lkml.org 
[lkml]   [2018]   [Feb]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 2/2] media: ov2680: Add Omnivision OV2680 sensor driver
Date
Hi Sakari,
Thanks for your review.

On Fri 23 Feb 2018 at 07:50, Sakari Ailus wrote:
> Hi Rui,
>
> On Thu, Feb 22, 2018 at 10:23:38AM +0000, Rui Miguel Silva
> wrote:
>> This patch adds V4L2 sub-device driver for OV2680 image sensor.
>> The OV2680 is a 1/5" CMOS color sensor from Omnivision.
>> Supports output format: 10-bit Raw RGB.
>> The OV2680 has a single lane MIPI interface.
>>
>> The driver exposes following V4L2 controls:
>> - auto/manual exposure,
>> - exposure,
>> - auto/manual gain,
>> - gain,
>> - horizontal/vertical flip,
>> - test pattern menu.
>> Supported resolution are only: QUXGA, 720P, UXGA.
>>
>> Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
>> ---
>> drivers/media/i2c/Kconfig | 13 +
>> drivers/media/i2c/Makefile | 1 +
>> drivers/media/i2c/ov2680.c | 1189
>> ++++++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 1203 insertions(+)
>> create mode 100644 drivers/media/i2c/ov2680.c
>>
>> diff --git a/drivers/media/i2c/Kconfig
>> b/drivers/media/i2c/Kconfig
>> index 9f18cd296841..089103d29171 100644
>> --- a/drivers/media/i2c/Kconfig
>> +++ b/drivers/media/i2c/Kconfig
>> @@ -586,6 +586,19 @@ config VIDEO_OV2659
>> To compile this driver as a module, choose M here: the
>> module will be called ov2659.
>>
>> +config VIDEO_OV2680
>> + tristate "OmniVision OV2680 sensor support"
>> + depends on OF
>
> I think you can drop OF dependency here.

Agree.

>
>> + depends on GPIOLIB && VIDEO_V4L2 && I2C &&
>> VIDEO_V4L2_SUBDEV_API
>> + depends on MEDIA_CAMERA_SUPPORT
>> + select V4L2_FWNODE
>> + ---help---
>> + This is a Video4Linux2 sensor-level driver for the
>> OmniVision
>> + OV2680 camera sensor with a MIPI CSI-2 interface.
>> +
>> + To compile this driver as a module, choose M here: the
>> + module will be called ov2680.
>> +
>> config VIDEO_OV5640
>> tristate "OmniVision OV5640 sensor support"
>> depends on OF
>> diff --git a/drivers/media/i2c/Makefile
>> b/drivers/media/i2c/Makefile
>> index c0f94cd8d56d..d0aba4d37b8d 100644
>> --- a/drivers/media/i2c/Makefile
>> +++ b/drivers/media/i2c/Makefile
>> @@ -61,6 +61,7 @@ obj-$(CONFIG_VIDEO_SONY_BTF_MPX) +=
>> sony-btf-mpx.o
>> obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
>> obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
>> obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
>> +obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
>> obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
>> obj-$(CONFIG_VIDEO_OV5645) += ov5645.o
>> obj-$(CONFIG_VIDEO_OV5647) += ov5647.o
>> diff --git a/drivers/media/i2c/ov2680.c
>> b/drivers/media/i2c/ov2680.c
>> new file mode 100644
>> index 000000000000..64c1c2b03f97
>> --- /dev/null
>> +++ b/drivers/media/i2c/ov2680.c
>> @@ -0,0 +1,1189 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Omnivision OV2680 CMOS Image Sensor driver
>> + *
>> + * Copyright (C) 2018 Linaro Ltd
>> + *
>> + * Based on OV5640 Sensor Driver
>> + * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All
>> Rights Reserved.
>> + * Copyright (C) 2014-2017 Mentor Graphics Inc.
>> + *
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/err.h>
>> +#include <linux/i2c.h>
>> +#include <linux/init.h>
>> +#include <linux/module.h>
>> +#include <linux/of_device.h>
>> +#include <linux/of_gpio.h>
>
> Do you need of_gpio.h?

Yeah, I need only to include the gpio/consumer.h for the
devm_gpiod_get_optional call.

>
>> +
>> +#include <media/v4l2-common.h>
>> +#include <media/v4l2-ctrls.h>
>> +#include <media/v4l2-device.h>
>> +#include <media/v4l2-event.h>
>> +#include <media/v4l2-fwnode.h>
>> +#include <media/v4l2-image-sizes.h>
>> +#include <media/v4l2-mediabus.h>
>> +#include <media/v4l2-subdev.h>
>
> Do you need all of these? At least v4l2-event.h and
> v4l2-image-sizes.h seem
> redundant.

Agree, will clean up this includes.

