lkml.org 
[lkml]   [2018]   [Mar]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] [media] ov5645: Move an error code assignment in ov5645_probe()
On Wed, Mar 14, 2018 at 10:15:43PM +0100, SF Markus Elfring wrote:
> From: Markus Elfring <elfring@users.sourceforge.net>
> Date: Wed, 14 Mar 2018 22:02:52 +0100
>
> Move an assignment for a specific error code so that it is stored only once
> in this function implementation.
>
> This issue was detected by using the Coccinelle software.

How?

>
> Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
> ---
> drivers/media/i2c/ov5645.c | 6 +-----
> 1 file changed, 1 insertion(+), 5 deletions(-)
>
> diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c
> index d28845f7356f..374576380fd4 100644
> --- a/drivers/media/i2c/ov5645.c
> +++ b/drivers/media/i2c/ov5645.c
> @@ -1284,13 +1284,11 @@ static int ov5645_probe(struct i2c_client *client,
> ret = ov5645_read_reg(ov5645, OV5645_CHIP_ID_HIGH, &chip_id_high);
> if (ret < 0 || chip_id_high != OV5645_CHIP_ID_HIGH_BYTE) {
> dev_err(dev, "could not read ID high\n");
> - ret = -ENODEV;
> goto power_down;
> }
> ret = ov5645_read_reg(ov5645, OV5645_CHIP_ID_LOW, &chip_id_low);
> if (ret < 0 || chip_id_low != OV5645_CHIP_ID_LOW_BYTE) {
> dev_err(dev, "could not read ID low\n");
> - ret = -ENODEV;
> goto power_down;
> }
>
> @@ -1300,7 +1298,6 @@ static int ov5645_probe(struct i2c_client *client,
> &ov5645->aec_pk_manual);
> if (ret < 0) {
> dev_err(dev, "could not read AEC/AGC mode\n");
> - ret = -ENODEV;
> goto power_down;
> }
>
> @@ -1308,7 +1305,6 @@ static int ov5645_probe(struct i2c_client *client,
> &ov5645->timing_tc_reg20);
> if (ret < 0) {
> dev_err(dev, "could not read vflip value\n");
> - ret = -ENODEV;
> goto power_down;
> }
>
> @@ -1316,7 +1312,6 @@ static int ov5645_probe(struct i2c_client *client,
> &ov5645->timing_tc_reg21);
> if (ret < 0) {
> dev_err(dev, "could not read hflip value\n");
> - ret = -ENODEV;
> goto power_down;
> }
>
> @@ -1334,6 +1329,7 @@ static int ov5645_probe(struct i2c_client *client,
>
> power_down:
> ov5645_s_power(&ov5645->sd, false);
> + ret = -ENODEV;

I don't think this is where people would expect you to set the error code
in general. It should rather take place before goto, not after it. That'd
mean another variable, and I'm not convinced the result would improve the
driver.

> free_entity:
> media_entity_cleanup(&ov5645->sd.entity);
> free_ctrl:

--
Regards,

Sakari Ailus
sakari.ailus@linux.intel.com

\
 
 \ /
  Last update: 2018-03-14 23:18    [W:0.042 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site