lkml.org 
[lkml]   [2018]   [Nov]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 06/13] dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
From
Date
Hi Rob,

On 12/11/18 11:30 PM, Rob Herring wrote:
> On Tue, Nov 06, 2018 at 02:10:58PM +0530, Lokesh Vutla wrote:
>> Add the DT binding documentation for Interrupt router driver.
>>
>> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
>> ---
>> Changes since v2:
>> - Dropped interrupt-parent from reqired properties description
>> - Updated the interrupt cells to 4.
>>
>> .../interrupt-controller/ti,sci-intr.txt | 84 +++++++++++++++++++
>> MAINTAINERS | 1 +
>> 2 files changed, 85 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>>
>> diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>> new file mode 100644
>> index 000000000000..06e69f8c812c
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>> @@ -0,0 +1,84 @@
>> +Texas Instruments K3 Interrupt Router
>> +=====================================
>> +
>> +The Interrupt Router (INTR) module provides a mechanism to mux M
>> +interrupt inputs to N interrupt outputs, where all M inputs are selectable
>> +to be driven per N output. There is one register per output (MUXCNTL_N) that
>> +controls the selection.
>> +
>> +
>> + Interrupt Router
>> + +----------------------+
>> + | Inputs Outputs |
>> + +-------+ | +------+ |
>> + | GPIO |----------->| | irq0 | | Host IRQ
>> + +-------+ | +------+ | controller
>> + | . +-----+ | +-------+
>> + +-------+ | . | 0 | |----->| IRQ |
>> + | INTA |----------->| . +-----+ | +-------+
>> + +-------+ | . . |
>> + | +------+ . |
>> + | | irqM | +-----+ |
>> + | +------+ | N | |
>> + | +-----+ |
>> + +----------------------+
>> +
>> +Configuration of these MUXCNTL_N registers is done by a system controller
>> +(like the Device Memory and Security Controller on K3 AM654 SoC). System
>> +controller will keep track of the used and unused registers within the Router.
>> +Driver should request the system controller to get the range of GIC IRQs
>> +assigned to the requesting hosts. It is the drivers responsibility to keep
>> +track of Host IRQs.
>> +
>> +Communication between the host processor running an OS and the system
>> +controller happens through a protocol called TI System Control Interface
>> +(TISCI protocol). For more details refer:
>> +Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
>> +
>> +TISCI Interrupt Router Node:
>> +----------------------------
>> +- compatible: Must be "ti,sci-intr".
>> +- interrupt-controller: Identifies the node as an interrupt controller
>> +- #interrupt-cells: Specifies the number of cells needed to encode an
>> + interrupt source. The value should be 4.
>> + First cell should contain the TISCI device ID of source
>> + Second cell should contain the interrupt source offset
>> + within the device
>> + Third cell specifies the trigger type as defined
>> + in interrupts.txt in this directory.
>> + Fourth cell should be 1 if the irq is coming from
>> + interrupt aggregator else 0.
>> +- ti,sci: Phandle to TI-SCI compatible System controller node.
>> +- ti,sci-dst-id: TISCI device ID of the destination IRQ controller.
>> +- ti,sci-rm-range-girq: TISCI subtype id representing the host irqs assigned
>> + to this interrupt router.
>
> u32 or array?

it is u32.

>
>> +
>> +For more details on TISCI IRQ resource management refer:
>> +http://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html
>> +
>> +Example:
>> +--------
>> +The following example demonstrates both interrupt router node and the consumer
>> +node(main gpio) on the AM654 SoC:
>> +
>> +main_intr: interrupt-controller@1 {
>
> Unit-address is not valid here without a reg property.

Sure will fix it in next version.

Thanks and regards,
Lokesh

>
>> + compatible = "ti,sci-intr";
>> + interrupt-controller;
>> + interrupt-parent = <&gic>;
>> + #interrupt-cells = <4>;
>> + ti,sci = <&dmsc>;
>> + ti,sci-dst-id = <56>;
>> + ti,sci-rm-range-girq = <0x1>;
>> +};
>> +
>> +main_gpio0: gpio@600000 {
>> + ...
>> + interrupt-parent = <&main_intr>;
>> + interrupts = <57 256 IRQ_TYPE_EDGE_RISING 0>,
>> + <57 257 IRQ_TYPE_EDGE_RISING 0>,
>> + <57 258 IRQ_TYPE_EDGE_RISING 0>,
>> + <57 259 IRQ_TYPE_EDGE_RISING 0>,
>> + <57 260 IRQ_TYPE_EDGE_RISING 0>,
>> + <57 261 IRQ_TYPE_EDGE_RISING 0>;
>> + ...
>> +};
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 88b28f6dec45..0e3aa3386287 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -14739,6 +14739,7 @@ F: Documentation/devicetree/bindings/reset/ti,sci-reset.txt
>> F: Documentation/devicetree/bindings/clock/ti,sci-clk.txt
>> F: drivers/clk/keystone/sci-clk.c
>> F: drivers/reset/reset-ti-sci.c
>> +F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>>
>> THANKO'S RAREMONO AM/FM/SW RADIO RECEIVER USB DRIVER
>> M: Hans Verkuil <hverkuil@xs4all.nl>
>> --
>> 2.19.1
>>
>

\
 
 \ /
  Last update: 2018-11-13 07:15    [W:0.109 / U:1.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site