>
>> +
>> +#define OV2680_XVCLK_MIN 6000000
>> +#define OV2680_XVCLK_MAX 24000000
>> +
>> +#define OV2680_CHIP_ID_HIGH 0x26
>> +#define OV2680_CHIP_ID_LOW 0x80
>> +
>> +#define OV2680_REG_STREAM_CTRL 0x0100
>> +#define OV2680_REG_SOFT_RESET 0x0103
>> +
>> +#define OV2680_REG_CHIP_ID_HIGH 0x300a
>> +#define OV2680_REG_CHIP_ID_LOW 0x300b
>> +
>> +#define OV2680_REG_R_MANUAL 0x3503
>> +#define OV2680_REG_GAIN_PK 0x350a
>> +#define OV2680_REG_EXPOSURE_PK_HIGH 0x3500
>> +#define OV2680_REG_EXPOSURE_PK_MED 0x3501
>> +#define OV2680_REG_EXPOSURE_PK_LOW 0x3502
>> +#define OV2680_REG_TIMING_HTS 0x380c
>> +#define OV2680_REG_TIMING_VTS 0x380e
>> +#define OV2680_REG_FORMAT1 0x3820
>> +#define OV2680_REG_FORMAT2 0x3821
>> +
>> +#define OV2680_REG_ISP_CTRL00 0x5080
>> +
>> +enum ov2680_frame_rate {
>> + OV2680_30_FPS,
>> + OV2680_FRAMERATES_MAX,
>> +};
>> +
>> +static const int ov2680_framerates[] = {
>> + [OV2680_30_FPS] = 30,
>> +};
>> +
>> +enum ov2680_mode_id {
>> + OV2680_MODE_QUXGA_800_600,
>> + OV2680_MODE_720P_1280_720,
>> + OV2680_MODE_UXGA_1600_1200,
>> + OV2680_MODE_MAX,
>> +};
>> +
>> +struct reg_value {
>> + u16 reg_addr;
>> + u8 val;
>> +};
>> +
>> +struct ov2680_mode_info {
>> + const char *name;
>> + enum ov2680_mode_id id;
>> + u32 width;
>> + u32 height;
>> + const struct reg_value *reg_data;
>> + u32 reg_data_size;
>> +};
>> +
>> +struct ov2680_ctrls {
>> + struct v4l2_ctrl_handler handler;
>> + struct {
>> + struct v4l2_ctrl *auto_exp;
>> + struct v4l2_ctrl *exposure;
>> + };
>> + struct {
>> + struct v4l2_ctrl *auto_gain;
>> + struct v4l2_ctrl *gain;
>> + };
>> +
>> + struct v4l2_ctrl *hflip;
>> + struct v4l2_ctrl *vflip;
>> + struct v4l2_ctrl *test_pattern;
>> +};
>> +
>> +struct ov2680_dev {
>> + struct i2c_client *i2c_client;
>> + struct v4l2_subdev sd;
>> +
>> + struct media_pad pad;
>> + struct v4l2_fwnode_endpoint ep;
>> + struct clk *xvclk;
>> + u32 xvclk_freq;
>> +
>> + struct gpio_desc *pwdn_gpio;
>> + struct mutex lock; /* protect members
>> */
>> +
>> + bool mode_pending_changes;
>> + bool is_enabled;
>> + bool is_streaming;
>> +
>> + struct ov2680_ctrls ctrls;
>> + struct v4l2_mbus_framefmt fmt;
>> + struct v4l2_fract frame_interval;
>> +
>> + enum ov2680_frame_rate current_fps;
>> + const struct ov2680_mode_info *current_mode;
>> +};
>> +
>> +static const char * const test_pattern_menu[] = {
>> + "Disabled",
>> + "Color bars",
>
> "Color Bars",

right.

>
>> + "Random Data",
>> + "Square",
>> + "Black Image",
>> +};
>> +
>> +static const struct reg_value
>> ov2680_setting_30fps_QUXGA_800_600[] = {
>> + {0x3086, 0x01}, {0x370a, 0x23}, {0x3808, 0x03}, {0x3809,
>> 0x20},
>> + {0x380a, 0x02}, {0x380b, 0x58}, {0x380c, 0x06}, {0x380d,
>> 0xac},
>> + {0x380e, 0x02}, {0x380f, 0x84}, {0x3811, 0x04}, {0x3813,
>> 0x04},
>> + {0x3814, 0x31}, {0x3815, 0x31}, {0x3820, 0xc0}, {0x4008,
>> 0x00},
>> + {0x4009, 0x03}, {0x4837, 0x1e}, {0x3501, 0x4e}, {0x3502,
>> 0xe0},
>> +};
>> +
>> +static const struct reg_value
>> ov2680_setting_30fps_720P_1280_720[] = {
>> + {0x3086, 0x00}, {0x3808, 0x05}, {0x3809, 0x00}, {0x380a,
>> 0x02},
>> + {0x380b, 0xd0}, {0x380c, 0x06}, {0x380d, 0xa8}, {0x380e,
>> 0x05},
>> + {0x380f, 0x0e}, {0x3811, 0x08}, {0x3813, 0x06}, {0x3814,
>> 0x11},
>> + {0x3815, 0x11}, {0x3820, 0xc0}, {0x4008, 0x00},
>> +};
>> +
>> +static const struct reg_value
>> ov2680_setting_30fps_UXGA_1600_1200[] = {
>> + {0x3086, 0x00}, {0x3501, 0x4e}, {0x3502, 0xe0}, {0x3808,
>> 0x06},
>> + {0x3809, 0x40}, {0x380a, 0x04}, {0x380b, 0xb0}, {0x380c,
>> 0x06},
>> + {0x380d, 0xa8}, {0x380e, 0x05}, {0x380f, 0x0e}, {0x3811,
>> 0x00},
>> + {0x3813, 0x00}, {0x3814, 0x11}, {0x3815, 0x11}, {0x3820,
>> 0xc0},
>> + {0x4008, 0x00}, {0x4837, 0x18}
>> +};
>> +
>> +static const struct ov2680_mode_info ov2680_mode_init_data = {
>> + "mode_quxga_800_600", OV2680_MODE_QUXGA_800_600, 800, 600,
>> + ov2680_setting_30fps_QUXGA_800_600,
>> + ARRAY_SIZE(ov2680_setting_30fps_QUXGA_800_600),
>> +};
>> +
>> +static const struct ov2680_mode_info
>> +ov2680_mode_data[OV2680_FRAMERATES_MAX][OV2680_MODE_MAX] = {
>
> You only have a single frame rate. Do you plan to support more?

Not for now.

>
> As the frame rate is specific to a mode rather than the other
> way around, I
> think you should probably swap the array dimensions. You could
> even remove
> this as frame rate selection clearly isn't implemented in the
> driver.

I was thinking to have this more generic to add afterwards others
frame rate, but i will drop it for now.

