lkml.org 
[lkml]   [2018]   [Jan]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 3/3] usb: host: Implement workaround for Erratum A-009668
From
Date
On 19.12.2017 12:16, yinbo.zhu@nxp.com wrote:
> From: yinbo.zhu <yinbo.zhu@nxp.com>
>
> This issue is observed in USB 2.0 mode when the USB 3.0 host
> controller is connected to a FS/LS device via a hub. The
> host controller issues start-split (SSPLIT) and (CSPLIT)
> tokens to accomplish a split-transaction. A
> split-transaction consists of a SSPLIT token, token/data
> consists of a SSPLIT token, token/data packets, CSPLIT token
> and token/data/handshake packets. A SSPLIT token is issued
> by the host controller to the hub followed by token/data/
> handshake packets. The hub then relays the token/data/
> handshake packets to the FS /LS device. Sometime later, the
> host controller issues a CSPLIT token followed by the same
> token/data/handshake packets to the hub to complete the
> split-transaction. As an example scenario, when the xHCI
> driver issues an Address device command with BSR=0, the
> host controller sends SETUP(SET_ADDRESS) tokens on the USB
> as part of splittransactions. If the host controller
> receives a NYET response from the hub for the CSPLIT SETUP,
> it means that the split-transaction has not yet been
> completed or the hub is not able to handle the split
> transaction. In such a case, the host controller keeps
> retrying the splittransactions until such time an ACK
> response is received from the hub for the CSPLIT SETUP token
> . If the split-transactions do not complete in a time bound
> manner, the xHCI driver may issue a Stop Endpoint Command.
> The host controller does not service the Stop Endpoint
> Command and eventually the xHCI driver times out waiting for
> the Stop Endpoint Command to complete.
>
> Impact: Stop Endpoint Command does not complete.
> Workaround: Instead of issuing a Stop Endpoint Command,
> issue a Disable Slot Command with the corresponding slot
> ID. Alternately, you can issue an Address Device Command
> with BSR=1.
>
> Configs Affected:
> LS1012A-R1.0, LS1012A-R2.0, LS1021-20-22A-R1.0,
> LS1021-20-22A-R2.0, LS1043-23A-R1.0, LS1043-23A-R1.1,
> LS1046-26A-R1.0, LS1088-48A-R1.0, LS2080-40A-R1.0,
> LS2081A-R1.1, LS2085-45A-R1.0, LS2088-48A-R1.0,
> LS2088-48A-R1.1, LX2160-2120-2080A-R1.0.
>
> Signed-off-by: yinbo zhu <yinbo.zhu@nxp.com>
> ---
> Change in v4:
> Remove the point in "yinbo.zhu"

> diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
> index 5141856..20c9af4 100644
> --- a/drivers/usb/host/xhci.c
> +++ b/drivers/usb/host/xhci.c
> @@ -1521,6 +1521,18 @@ static int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
> xhci_ring_cmd_db(xhci);
> }
>
> + /*
> + *erratum A-009668: Stop Endpoint Command does not complete.
> + *Workaround: Instead of issuing a Stop Endpoint Command,
> + *issue a Disable Slot Command with the corresponding slot ID.
> + *Alternately, you can issue an Address Device Command with
> + *BSR=1
> + */
> + if ((urb->dev->speed <= USB_SPEED_HIGH) &&
> + (xhci->quirks & XHCI_STOP_EP_IN_U1)) {
> + xhci_queue_slot_control(xhci, command, TRB_DISABLE_SLOT,
> + urb->dev->slot_id);
> + }

Address device in xHCI is done with a address device command on the command ring,
if it times out then xhci_handle_command_timeout() will be called. No stop endpoint command
should be involved (if I remember correctly)

xhci_urb_dequeue() may be called in other cases for LS/FS URBs that timed out,
due to your split transaction hang errata, but a disable slot command can't just be bluntly
issued before first properly stopping all slot endpoints, and giving back all the other pending URBs

-Mathias

\
 
 \ /
  Last update: 2018-01-04 15:55    [W:0.159 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site