lkml.org 
[lkml]   [2018]   [Feb]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v1 2/2] PCI: Allow user to request power management of conventional and hotplug bridges
On Tue, Feb 20, 2018 at 10:41:33AM +0100, Rafael J. Wysocki wrote:
> On Tue, Feb 20, 2018 at 12:14 AM, Bjorn Helgaas <helgaas@kernel.org> wrote:
> > From: Bjorn Helgaas <bhelgaas@google.com>
> >
> > Previously "pcie_port_pm=force" enabled power management of PCI bridges,
> > but only for PCIe ports (not conventional PCI bridges) and only for ports
> > that do not support hotplug. Those limitations are there because we're not
> > confident that all those configurations work, not because the spec requires
> > them.
> >
> > Change "pcie_port_pm=force" to enable power management of conventional PCI
> > bridges and hotplug bridges as well as PCIe ports. As with the previous
> > PCIe port-only behavior, this is not expected to work in all systems.
> >
> > Add a "pci=bridge_pm" parameter to reflect the increased scope. For
> > backward compatibility, retain "pcie_port_pm=force" as an undocumented
> > equivalent.
> >
> > Add "pci=no_bridge_pm" as an equivalent to "pcie_port_pm=off". This
> > disables power management for all PCI bridges, which is results in the same
> > behavior as before, since we always disabled power management of
> > conventional PCI bridges, and "pcie_port_pm=off" disabled it for PCIe
> > ports.
> >
> > Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
>
> Honestly, I wouldn't do that, at least not this way.
>
> Somebody might be using pcie_port_pm=force already, for example, and
> it works for them for PCIe, but the PCI-to-PCI part of the same system
> may not.

Yes, you and Valdis are right, this is over-aggressive and I'll drop
it.

> IMO the behavior of pcie_port_pm= should be as is and I don't see
> what's wrong with it being documented.
>
> Of course, you can add pci=bridge_pm/no_bridge_pm to extend the scope,
> but for what reason really? Just to follow the letter of the spec?

Basically I was hoping to partially rectify what I think was a mistake
on my part when we merged this. 9d26d3a8f1b0 ("PCI: Put PCIe ports
into D3 during suspend") is somewhat misleading because it suggests
that PCI bridge power management can only be supported on non-hotplug
PCIe ports, when in fact this was mostly a question of testing and "we
know this works on the systems we care about so we're going to
minimize our risk by excluding others". These constraints seem pretty
Intel-centric and it's not clear how or whether they apply to other
architectures.

Adding the comments will help with that some, but in general I don't
like to artificially limit feature support because it reduces testing
exposure and makes future maintenance more difficult.

For example, we disallow D3 for hotplug bridges. I don't think the
spec requires that, so the fact that we put that limitation in
suggests that there was some issue we didn't fully understand, and now
it will be hard to go back and figure that out if and when we *do*
want to support D3 for hotplug bridges.

Anyway, I'll drop this one and just go with adding the comments.

Bjorn

\
 
 \ /
  Last update: 2018-02-20 19:17    [W:0.085 / U:1.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site