>
>> + {
>> + {"mode_quxga_800_600", OV2680_MODE_QUXGA_800_600,
>> + 800, 600, ov2680_setting_30fps_QUXGA_800_600,
>> + ARRAY_SIZE(ov2680_setting_30fps_QUXGA_800_600)},
>> + {"mode_720p_1280_720", OV2680_MODE_720P_1280_720,
>> + 1280, 720, ov2680_setting_30fps_720P_1280_720,
>> + ARRAY_SIZE(ov2680_setting_30fps_720P_1280_720)},
>> + {"mode_uxga_1600_1200",
>> OV2680_MODE_UXGA_1600_1200,
>> + 1600, 1200, ov2680_setting_30fps_UXGA_1600_1200,
>> + ARRAY_SIZE(ov2680_setting_30fps_UXGA_1600_1200)},
>> + },
>> +};
>> +
>> +static struct ov2680_dev *to_ov2680_dev(struct v4l2_subdev
>> *sd)
>> +{
>> + return container_of(sd, struct ov2680_dev, sd);
>> +}
>> +
>> +static struct device *ov2680_to_dev(struct ov2680_dev *sensor)
>> +{
>> + return &sensor->i2c_client->dev;
>> +}
>> +
>> +static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl
>> *ctrl)
>> +{
>> + return &container_of(ctrl->handler, struct ov2680_dev,
>> + ctrls.handler)->sd;
>> +}
>> +
>> +static int ov2680_write_reg(struct ov2680_dev *sensor, u16
>> reg, u8 val)
>> +{
>> + struct i2c_client *client = sensor->i2c_client;
>> + struct i2c_msg msg;
>> + u8 buf[3];
>> + int ret;
>> +
>> + buf[0] = reg >> 8;
>> + buf[1] = reg & 0xff;
>> + buf[2] = val;
>> +
>> + msg.addr = client->addr;
>> + msg.flags = client->flags;
>> + msg.buf = buf;
>> + msg.len = sizeof(buf);
>> +
>> + ret = i2c_transfer(client->adapter, &msg, 1);
>> + if (ret < 0) {
>> + dev_err(&client->dev, "write error: reg=0x%4x:
>> %d\n", reg, ret);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_write_reg16(struct ov2680_dev *sensor, u16
>> reg, u16 val)
>> +{
>> + int ret;
>> +
>> + ret = ov2680_write_reg(sensor, reg, val >> 8);
>> + if (ret)
>> + return ret;
>> +
>> + return ov2680_write_reg(sensor, reg + 1, val & 0xff);
>> +}
>> +
>> +static int ov2680_read_reg(struct ov2680_dev *sensor, u16 reg,
>> u8 *val)
>> +{
>> + struct i2c_client *client = sensor->i2c_client;
>> + struct i2c_msg msg[2];
>> + u8 buf[2];
>> + int ret;
>> +
>> + buf[0] = reg >> 8;
>> + buf[1] = reg & 0xff;
>> +
>> + msg[0].addr = client->addr;
>> + msg[0].flags = client->flags;
>> + msg[0].buf = buf;
>> + msg[0].len = sizeof(buf);
>> +
>> + msg[1].addr = client->addr;
>> + msg[1].flags = client->flags | I2C_M_RD;
>> + msg[1].buf = buf;
>> + msg[1].len = 1;
>> +
>> + ret = i2c_transfer(client->adapter, msg, 2);
>> + if (ret < 0) {
>> + dev_err(&client->dev, "read error: reg=0x%4x:
>> %d\n", reg, ret);
>> + return ret;
>> + }
>> +
>> + *val = buf[0];
>> + return 0;
>> +}
>> +
>> +static int ov2680_read_reg16(struct ov2680_dev *sensor, u16
>> reg, u16 *val)
>> +{
>> + u8 hi, lo;
>> + int ret;
>> +
>> + ret = ov2680_read_reg(sensor, reg, &hi);
>> + if (ret)
>> + return ret;
>> + ret = ov2680_read_reg(sensor, reg + 1, &lo);
>> + if (ret)
>> + return ret;
>
> You shouldn't implement accessing 16-bit registers like this
> neither for
> reading or writing unless there's a specific reason to do so.
> Just access
> the high and low octet in the same transaction.

Agree.

>
>> +
>> + *val = ((u16)hi << 8) | (u16)lo;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_mod_reg(struct ov2680_dev *sensor, u16 reg,
>> u8 mask, u8 val)
>> +{
>> + u8 readval;
>> + int ret;
>> +
>> + ret = ov2680_read_reg(sensor, reg, &readval);
>> + if (ret < 0)
>> + return ret;
>> +
>> + readval &= ~mask;
>> + val &= mask;
>> + val |= readval;
>> +
>> + return ov2680_write_reg(sensor, reg, val);
>> +}
>> +
>> +static int ov2680_load_regs(struct ov2680_dev *sensor,
>> + const struct ov2680_mode_info *mode)
>> +{
>> + const struct reg_value *regs = mode->reg_data;
>> + unsigned int i;
>> + int ret = 0;
>> + u16 reg_addr;
>> + u8 val;
>> +
>> + for (i = 0; i < mode->reg_data_size; ++i, ++regs) {
>> + reg_addr = regs->reg_addr;
>> + val = regs->val;
>> +
>> + ret = ov2680_write_reg(sensor, reg_addr, val);
>> + if (ret)
>> + break;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static void ov2680_power_up(struct ov2680_dev *sensor)
>> +{
>> + if (!sensor->pwdn_gpio)
>> + return;
>> +
>> + gpiod_set_value(sensor->pwdn_gpio, 1);
>> + usleep_range(5000, 10000);
>> +}
>
> Even if you're using GPIO only right now, the power up and power
> down
> may not be executed before the corresponding power up sequence.
>
>> +
>> +static void ov2680_power_down(struct ov2680_dev *sensor)
>> +{
>> + if (!sensor->pwdn_gpio)
>> + return;
>> +
>> + gpiod_set_value(sensor->pwdn_gpio, 0);
>> + usleep_range(5000, 10000);
>> +}
>> +
>> +static int ov2680_soft_reset(struct ov2680_dev *sensor)
>> +{
>> + struct device *dev = ov2680_to_dev(sensor);
>> + int ret;
>> +
>> + ret = ov2680_write_reg(sensor, OV2680_REG_SOFT_RESET,
>> 0x01);
>> + if (ret != 0) {
>> + dev_err(dev, "sensor soft reset failed\n");
>> + return ret;
>> + }
>> + usleep_range(1000, 2000);
>> + return 0;
>> +}
>> +
>> +static void ov2680_reset(struct ov2680_dev *sensor)
>> +{
>> + if (!sensor->pwdn_gpio) {
>> + ov2680_soft_reset(sensor);
>> + return;
>> + }
>> +
>> + ov2680_power_down(sensor);
>> + ov2680_power_up(sensor);
>
> Please merge the two above functions to ov2670_enable. That
> might be better
> called e.g. ov2670_power_on. Likewise ov2670_disable could be
> ov2670_power_off. These functions are implementing power on and
> power off
> sequences after all.

