lkml.org 
[lkml]   [2018]   [Oct]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/2] dt-bindings/interrupt-controller: rzn1: Add RZ/N1 gpio irq mux binding
Date
Add device binding documentation for the Renesas RZ/N1 GPIO interrupt
multiplexer.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
---
v2:
- Use interrupt-map to allow the GPIO controller info to be specified
as part of the irq.
- Don't show status in binding examples.
- Don't show the soc/board split in binding doc.
---
.../interrupt-controller/renesas,rzn1-mux.txt | 92 +++++++++++++++++++
1 file changed, 92 insertions(+)
create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt

diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt
new file mode 100644
index 000000000000..0b4ba27c00ef
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt
@@ -0,0 +1,92 @@
+* Renesas RZ/N1 GPIO Interrupt Multiplexer
+
+On Renesas RZ/N1 devices, there are several GPIO Controllers each with a number
+of interrupt outputs. All of the interrupts from the GPIO Controllers are passed
+to the GPIO Interrupt Multiplexer, which selects a sub-set of the interrupts to
+pass onto the system interrupt controller.
+
+A single node in the device tree is used to describe the GPIO IRQ Muxer.
+
+Required properties:
+- compatible: SoC-specific compatible string "renesas,<soc-specific>-gpioirqmux"
+ followed by "renesas,rzn1-gpioirqmux" as fallback. The SoC-specific compatible
+ strings must be one of:
+ "renesas,r9a06g032-gpioirqmux" for RZ/N1D
+ "renesas,r9a06g033-gpioirqmux" for RZ/N1S
+- interrupt-controller: Identifies the node as an interrupt controller.
+- #interrupt-cells: should be <1>. The meaning of the cells is the input
+ interrupt index, 0 to 95.
+- reg: Base address and size of GPIO IRQ Muxer registers.
+- interrupts: This is a list of interrupt specifiers. Each interrupt consists of
+ three numbers that represent:
+ - (a) the index of the GPIO Interrupt Multiplexer output interrupt (0..7)
+ - (b) the index of the GPIO Controller input interrupt (0..2)
+ - (c) the interrupt index of the GPIO Controller input interrupt (0..31).
+- interrupt-parent: A phandle for a local node that specifies an interrupt-map.
+ The interrupt-map node must specify #interrupt-cells = <3>, and an
+ interrupt-map property. The interrupt-map is used to translate the interrupt
+ specifier to the output interrupts. It is used in conjunction with an
+ interrupt-map-mask property to mask (b) and (c) from the interrupt specifier
+ so that essentially there is a direct map from (a) to the output interrupt.
+ Therefore (b) and (c) can be used to determine the interrupt source and
+ configure the hardware accordingly. For information on interrupts,
+ see Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+Example:
+
+ The following is an example for the RZ/N1D SoC.
+
+ gpioirqmux: gpioirqmux@51000480 {
+ compatible = "renesas,r9a06g032-gpioirqmux",
+ "renesas,rzn1-gpioirqmux";
+ reg = <0x51000480 0x20>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gpioirqmux_map>;
+ interrupts =
+ <0 1 17>, /* gpio1a 17 */
+ <1 1 24>, /* gpio1a 24 */
+ <2 1 26>; /* gpio1a 26 */
+
+ gpioirqmux_map: gpioirqmux-map {
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-map-mask = <7 0 0>;
+ interrupt-map =
+ <0 0 0 &gic GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <1 0 0 &gic GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <2 0 0 &gic GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <3 0 0 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <4 0 0 &gic GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+ <5 0 0 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <6 0 0 &gic GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <7 0 0 &gic GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ gpio1: gpio@5000c000 {
+ compatible = "snps,dw-apb-gpio";
+ reg = <0x5000c000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "bus";
+ clocks = <&sysctrl R9A06G032_HCLK_GPIO1>;
+
+ gpio1a: gpio-controller@0 {
+ compatible = "snps,dw-apb-gpio-port";
+ bank-name = "gpio1a";
+ gpio-controller;
+ #gpio-cells = <2>;
+ snps,nr-gpios = <32>;
+ reg = <0>;
+
+ interrupt-controller;
+ interrupt-parent = <&gpioirqmux>;
+ interrupts = < 0 1 2 3 4 5 6 7
+ 8 9 10 11 12 13 14 15
+ 16 17 18 19 20 21 22 23
+ 24 25 26 27 28 29 30 31 >;
+ #interrupt-cells = <2>;
+ };
+ };
--
2.17.1
\
 
 \ /
  Last update: 2018-10-30 11:45    [W:0.078 / U:0.192 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site