lkml.org 
[lkml]   [2017]   [Sep]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH v5 2/2] thermal: add brcmstb AVS TMON driver
From
Date


On 17-09-26 02:38 PM, Markus Mayer wrote:
> On 26 September 2017 at 14:32, Scott Branden <scott.branden@broadcom.com> wrote:
>> Hi Markus,
>>
>>
>> On 17-09-26 02:27 PM, Markus Mayer wrote:
>>> From: Brian Norris <computersforpeace@gmail.com>
>>>
>>> The AVS TMON core provides temperature readings, a pair of configurable
>>> high- and low-temperature threshold interrupts, and an emergency
>>> over-temperature chip reset. The driver utilizes the first two to
>>> provide temperature readings and high-temperature notifications to
>>> applications. The over-temperature reset is not exposed to
>>> applications; this reset threshold is critical to the system and should
>>> be set with care within the bootloader.
>>>
>>> Applications may choose to utilize the notification mechanism, the
>>> temperature reading mechanism (e.g., through polling), or both.
>>>
>>> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
>>> Signed-off-by: Doug Berger <opendmb@gmail.com>
>>> Signed-off-by: Markus Mayer <mmayer@broadcom.com>
>>> ---
>>> drivers/thermal/Kconfig | 2 +-
>>> drivers/thermal/broadcom/Kconfig | 7 +
>>> drivers/thermal/broadcom/Makefile | 1 +
>>> drivers/thermal/broadcom/brcmstb_thermal.c | 387
>>> +++++++++++++++++++++++++++++
>>> 4 files changed, 396 insertions(+), 1 deletion(-)
>>> create mode 100644 drivers/thermal/broadcom/brcmstb_thermal.c
>>>
>>> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
>>> index 07002df..96774a7 100644
>>> --- a/drivers/thermal/Kconfig
>>> +++ b/drivers/thermal/Kconfig
>>> @@ -408,7 +408,7 @@ config MTK_THERMAL
>>> controller present in Mediatek SoCs
>>> menu "Broadcom thermal drivers"
>>> -depends on ARCH_BCM || COMPILE_TEST
>>> +depends on ARCH_BCM || ARCH_BRCMSTB || COMPILE_TEST
>> No need for this additional depends. ARCH_BCM is always defined before
>> ARCH_BRCMSTB can be selected.
> ARCH_BCM does not exist in arch/arm64/configs/defconfig. ARCH_BRCMSTB
> does. So, we do need both or the driver won't be built on ARM64.
> (After internal discussions we went with that approach rather than
> defining ARCH_BCM on ARM64.)
Got it. Looking at our internal iproc tree I see we've done exactly the
same with ARCH_BCM_IPROC needing to be added. We haven't upstreamed
the thermal driver needing it yet.

Perhaps we should add ARCH_BCM to ARM64....

