lkml.org 
[lkml]   [2018]   [Feb]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 0/6] IR support for A83T
From
Date

On 30.01.2018 18:46, Philipp Rossak wrote:
> This patch series adds support for the sunxi A83T ir module and enhances
> the sunxi-ir driver. Right now the base clock frequency for the ir driver
> is a hard coded define and is set to 8 MHz.
> This works for the most common ir receivers. On the Sinovoip Bananapi M3
> the ir receiver needs, a 3 MHz base clock frequency to work without
> problems with this driver.
>
> This patch series adds support for an optinal property that makes it able
> to override the default base clock frequency and enables the ir interface
> on the a83t and the Bananapi M3.
>
> changes since v4:
> * rename cir pin from cir_pins to r_cir_pin
> * drop unit-adress from r_cir_pin
> * add a83t compatible to the cir node
> * move muxing options to dtsi
> * rename cir label and reorder it in the bananpim3.dts file
>
> changes since v3:
> * collecting all acks & reviewd by
> * fixed typos
>
> changes since v2:
> * reorder cir pin (alphabetical)
> * fix typo in documentation
>
> changes since v1:
> * fix typos, reword Documentation
> * initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
> * change dev_info() to dev_dbg()
> * change naming to cir* in dts/dtsi
> * Added acked Ackedi-by to related patch
> * use whole memory block instead of registers needed + fix for h3/h5
>
> changes since rfc:
> * The property is now optinal. If the property is not available in
> the dtb the driver uses the default base clock frequency.
> * the driver prints out the the selected base clock frequency.
> * changed devicetree property from base-clk-frequency to clock-frequency
>
> Regards,
> Philipp
>
> Philipp Rossak (6):
> media: rc: update sunxi-ir driver to get base clock frequency from
> devicetree
> media: dt: bindings: Update binding documentation for sunxi IR
> controller
> arm: dts: sun8i: a83t: Add the cir pin for the A83T
> arm: dts: sun8i: a83t: Add support for the cir interface
> arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
> arm: dts: sun8i: h3-h5: ir register size should be the whole memory
> block
>
> Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++
> arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 5 +++++
> arch/arm/boot/dts/sun8i-a83t.dtsi | 18 ++++++++++++++++++
> arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +-
> drivers/media/rc/sunxi-cir.c | 19 +++++++++++--------
> 5 files changed, 38 insertions(+), 9 deletions(-)
>

Hey,

RC1 is now out, thus I would like to ask you to have a look at this
patch series again. Some patches still miss an acked-by. It would be
nice if we could schedule this for v4.17.

Thanks,
Philipp


\
 
 \ /
  Last update: 2018-02-12 12:01    [W:0.141 / U:0.100 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site