Other than s/ov2670/ov2680/ in your comment ;), I agree and will
merge the
power/enable sequences.

>
>> +}
>> +
>> +static int ov2680_vflip_enable(struct ov2680_dev *sensor)
>> +{
>> + return ov2680_mod_reg(sensor, OV2680_REG_FORMAT1, BIT(2),
>> BIT(2));
>> +}
>> +
>> +static int ov2680_vflip_disable(struct ov2680_dev *sensor)
>> +{
>> + return ov2680_mod_reg(sensor, OV2680_REG_FORMAT1, BIT(2),
>> 0);
>> +}
>> +
>> +static int ov2680_hflip_enable(struct ov2680_dev *sensor)
>> +{
>> + return ov2680_mod_reg(sensor, OV2680_REG_FORMAT2, BIT(2),
>> BIT(2));
>> +}
>> +
>> +static int ov2680_hflip_disable(struct ov2680_dev *sensor)
>> +{
>> + return ov2680_mod_reg(sensor, OV2680_REG_FORMAT2, BIT(2),
>> 0);
>> +}
>> +
>> +static int ov2680_test_pattern_set(struct ov2680_dev *sensor,
>> int value)
>> +{
>> + int ret;
>> +
>> + if (!value)
>> + return ov2680_mod_reg(sensor,
>> OV2680_REG_ISP_CTRL00, BIT(7), 0);
>> +
>> + ret = ov2680_mod_reg(sensor, OV2680_REG_ISP_CTRL00, 0x03,
>> value - 1);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = ov2680_mod_reg(sensor, OV2680_REG_ISP_CTRL00,
>> BIT(7), BIT(7));
>> + if (ret < 0)
>> + return ret;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_gain_set(struct ov2680_dev *sensor, bool
>> auto_gain)
>> +{
>> + struct ov2680_ctrls *ctrls = &sensor->ctrls;
>> + u16 gain;
>> + int ret;
>> +
>> + ret = ov2680_mod_reg(sensor, OV2680_REG_R_MANUAL, BIT(1),
>> + auto_gain ? 0 : BIT(1));
>> + if (ret < 0)
>> + return ret;
>> +
>> + if (auto_gain)
>> + return 0;
>> +
>> + gain = (u16)ctrls->gain->val;
>> +
>> + ret = ov2680_write_reg16(sensor, OV2680_REG_GAIN_PK, gain
>> & 0x7ff);
>
> I think you could just use ctrls->gain->val here.
>
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_gain_get(struct ov2680_dev *sensor)
>> +{
>> + u16 gain;
>> + int ret;
>> +
>> + ret = ov2680_read_reg16(sensor, OV2680_REG_GAIN_PK,
>> &gain);
>> + if (ret)
>> + return ret;
>> +
>> + return gain & 0x3ff;
>
> Why 3ff here but 7ff when setting the gain?

is 0x7ff in both.

>
>> +}
>> +
>> +static int ov2680_auto_gain_enable(struct ov2680_dev *sensor)
>> +{
>> + return ov2680_gain_set(sensor, true);
>> +}
>> +
>> +static int ov2680_auto_gain_disable(struct ov2680_dev *sensor)
>> +{
>> + return ov2680_gain_set(sensor, false);
>> +}
>
> Could you use ov2680_gain_set() from the caller instead? Perhaps
> rename it
> as ov2680_autogain_set()?

Ack.

>
>> +
>> +static int ov2680_exposure_set(struct ov2680_dev *sensor, bool
>> auto_exp)
>> +{
>> + struct ov2680_ctrls *ctrls = &sensor->ctrls;
>> + u32 exp;
>> + int ret;
>> +
>> + ret = ov2680_mod_reg(sensor, OV2680_REG_R_MANUAL, BIT(0),
>> + auto_exp ? 0 : BIT(0));
>> + if (ret < 0)
>> + return ret;
>> +
>> + if (auto_exp)
>> + return 0;
>> +
>> + exp = (u32)ctrls->exposure->val;
>> + exp <<= 4;
>> +
>> + ret = ov2680_write_reg(sensor, OV2680_REG_EXPOSURE_PK_LOW,
>> exp & 0xf0);
>> + if (ret)
>> + return ret;
>> +
>> + ret = ov2680_write_reg(sensor, OV2680_REG_EXPOSURE_PK_MED,
>> + (exp >> 8) & 0xff);
>> + if (ret)
>> + return ret;
>> +
>> + return ov2680_write_reg(sensor,
>> OV2680_REG_EXPOSURE_PK_HIGH,
>> + (exp >> 16) & 0x0f);
>
> I'd suppose you'll get interesting effects if the exposure
> latching point
> happens to be in between these updates.
>
> A single read would avoid that. Or is there a particular reason
> to perform
> a read of a single register in three transactions?

No, I will implement a single transaction.

