lkml.org 
[lkml]   [2018]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v1 01/12] dt-bindings: usb: add support for dwc3 controller on HiSilicon SoCs
From
Date
Hello!

On 03.12.2018 6:45, Yu Chen wrote:

> This patch adds binding descriptions to support the dwc3 controller
> on HiSilicon SoCs and boards like the HiKey960.
>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: John Stultz <john.stultz@linaro.org>
> Signed-off-by: Yu Chen <chenyu56@huawei.com>
> ---
> .../devicetree/bindings/usb/dwc3-hisi.txt | 67 ++++++++++++++++++++++
> 1 file changed, 67 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/dwc3-hisi.txt
>
> diff --git a/Documentation/devicetree/bindings/usb/dwc3-hisi.txt b/Documentation/devicetree/bindings/usb/dwc3-hisi.txt
> new file mode 100644
> index 000000000000..d32d2299a0a1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/dwc3-hisi.txt
> @@ -0,0 +1,67 @@
> +HiSilicon DWC3 USB SoC controller
> +
> +This file documents the parameters for the dwc3-hisi driver.
> +
> +Required properties:
> +- compatible: should be "hisilicon,hi3660-dwc3"
> +- clocks: A list of phandle + clock-specifier pairs for the
> + clocks listed in clock-names
> +- clock-names: Specify clock names
> +- resets: list of phandle and reset specifier pairs.
> +
> +Sub-nodes:
> +The dwc3 core should be added as subnode to HiSilicon DWC3 as shown in the
> +example below. The DT binding details of dwc3 can be found in:
> +Documentation/devicetree/bindings/usb/dwc3.txt
> +
> +Example:
> + usb3: hisi_dwc3 {
> + compatible = "hisilicon,hi3660-dwc3";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + clocks = <&crg_ctrl HI3660_CLK_ABB_USB>,
> + <&crg_ctrl HI3660_ACLK_GATE_USB3OTG>;
> + clock-names = "clk_usb3phy_ref", "aclk_usb3otg";
> + assigned-clocks = <&crg_ctrl HI3660_ACLK_GATE_USB3OTG>;
> + assigned-clock-rates = <229000000>;
> + resets = <&crg_rst 0x90 8>,
> + <&crg_rst 0x90 7>,
> + <&crg_rst 0x90 6>,
> + <&crg_rst 0x90 5>;
> +
> + dwc3: dwc3@ff100000 {

According to the DT spec, the node names should be generic, not chip
specific, i.e. usb@ff100000 in this case.

[...]

MBR, Sergei

\
 
 \ /
  Last update: 2018-12-03 09:36    [W:0.537 / U:0.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site