lkml.org 
[lkml]   [2018]   [Oct]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/5] dt-bindings: phy-qcom-qmp: Fix register underspecification
On Thu, Oct 18, 2018 at 02:09:29PM -0700, Evan Green wrote:
> This change adds register regions for the second lane of dual-lane nodes.
> This additional specification is needed so that the driver can stop
> reaching beyond the tx and rx register allocations to get at the
> second lane registers in a dual-lane PHY.
>
> While in there, document #clock-cells as optional for PHYs that don't
> provide a pipe clock. Also, document the pcs_misc register region, which
> was being quietly supplied and used.
>
> Signed-off-by: Evan Green <evgreen@chromium.org>
>
> ---
> This applies atop linux-next 20181018 with the addition of Doug's
> changes [1] and [2].
>
> [1] https://lore.kernel.org/lkml/20181012213632.252346-1-dianders@chromium.org/
> [2] https://lore.kernel.org/lkml/20181012213926.253765-1-dianders@chromium.org/
>
> .../devicetree/bindings/phy/qcom-qmp-phy.txt | 73 +++++++++++++++++++---
> 1 file changed, 65 insertions(+), 8 deletions(-)

One nit below, otherwise:

Reviewed-by: Rob Herring <robh@kernel.org>

>
> diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> index fbc198d5dd39..297a7c753fc8 100644
> --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> @@ -25,7 +25,7 @@ Required properties:
> - For all others:
> - The reg-names property shouldn't be defined.
>
> - - #clock-cells: must be 1
> + - #clock-cells: must be 1 (PCIe and USB3 PHYs only)
> - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
> interface (for pipe based PHYs). These clock are then gate-controlled
> by gcc.
> @@ -82,23 +82,26 @@ Required nodes:
> - Each device node of QMP phy is required to have as many child nodes as
> the number of lanes the PHY has.
>
> -Required properties for child node:
> +Required properties for child nodes of PCIe PHYs (one child per lane):
> - reg: list of offset and length pairs of register sets for PHY blocks -
> - - index 0: tx
> - - index 1: rx
> - - index 2: pcs
> - - index 3: pcs_misc (optional)
> + tx, rx, pcs, and pcs_misc (optional).
> + - #phy-cells: must be 0
>
> +Required properties for a single "lanes" child node of non-PCIe PHYs:
> + - reg: list of offset and length pairs of register sets for PHY blocks
> + For 1-lane devices:
> + tx, rx, pcs, and (optionally) pcs_misc
> + For 2-lane devices:
> + tx0, rx0, pcs, tx1, rx1, and (optionally) pcs_misc
> - #phy-cells: must be 0
>
> -Required properties child node of pcie and usb3 qmp phys:
> +Required properties for child node of PCIe and USB3 qmp phys:
> - clocks: a list of phandles and clock-specifier pairs,
> one for each entry in clock-names.
> - clock-names: Must contain following:
> "pipe<lane-number>" for pipe clock specific to each lane.
> - clock-output-names: Name of the PHY clock that will be the parent for
> the above pipe clock.
> -
> For "qcom,ipq8074-qmp-pcie-phy":
> - "pcie20_phy0_pipe_clk" Pipe Clock parent
> (or)
> @@ -150,3 +153,57 @@ Example:
> ...
> ...
> };
> +
> + phy@88eb000 {
> + compatible = "qcom,sdm845-qmp-usb3-uni-phy";
> + reg = <0x88eb000 0x18c>;
> + status = "disabled";

Don't show status in examples.

> + #clock-cells = <1>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
> + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> + <&gcc GCC_USB3_SEC_CLKREF_CLK>,
> + <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
> + clock-names = "aux", "cfg_ahb", "ref", "com_aux";
> +
> + resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
> + <&gcc GCC_USB3_PHY_SEC_BCR>;
> + reset-names = "phy", "common";
> +
> + lane@88eb200 {
> + reg = <0x88eb200 0x128>,
> + <0x88eb400 0x1fc>,
> + <0x88eb800 0x218>,
> + <0x88e9600 0x70>;
> + #phy-cells = <0>;
> + clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "usb3_uni_phy_pipe_clk_src";
> + };
> + };
> +
> + phy@1d87000 {
> + compatible = "qcom,sdm845-qmp-ufs-phy";
> + reg = <0x1d87000 0x18c>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + clock-names = "ref",
> + "ref_aux";
> + clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
> + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
> +
> + status = "disabled";
> +
> + lanes@1d87400 {
> + reg = <0x1d87400 0x108>,
> + <0x1d87600 0x1e0>,
> + <0x1d87c00 0x1dc>,
> + <0x1d87800 0x108>,
> + <0x1d87a00 0x1e0>;
> + #phy-cells = <0>;
> + };
> + };
> --
> 2.16.4
>

\
 
 \ /
  Last update: 2018-10-23 02:30    [W:1.415 / U:0.580 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site