>
>> +}
>> +
>> +static int ov2680_exposure_get(struct ov2680_dev *sensor)
>> +{
>> + int exp, ret;
>> + u8 temp;
>> +
>> + ret = ov2680_read_reg(sensor, OV2680_REG_EXPOSURE_PK_HIGH,
>> &temp);
>> + if (ret)
>> + return ret;
>> + exp = ((int)temp & 0x0f) << 16;
>> +
>> + ret = ov2680_read_reg(sensor, OV2680_REG_EXPOSURE_PK_MED,
>> &temp);
>> + if (ret)
>> + return ret;
>> + exp |= ((int)temp & 0xff) << 8;
>> +
>> + ret = ov2680_read_reg(sensor, OV2680_REG_EXPOSURE_PK_LOW,
>> &temp);
>> + if (ret)
>> + return ret;
>> + exp |= ((int)temp & 0xf0);
>> +
>> + return exp >> 4;
>> +}
>> +
>> +static int ov2680_auto_exposure_enable(struct ov2680_dev
>> *sensor)
>> +{
>> + return ov2680_exposure_set(sensor, true);
>> +}
>> +
>> +static int ov2680_auto_exposure_disable(struct ov2680_dev
>> *sensor)
>> +{
>> + return ov2680_exposure_set(sensor, false);
>> +}
>
> Same for exposure.

ditto.

>
>> +
>> +static int ov2680_stream_enable(struct ov2680_dev *sensor)
>> +{
>> + return ov2680_write_reg(sensor, OV2680_REG_STREAM_CTRL,
>> 1);
>> +}
>> +
>> +static int ov2680_stream_disable(struct ov2680_dev *sensor)
>> +{
>> + return ov2680_write_reg(sensor, OV2680_REG_STREAM_CTRL,
>> 0);
>> +}
>> +
>> +static int ov2680_mode_set_direct(struct ov2680_dev *sensor)
>> +{
>> + int ret;
>> +
>> + if (!sensor->current_mode->reg_data)
>> + return -EINVAL;
>> +
>> + ret = ov2680_load_regs(sensor, sensor->current_mode);
>> + if (ret < 0)
>> + return ret;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_mode_set(struct ov2680_dev *sensor)
>> +{
>> + int ret;
>> +
>> + ret = ov2680_auto_gain_disable(sensor);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = ov2680_auto_exposure_disable(sensor);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = ov2680_mode_set_direct(sensor);
>
> ov2680_mode_set_direct() is only used here. How about moving the
> contents
> here?

LGTM

>
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = ov2680_auto_gain_enable(sensor);
>
> This should be based on the control value, shouldn't it?

Yup.

>
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = ov2680_auto_exposure_enable(sensor);
>> + if (ret < 0)
>> + return ret;
>
> As well as the exposure.

ditto.

>
>> +
>> + sensor->mode_pending_changes = false;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_mode_restore(struct ov2680_dev *sensor)
>> +{
>> + int ret;
>> +
>> + ret = ov2680_load_regs(sensor, &ov2680_mode_init_data);
>> + if (ret < 0)
>> + return ret;
>> +
>> + return ov2680_mode_set(sensor);
>> +}
>> +
>> +static int ov2680_disable(struct ov2680_dev *sensor)
>> +{
>> + if (!sensor->is_enabled)
>> + return 0;
>> +
>> + clk_disable_unprepare(sensor->xvclk);
>> + ov2680_power_down(sensor);
>> + sensor->is_enabled = false;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_enable(struct ov2680_dev *sensor)
>> +{
>> + struct device *dev = ov2680_to_dev(sensor);
>> + int ret;
>> +
>> + if (sensor->is_enabled)
>> + return 0;
>> +
>> + ov2680_reset(sensor);
>> +
>> + ret = clk_prepare_enable(sensor->xvclk);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = ov2680_mode_restore(sensor);
>> + if (ret < 0)
>> + goto disable;
>> +
>> + sensor->is_enabled = true;
>> +
>> + /* Set clock lane into LP-11 state */
>> + ov2680_stream_enable(sensor);
>> + usleep_range(1000, 2000);
>> + ov2680_stream_disable(sensor);
>> +
>> + return 0;
>> +
>> +disable:
>> + dev_err(dev, "failed to enable sensor: %d\n", ret);
>> + ov2680_disable(sensor);
>> +
>> + return ret;
>> +}
>> +
>> +static int ov2680_s_power(struct v4l2_subdev *sd, int on)
>> +{
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> + int ret = 0;
>> +
>> + mutex_lock(&sensor->lock);
>> +
>> + if (on)
>> + ret = ov2680_enable(sensor);
>> + else
>> + ret = ov2680_disable(sensor);
>> +
>> + mutex_unlock(&sensor->lock);
>> +
>> + if (on && ret == 0) {
>> + ret =
>> v4l2_ctrl_handler_setup(&sensor->ctrls.handler);
>> + if (ret < 0)
>> + return ret;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static int ov2680_g_frame_interval(struct v4l2_subdev *sd,
>> + struct
>> v4l2_subdev_frame_interval *fi)
>> +{
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> +
>> + mutex_lock(&sensor->lock);
>> + fi->interval = sensor->frame_interval;
>> + mutex_unlock(&sensor->lock);
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_s_frame_interval(struct v4l2_subdev *sd,
>> + struct
>> v4l2_subdev_frame_interval *fi)
>> +{
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> +
>> + if (fi->interval.denominator !=
>> sensor->frame_interval.denominator ||
>> + fi->interval.numerator !=
>> sensor->frame_interval.numerator)
>
> You only support 30 frames per second. Even then, you need to
> modify the
> request to match with what the driver supports, so the
> implementation can
> be the same than for g_frame_interval.

Ack.

