lkml.org 
[lkml]   [2018]   [Mar]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/2] dt-bindings: phy: add support for STM32 USB PHY Controller (USBPHYC)
Date
This patch adds the device tree bindings description for STM32 USBPHYC
(USB PHY Controller).

Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
.../devicetree/bindings/phy/phy-stm32-usbphyc.txt | 46 ++++++++++++++++++++++
1 file changed, 46 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.txt b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.txt
new file mode 100644
index 0000000..1ad3893
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.txt
@@ -0,0 +1,46 @@
+STMicroelectronics STM32 USB HS PHY controller
+
+The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI
+switch. It controls PHY configuration and status, and the UTMI+ switch that
+selects either OTG or HOST controller for the second PHY port. It also sets
+PLL configuration.
+
+USBPHYC
+ |_ PLL
+ |
+ |_ PHY port#1 _________________ HOST controller
+ | _ |
+ | / 1|________________|
+ |_ PHY port#2 ----| |________________
+ | \_0| |
+ |_ UTMI switch_______| OTG controller
+
+
+Required properties:
+- compatible: must be "st,stm32mp1-usbphyc"
+- reg: address and length of the usb phy control register set
+- clocks: phandle + clock specifier for the PLL phy clock
+- phy-supply: from the generic phy bindings, phandle to the regulator
+ providing 3V3 power to the PHY, see phy-bindings.txt
+- vdda1v1-supply: phandle to the regulator providing 1V1 power to the PHY
+- vdda1v8-supply: phandle to the regulator providing 1V8 power to the PHY
+
+Optional properties:
+- assigned-clocks: phandle + clock specifier for the PLL phy clock
+- assigned-clock-parents: the PLL phy clock parent
+- resets: phandle + reset specifier
+- st,utmi-switch: should be <0> or <1>, to select USB controller for PHY
+ port#2. If not specified, 0 is the default selection.
+
+
+Example:
+ usbphyc: usb-phy@5a006000 {
+ compatible = "st,stm32mp1-usbphyc";
+ reg = <0x5a006000 0x1000>;
+ clocks = <&rcc_clk USBPHY_K>;
+ resets = <&rcc_rst USBPHY_R>;
+ st,utmi-switch = <1>;
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <&reg11>;
+ vdda1v8-supply = <&reg18>
+ };
--
2.7.4
\
 
 \ /
  Last update: 2018-03-01 16:37    [W:0.056 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site