lkml.org 
[lkml]   [2018]   [Nov]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH V3 4/6] usb: ohci-platform: Add support for Broadcom STB SoC's
From
Date
On 11/7/18 10:23 AM, Alan Stern wrote:
> On Tue, 6 Nov 2018, Florian Fainelli wrote:
>
>> On 11/6/18 1:40 PM, Al Cooper wrote:
>>> On 11/6/18 11:08 AM, Alan Stern wrote:
>>>> On Mon, 5 Nov 2018, Al Cooper wrote:
>>>>
>>>>> Add support for Broadcom STB SoC's to the ohci platform driver.
>>>>>
>>>>> Signed-off-by: Al Cooper <alcooperx@gmail.com>
>>>>> ---
>>>>
>>>>> @@ -177,6 +189,8 @@ static int ohci_platform_probe(struct
>>>>> platform_device *dev)
>>>>>           ohci->flags |= OHCI_QUIRK_FRAME_NO;
>>>>>       if (pdata->num_ports)
>>>>>           ohci->num_ports = pdata->num_ports;
>>>>> +    if (pdata->suspend_without_phy_exit)
>>>>> +        hcd->suspend_without_phy_exit = 1;
>>>>
>>>> Sorry if I missed this in the earlier discussions...  Is there any
>>>> possibility of adding a DT binding that could express this requirement,
>>>> instead of putting it in the platform data?
>>>>
>>>> Alan Stern
>>>>
>>>
>>> Alan,
>>>
>>> That was my original approach but internal review suggested that I use
>>> pdata instead. Below is my original patch for:
>>
>> And the reason for that suggestion was really because it was percevied
>> as encoding a driver behavior as a Device Tree property as opposed to
>> describing something that was inherently and strictly a hardware
>> behavior (therefore suitable for Device Tree).
>
> Right. The best way to approach this problem is to identify and
> characterize the hardware behavior which makes this override necessary.
> Then _that_ can be added to DT, since it will be a property of the
> hardware rather than of the driver.
>
>>> Add the ability to skip calling the PHY's exit routine on suspend
>>> and the PHY's init routine on resume. This is to handle a USB PHY
>>> that should have it's power_off function called on suspend but cannot
>>> have it's exit function called because on exit it will disable the
>>> PHY to the point where register accesses to the Host Controllers
>>> using the PHY will be disabled and the host drivers will crash.
>
> What's special about this PHY? Why does the exit function mess the PHY
> up? Or to put it another way, why doesn't the exit function mess up
> other PHYs in the same way?
>
> For that matter, can we change the code so that suspend doesn't call
> the exit function for _any_ PHY? Will just calling the power_off
> function be good enough? If not, then why not?
>
> Alan Stern
>

In our USB hardware the USB PHY supplies a clock for the EHCI/OHCI and
XHCI host controllers and if the PHY is totally shut down the EHCI, OHCI
and XHCI registers will cause an exception if accessed and cause the
EHCI, OHCI and XHCI drivers to crash. There is always talk of fixing
this in the hardware by adding an aux clock that will takeover when the
PHY clock is shut down, but this hasn't happened yet. It seems like
"exit on suspend" still makes sense on systems that don't have this
problem (additional power savings?) so removing the exit on suspend for
all systems is not a good idea.

Al

\
 
 \ /
  Last update: 2018-11-07 16:59    [W:0.046 / U:0.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site