>
>> + return -EINVAL;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_s_stream(struct v4l2_subdev *sd, int enable)
>> +{
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> + int ret = 0;
>> +
>> + mutex_lock(&sensor->lock);
>> +
>> + if (sensor->is_streaming == !!enable)
>> + goto unlock;
>> +
>> + if (enable && sensor->mode_pending_changes) {
>> + ret = ov2680_mode_set(sensor);
>> + if (ret < 0)
>> + goto unlock;
>> + }
>> +
>> + if (enable)
>> + ret = ov2680_stream_enable(sensor);
>> + else
>> + ret = ov2680_stream_disable(sensor);
>> +
>> + sensor->is_streaming = !!enable;
>> +
>> +unlock:
>> + mutex_unlock(&sensor->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int ov2680_enum_mbus_code(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config
>> *cfg,
>> + struct v4l2_subdev_mbus_code_enum
>> *code)
>> +{
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> +
>> + if (code->pad != 0 || code->index != 0)
>> + return -EINVAL;
>> +
>> + code->code = sensor->fmt.code;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_get_fmt(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config *cfg,
>> + struct v4l2_subdev_format *format)
>> +{
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> + struct v4l2_mbus_framefmt *fmt;
>> +
>> + if (format->pad != 0)
>> + return -EINVAL;
>> +
>> + mutex_lock(&sensor->lock);
>> +
>> + if (format->which == V4L2_SUBDEV_FORMAT_TRY)
>> + fmt = v4l2_subdev_get_try_format(&sensor->sd, cfg,
>> format->pad);
>> + else
>> + fmt = &sensor->fmt;
>> +
>> + format->format = *fmt;
>> +
>> + mutex_unlock(&sensor->lock);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct ov2680_mode_info *
>> +ov2680_mode_find(struct ov2680_dev *sensor, enum
>> ov2680_frame_rate fps,
>> + int width, int height)
>> +{
>> + const struct ov2680_mode_info *mode = NULL;
>> + bool mode_found = false;
>> + int i;
>> +
>> + for (i = OV2680_MODE_MAX - 1; i >= 0; i--) {
>> + mode = &ov2680_mode_data[fps][i];
>> +
>> + if (!mode->reg_data)
>> + continue;
>> +
>> + if (mode->width == width && mode->height ==
>> height) {
>
> The closest match would be better. Can you use this? I'm
> planning to send a
> pull request on the set soon.
>
> <URL:https://patchwork.linuxtv.org/patch/46975/>

Yeah, I saw your patch in list already, I was waiting to be
pulled. I
will use it, makes sense.

