++++++++++++++++++++++++
1 file changed, 92 insertions(+)
create mode 100644 Documentation/mtd/nand/pl353-nand.txt

diff --git a/Documentation/mtd/nand/pl353-nand.txt b/Documentation/mtd/nand/pl353-nand.txt
new file mode 100644
index 0000000..ac6fbd5
--- /dev/null
+++ b/Documentation/mtd/nand/pl353-nand.txt
@@ -0,0 +1,92 @@
+This documents provides some notes about the ARM pl353 smc controller used in
+Zynq SOC and confined to NAND specific details.
+
+Overview of the controller
+==========================
+ The SMC (PL353) supports two memory interfaces:
+ Interface 0 type SRAM.
+ Interface 1 type NAND.
+ This configuration supports the following configurable options:
+ . 32-bit or 64-bit AXI data width
+ . 8-bit, 16-bit, or 32-bit memory data width for interface 0
+ . 8-bit, or 16-bit memory data width for interface 1
+ . 1-4 chip selects on each interface
+ . SLC ECC block for interface 1
+
+For more information, refer the below link for TRM
+http://infocenter.arm.com/help/topic/com.arm.doc.ddi0380g/
+DDI0380G_smc_pl350_series_r2p1_trm.pdf
+
+NAND memory accesses
+====================
+ . Two phase NAND accesses
+ . NAND command phase transfers
+ . NAND data phase transfers
+
+Two phase NAND accesses
+ The SMC defines two phases of commands when transferring data to or from
+NAND flash.
+
+Command phase
+ Commands and optional address information are written to the NAND flash.
+The command and address can be associated with either a data phase operation to
+write to or read from the array, or a status/ID register transfer.
+
+Data phase
+ Data is either written to or read from the NAND flash. This data can be either
+data transferred to or from the array, or status/ID register information.
+
+NAND AXI address setup
+ AXI address Command phase Data phase
+ [31:24] Chip address Chip address
+ [23] NoOfAddCycles_2 Reserved
+ [22] NoOfAddCycles_1 Reserved
+ [21] NoOfAddCycles_0 ClearCS
+ [20] End command valid End command valid
+ [19] 0 1
+ [18:11] End command End command
+ [10:3] Start command [10] ECC Last
+ [9:3] Reserved
+ [2:0] Reserved Reserved
+
+ECC
+===
+ It operates on a number of 512 byte blocks of NAND memory and can be
+programmed to store the ECC codes after the data in memory. For writes,
+the ECC is written to the spare area of the page. For reads, the result of
+a block ECC check are made available to the device driver.
+
+------------------------------------------------------------------------
+| n * 512 blocks | extra | ecc | |
+| | block | codes | |
+------------------------------------------------------------------------
+
+The ECC calculation uses a simple Hamming code, using 1-bit correction 2-bit
+detection. It starts when a valid read or write command with a 512 byte aligned
+address is detected on the memory interface.
+
+Driver details
+==============
+ The NAND driver has dependency with the pl353_smc memory controller
+driver for intializing the nand timing parameters, bus width, ECC modes,
+control and status information.
+
+Since the controller expects that the chipselect bit should be cleared for the
+last data transfer i.e last 4 data bytes, the existing nandbase page
+read/write routines for soft ecc and ecc none modes will not work. So, inorder
+to make this driver work, it always updates the ecc mode as HW ECC and
+implemented the page read/write functions for supporting the SW ECC.
+
+HW ECC mode:
+ Upto 2K page size is supported and beyond that it retuns
+-ENOSUPPORT error. If the flsh has ONDIE ecc controller then the
+priority has given to the ONDIE ecc controller. Also the current
+implementation has support for upto 64 byte oob area
+
+SW ECC mode:
+ It supports all the pgae sizes. But since, zynq soc bootrom uses
+HW ECC for the devices that have pgae size <=2K so, to avoid any ecc related
+issues during boot, prefer HW ECC over SW ECC.
+
+For devicetree binding information please refer the below dt binding file
+Documentation/devicetree/bindings/memory-controllers/pl353-smc.txt.
--
2.7.4
\
 
 \ /
  Last update: 2018-03-14 11:50    [W:0.070 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site