lkml.org 
[lkml]   [2018]   [Feb]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v8 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)
On Tue, 27 Feb 2018 09:20:39 +0100
Philipp Zabel <p.zabel@pengutronix.de> wrote:

> On Tue, 2018-02-27 at 10:07 +0800, Yong Deng wrote:
> > Add binding documentation for Allwinner V3s CSI.
> >
> > Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
> > Reviewed-by: Rob Herring <robh@kernel.org>
> > Signed-off-by: Yong Deng <yong.deng@magewell.com>
> > ---
> > .../devicetree/bindings/media/sun6i-csi.txt | 59 ++++++++++++++++++++++
> > 1 file changed, 59 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > new file mode 100644
> > index 000000000000..2ff47a9507a6
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > @@ -0,0 +1,59 @@
> > +Allwinner V3s Camera Sensor Interface
> > +-------------------------------------
> > +
> > +Allwinner V3s SoC features two CSI module. CSI0 is used for MIPI CSI-2
> > +interface and CSI1 is used for parallel interface.
> > +
> > +Required properties:
> > + - compatible: value must be "allwinner,sun8i-v3s-csi"
> > + - reg: base address and size of the memory-mapped region.
> > + - interrupts: interrupt associated to this IP
> > + - clocks: phandles to the clocks feeding the CSI
> > + * bus: the CSI interface clock
> > + * mod: the CSI module clock
> > + * ram: the CSI DRAM clock
> > + - clock-names: the clock names mentioned above
> > + - resets: phandles to the reset line driving the CSI
> > +
> > +Each CSI node should contain one 'port' child node with one child 'endpoint'
> > +node, according to the bindings defined in
> > +Documentation/devicetree/bindings/media/video-interfaces.txt. As mentioned
> > +above, the endpoint's bus type should be MIPI CSI-2 for CSI0 and parallel or
> > +Bt656 for CSI1.
> > +
> > +Endpoint node properties for CSI1
> > +---------------------------------
> > +
> > +- remote-endpoint : (required) a phandle to the bus receiver's endpoint
> > + node
> > +- bus-width: : (required) must be 8, 10, 12 or 16
> > +- pclk-sample : (optional) (default: sample on falling edge)
>
> It would be helpful to state that 1 is rising edge and 0 is falling
> edge, see for example ov5640.txt

I think this is already documented at
Documentation/devicetree/bindings/media/video-interfaces.txt.

>
> regards
> Philipp


Thanks,
Yong

\
 
 \ /
  Last update: 2018-02-27 09:31    [W:0.059 / U:1.408 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site