>
>> + mode_found = true;
>> + break;
>> + }
>> + }
>> +
>> + return mode_found ? mode : NULL;
>> +}
>> +
>> +static int ov2680_set_fmt(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config *cfg,
>> + struct v4l2_subdev_format *format)
>> +{
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> + struct v4l2_mbus_framefmt *fmt = &format->format;
>> + const struct ov2680_mode_info *mode;
>> + int ret = 0;
>> +
>> + if (format->pad != 0)
>> + return -EINVAL;
>> +
>> + mutex_lock(&sensor->lock);
>> +
>> + if (sensor->is_streaming) {
>> + ret = -EBUSY;
>> + goto unlock;
>> + }
>> +
>> + mode = ov2680_mode_find(sensor, sensor->current_fps,
>> fmt->width,
>> + fmt->height);
>> + if (!mode) {
>> + ret = -EINVAL;
>> + goto unlock;
>> + }
>> +
>> + if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
>> + fmt = v4l2_subdev_get_try_format(sd, cfg, 0);
>> +
>> + *fmt = format->format;
>> + goto unlock;
>> + }
>> +
>> + fmt->width = mode->width;
>> + fmt->height = mode->height;
>> + fmt->code = sensor->fmt.code;
>> + fmt->colorspace = sensor->fmt.colorspace;
>> +
>> + sensor->current_mode = mode;
>> + sensor->fmt = format->format;
>> + sensor->mode_pending_changes = true;
>> +
>> +unlock:
>> + mutex_unlock(&sensor->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int ov2680_enum_frame_size(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config
>> *cfg,
>> + struct
>> v4l2_subdev_frame_size_enum *fse)
>> +{
>> + int index = fse->index;
>> +
>> + if (index >= OV2680_MODE_MAX)
>> + return -EINVAL;
>> +
>> + fse->min_width = ov2680_mode_data[0][index].width;
>> + fse->min_height = ov2680_mode_data[0][index].height;
>> + fse->max_width = ov2680_mode_data[0][index].width;
>> + fse->max_height = ov2680_mode_data[0][index].height;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_enum_frame_interval(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config *cfg,
>> + struct
>> v4l2_subdev_frame_interval_enum *fie)
>> +{
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> + const struct ov2680_mode_info *mode;
>> + struct v4l2_fract tpf;
>> +
>> + if (fie->index >= OV2680_FRAMERATES_MAX)
>> + return -EINVAL;
>> +
>> + tpf.denominator = ov2680_framerates[fie->index];
>> + tpf.numerator = 1;
>> +
>> + fie->interval = tpf;
>> +
>> + mode = ov2680_mode_find(sensor, sensor->current_fps,
>> fie->width,
>> + fie->height);
>> +
>> + return mode ? 0 : -EINVAL;
>> +}
>> +
>> +static int ov2680_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
>> +{
>> + struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> + int val;
>> +
>> + if (!sensor->is_enabled)
>> + return 0;
>> +
>> + switch (ctrl->id) {
>> + case V4L2_CID_AUTOGAIN:
>> + if (!ctrl->val)
>> + return 0;
>> + val = ov2680_gain_get(sensor);
>> + if (val < 0)
>> + return val;
>> + sensor->ctrls.gain->val = val;
>> + break;
>> + case V4L2_CID_EXPOSURE_AUTO:
>> + if (ctrl->val == V4L2_EXPOSURE_MANUAL)
>> + return 0;
>> + val = ov2680_exposure_get(sensor);
>> + if (val < 0)
>> + return val;
>> + sensor->ctrls.exposure->val = val;
>> + break;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_s_ctrl(struct v4l2_ctrl *ctrl)
>> +{
>> + struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> +
>> + if (!sensor->is_enabled)
>> + return 0;
>> +
>> + switch (ctrl->id) {
>> + case V4L2_CID_AUTOGAIN:
>> + return ov2680_gain_set(sensor, !!ctrl->val);
>> + case V4L2_CID_EXPOSURE_AUTO:
>> + return ov2680_exposure_set(sensor, !!ctrl->val);
>> + case V4L2_CID_VFLIP:
>> + if (ctrl->val)
>> + return ov2680_vflip_enable(sensor);
>> + else
>> + return ov2680_vflip_disable(sensor);
>> + case V4L2_CID_HFLIP:
>> + if (ctrl->val)
>> + return ov2680_hflip_enable(sensor);
>> + else
>> + return ov2680_hflip_disable(sensor);
>> + case V4L2_CID_TEST_PATTERN:
>> + return ov2680_test_pattern_set(sensor, ctrl->val);
>> + default:
>> + break;
>> + }
>> +
>> + return -EINVAL;
>> +}
>> +
>> +static const struct v4l2_ctrl_ops ov2680_ctrl_ops = {
>> + .g_volatile_ctrl = ov2680_g_volatile_ctrl,
>> + .s_ctrl = ov2680_s_ctrl,
>> +};
>> +
>> +static const struct v4l2_subdev_core_ops ov2680_core_ops = {
>> + .s_power = ov2680_s_power,
>> +};
>> +
>> +static const struct v4l2_subdev_video_ops ov2680_video_ops = {
>> + .g_frame_interval = ov2680_g_frame_interval,
>> + .s_frame_interval = ov2680_s_frame_interval,
>> + .s_stream = ov2680_s_stream,
>> +};
>> +
>> +static const struct v4l2_subdev_pad_ops ov2680_pad_ops = {
>> + .enum_mbus_code = ov2680_enum_mbus_code,
>> + .get_fmt = ov2680_get_fmt,
>> + .set_fmt = ov2680_set_fmt,
>> + .enum_frame_size = ov2680_enum_frame_size,
>> + .enum_frame_interval = ov2680_enum_frame_interval,
>> +};
>> +
>> +static const struct v4l2_subdev_ops ov2680_subdev_ops = {
>> + .core = &ov2680_core_ops,
>> + .video = &ov2680_video_ops,
>> + .pad = &ov2680_pad_ops,
>> +};
>> +
>> +static int ov2680_mode_init(struct ov2680_dev *sensor)
>> +{
>> + const struct ov2680_mode_info *init_mode;
>> +
>> + /* set initial mode */
>> + sensor->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
>> + sensor->fmt.width = 800;
>> + sensor->fmt.height = 600;
>> + sensor->fmt.field = V4L2_FIELD_NONE;
>> + sensor->fmt.colorspace = V4L2_COLORSPACE_SRGB;
>> +
>> + sensor->frame_interval.denominator =
>> ov2680_framerates[OV2680_30_FPS];
>> + sensor->frame_interval.numerator = 1;
>> +
>> + sensor->current_fps = OV2680_30_FPS;
>> + init_mode =
>> &ov2680_mode_data[OV2680_30_FPS][OV2680_MODE_QUXGA_800_600];
>> +
>> + sensor->current_mode = init_mode;
>> +
>> + sensor->mode_pending_changes = true;
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_v4l2_init(struct ov2680_dev *sensor)
>> +{
>> + const struct v4l2_ctrl_ops *ops = &ov2680_ctrl_ops;
>> + struct ov2680_ctrls *ctrls = &sensor->ctrls;
>> + struct v4l2_ctrl_handler *hdl = &ctrls->handler;
>> + int ret = 0;
>> +
>> + v4l2_i2c_subdev_init(&sensor->sd, sensor->i2c_client,
>> + &ov2680_subdev_ops);
>> +
>> + sensor->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
>> + sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
>> + sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
>> +
>> + ret = media_entity_pads_init(&sensor->sd.entity, 1,
>> &sensor->pad);
>> + if (ret < 0)
>> + return ret;
>> +
>> + v4l2_ctrl_handler_init(hdl, 32);
>> +
>> + hdl->lock = &sensor->lock;
>> +
>> + ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP,
>> 0, 1, 1, 0);
>> + ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP,
>> 0, 1, 1, 0);
>> +
>> + ctrls->test_pattern = v4l2_ctrl_new_std_menu_items(hdl,
>> + &ov2680_ctrl_ops,
>> + V4L2_CID_TEST_PATTERN,
>> +
>> ARRAY_SIZE(test_pattern_menu) - 1,
>> + 0, 0, test_pattern_menu);
>> +
>> + ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops,
>> +
>> V4L2_CID_EXPOSURE_AUTO,
>> +
>> V4L2_EXPOSURE_MANUAL, 0,
>> +
>> V4L2_EXPOSURE_AUTO);
>> +
>> + ctrls->exposure = v4l2_ctrl_new_std(hdl, ops,
>> V4L2_CID_EXPOSURE,
>> + 0, 32767, 1, 0);
>> +
>> + ctrls->auto_gain = v4l2_ctrl_new_std(hdl, ops,
>> V4L2_CID_AUTOGAIN,
>> + 0, 1, 1, 1);
>> + ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN,
>> 0, 2047, 1, 0);
>> +
>> + ctrls->gain->flags |= V4L2_CTRL_FLAG_VOLATILE;
>> + ctrls->exposure->flags |= V4L2_CTRL_FLAG_VOLATILE;
>
> v4l2_ctrl_new_std() may return NULL. Please check gain and
> exposure are
> non-NULL before dereferencing them. The error handling seems
> fine
> otherwise.

Ack.

>
>> +
>> + v4l2_ctrl_auto_cluster(2, &ctrls->auto_gain, 1, true);
>> + v4l2_ctrl_auto_cluster(2, &ctrls->auto_exp, 1, true);
>> +
>> + sensor->sd.ctrl_handler = hdl;
>> +
>> + ret = v4l2_async_register_subdev(&sensor->sd);
>> + if (ret < 0) {
>> + media_entity_cleanup(&sensor->sd.entity);
>> + v4l2_ctrl_handler_free(hdl);
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static int ov2680_check_id(struct ov2680_dev *sensor)
>> +{
>> + struct device *dev = ov2680_to_dev(sensor);
>> + u8 chip_id_high;
>> + u8 chip_id_low;
>> + int ret;
>> +
>> + ov2680_reset(sensor);
>
> I don't have the sensor datasheet, but practically everywhere
> you'll need
> execute the power up sequence before accessing the sensor
> registers.

Agree.

>
>> +
>> + ret = ov2680_read_reg(sensor, OV2680_REG_CHIP_ID_HIGH,
>> &chip_id_high);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to read chip id high\n");
>> + return -ENODEV;
>> + }
>> +
>> + ret = ov2680_read_reg(sensor, OV2680_REG_CHIP_ID_LOW,
>> &chip_id_low);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to read chip id low\n");
>> + return -ENODEV;
>> + }
>> +
>> + if (chip_id_high != OV2680_CHIP_ID_HIGH ||
>> + chip_id_low != OV2680_CHIP_ID_LOW) {
>> + dev_err(dev, "chip id: 0x%02x%02x does not match
>> expected: 0x%02x%02x\n",
>> + chip_id_high, chip_id_low,
>> OV2680_CHIP_ID_HIGH,
>> + OV2680_CHIP_ID_LOW);
>> + return -ENODEV;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2860_parse_dt(struct ov2680_dev *sensor)
>> +{
>> + struct device *dev = ov2680_to_dev(sensor);
>> + int ret;
>> +
>> + sensor->pwdn_gpio = devm_gpiod_get_optional(dev,
>> "powerdown",
>> +
>> GPIOD_OUT_HIGH);
>> + ret = PTR_ERR_OR_ZERO(sensor->pwdn_gpio);
>> + if (ret < 0) {
>> + dev_dbg(dev, "error while getting powerdown gpio:
>> %d\n", ret);
>> + return ret;
>> + }
>> +
>> + sensor->xvclk = devm_clk_get(dev, "xvclk");
>> + if (IS_ERR(sensor->xvclk)) {
>> + dev_err(dev, "xvclk clock missing or invalid\n");
>> + return PTR_ERR(sensor->xvclk);
>> + }
>> +
>> + sensor->xvclk_freq = clk_get_rate(sensor->xvclk);
>> + if (sensor->xvclk_freq < OV2680_XVCLK_MIN ||
>> + sensor->xvclk_freq > OV2680_XVCLK_MAX) {
>
> I believe the register lists are intended for a particular
> frequency and do
> not work for others. What is this frequency?

24MHz

I will prepare v2 with the above reviews. Once again many thanks.

---
Cheers,
Rui


>
>> + dev_err(dev, "xvclk frequency out of range: %d
>> Hz\n",
>> + sensor->xvclk_freq);
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int ov2680_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct device *dev = &client->dev;
>> + struct ov2680_dev *sensor;
>> + int ret;
>> +
>> + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
>> + if (!sensor)
>> + return -ENOMEM;
>> +
>> + sensor->i2c_client = client;
>> +
>> + ret = ov2860_parse_dt(sensor);
>> + if (ret < 0)
>> + return -EINVAL;
>> +
>> + ret = ov2680_check_id(sensor);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = ov2680_mode_init(sensor);
>> + if (ret < 0)
>> + return ret;
>> +
>> + mutex_init(&sensor->lock);
>> +
>> + ret = ov2680_v4l2_init(sensor);
>> + if (ret < 0)
>> + goto lock_destroy;
>> +
>> + dev_info(dev, "ov2680 init correctly\n");
>> +
>> + return 0;
>> +
>> +lock_destroy:
>> + mutex_destroy(&sensor->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int ov2680_remove(struct i2c_client *client)
>> +{
>> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> +
>> + v4l2_async_unregister_subdev(&sensor->sd);
>> + mutex_destroy(&sensor->lock);
>> + media_entity_cleanup(&sensor->sd.entity);
>> + v4l2_ctrl_handler_free(&sensor->ctrls.handler);
>> +
>> + return 0;
>> +}
>> +
>> +static int __maybe_unused ov2680_suspend(struct device *dev)
>> +{
>> + struct i2c_client *client = to_i2c_client(dev);
>> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> +
>> + if (sensor->is_streaming)
>> + ov2680_stream_disable(sensor);
>> +
>> + return 0;
>> +}
>> +
>> +static int __maybe_unused ov2680_resume(struct device *dev)
>> +{
>> + struct i2c_client *client = to_i2c_client(dev);
>> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
>> + struct ov2680_dev *sensor = to_ov2680_dev(sd);
>> + int ret;
>> +
>> + if (sensor->is_streaming) {
>> + ret = ov2680_stream_enable(sensor);
>> + if (ret < 0)
>> + goto stream_disable;
>> + }
>> +
>> + return 0;
>> +
>> +stream_disable:
>> + ov2680_stream_disable(sensor);
>> + sensor->is_streaming = false;
>> +
>> + return ret;
>> +}
>> +
>> +static const struct dev_pm_ops ov2680_pm_ops = {
>> + SET_SYSTEM_SLEEP_PM_OPS(ov2680_suspend, ov2680_resume)
>> +};
>> +
>> +static const struct i2c_device_id ov2680_id[] = {
>> + {"ov2680", 0},
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(i2c, ov2680_id);
>> +
>> +static const struct of_device_id ov2680_dt_ids[] = {
>> + { .compatible = "ovti,ov2680" },
>> + { /* sentinel */ },
>> +};
>> +MODULE_DEVICE_TABLE(of, ov2680_dt_ids);
>> +
>> +static struct i2c_driver ov2680_i2c_driver = {
>> + .driver = {
>> + .name = "ovti,ov2680",
>> + .of_match_table = ov2680_dt_ids,
>> + },
>> + .id_table = ov2680_id,
>> + .probe = ov2680_probe,
>> + .remove = ov2680_remove,
>> +};
>> +module_i2c_driver(ov2680_i2c_driver);
>> +
>> +MODULE_AUTHOR("Rui Miguel Silva <rui.silva@linaro.org>");
>> +MODULE_DESCRIPTION("OV2680 CMOS Image Sensor driver");
>> +MODULE_LICENSE("GPL v2");

\
 
 \ /
  Last update: 2018-02-23 15:56    [W:0.116 / U:0.288 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site