>
>>> source "drivers/thermal/broadcom/Kconfig"
>>> endmenu
>>> diff --git a/drivers/thermal/broadcom/Kconfig
>>> b/drivers/thermal/broadcom/Kconfig
>>> index 42c098e..c106a15 100644
>>> --- a/drivers/thermal/broadcom/Kconfig
>>> +++ b/drivers/thermal/broadcom/Kconfig
>>> @@ -6,6 +6,13 @@ config BCM2835_THERMAL
>>> help
>>> Support for thermal sensors on Broadcom bcm2835 SoCs.
>>> +config BRCMSTB_THERMAL
>>> + tristate "Broadcom STB AVS TMON thermal driver"
>>> + depends on ARCH_BRCMSTB || COMPILE_TEST
>>> + help
>>> + Enable this driver if you have a Broadcom STB SoC and would like
>>> + thermal framework support.
>>> +
>>> config BCM_NS_THERMAL
>>> tristate "Northstar thermal driver"
>>> depends on ARCH_BCM_IPROC || COMPILE_TEST
>>> diff --git a/drivers/thermal/broadcom/Makefile
>>> b/drivers/thermal/broadcom/Makefile
>>> index c6f62e4..fae10ec 100644
>>> --- a/drivers/thermal/broadcom/Makefile
>>> +++ b/drivers/thermal/broadcom/Makefile
>>> @@ -1,2 +1,3 @@
>>> obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
>>> +obj-$(CONFIG_BRCMSTB_THERMAL) += brcmstb_thermal.o
>>> obj-$(CONFIG_BCM_NS_THERMAL) += ns-thermal.o
>>> diff --git a/drivers/thermal/broadcom/brcmstb_thermal.c
>>> b/drivers/thermal/broadcom/brcmstb_thermal.c
>>> new file mode 100644
>>> index 0000000..1919f91
>>> --- /dev/null
>>> +++ b/drivers/thermal/broadcom/brcmstb_thermal.c
>>> @@ -0,0 +1,387 @@
>>> +/*
>>> + * Broadcom STB AVS TMON thermal sensor driver
>>> + *
>>> + * Copyright (c) 2015-2017 Broadcom
>>> + *
>>> + * This software is licensed under the terms of the GNU General Public
>>> + * License version 2, as published by the Free Software Foundation, and
>>> + * may be copied, distributed, and modified under those terms.
>>> + *
>>> + * This program is distributed in the hope that it will be useful,
>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>>> + * GNU General Public License for more details.
>>> + *
>>> + */
>>> +
>>> +#define DRV_NAME "brcmstb_thermal"
>>> +
>>> +#define pr_fmt(fmt) DRV_NAME ": " fmt
>>> +
>>> +#include <linux/bitops.h>
>>> +#include <linux/device.h>
>>> +#include <linux/err.h>
>>> +#include <linux/io.h>
>>> +#include <linux/irqreturn.h>
>>> +#include <linux/interrupt.h>
>>> +#include <linux/kernel.h>
>>> +#include <linux/module.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/thermal.h>
>>> +
>>> +#define AVS_TMON_STATUS 0x00
>>> + #define AVS_TMON_STATUS_valid_msk BIT(11)
>>> + #define AVS_TMON_STATUS_data_msk GENMASK(10, 1)
>>> + #define AVS_TMON_STATUS_data_shift 1
>>> +
>>> +#define AVS_TMON_EN_OVERTEMP_RESET 0x04
>>> + #define AVS_TMON_EN_OVERTEMP_RESET_msk BIT(0)
>>> +
>>> +#define AVS_TMON_RESET_THRESH 0x08
>>> + #define AVS_TMON_RESET_THRESH_msk GENMASK(10, 1)
>>> + #define AVS_TMON_RESET_THRESH_shift 1
>>> +
>>> +#define AVS_TMON_INT_IDLE_TIME 0x10
>>> +
>>> +#define AVS_TMON_EN_TEMP_INT_SRCS 0x14
>>> + #define AVS_TMON_EN_TEMP_INT_SRCS_high BIT(1)
>>> + #define AVS_TMON_EN_TEMP_INT_SRCS_low BIT(0)
>>> +
>>> +#define AVS_TMON_INT_THRESH 0x18
>>> + #define AVS_TMON_INT_THRESH_high_msk GENMASK(26, 17)
>>> + #define AVS_TMON_INT_THRESH_high_shift 17
>>> + #define AVS_TMON_INT_THRESH_low_msk GENMASK(10, 1)
>>> + #define AVS_TMON_INT_THRESH_low_shift 1
>>> +
>>> +#define AVS_TMON_TEMP_INT_CODE 0x1c
>>> +#define AVS_TMON_TP_TEST_ENABLE 0x20
>>> +
>>> +/* Default coefficients */
>>> +#define AVS_TMON_TEMP_SLOPE -487
>>> +#define AVS_TMON_TEMP_OFFSET 410040
>>> +
>>> +/* HW related temperature constants */
>>> +#define AVS_TMON_TEMP_MAX 0x3ff
>>> +#define AVS_TMON_TEMP_MIN -88161
>>> +#define AVS_TMON_TEMP_MASK AVS_TMON_TEMP_MAX
>>> +
>>> +enum avs_tmon_trip_type {
>>> + TMON_TRIP_TYPE_LOW = 0,
>>> + TMON_TRIP_TYPE_HIGH,
>>> + TMON_TRIP_TYPE_RESET,
>>> + TMON_TRIP_TYPE_MAX,
>>> +};
>>> +
>>> +struct avs_tmon_trip {
>>> + /* HW bit to enable the trip */
>>> + u32 enable_offs;
>>> + u32 enable_mask;
>>> +
>>> + /* HW field to read the trip temperature */
>>> + u32 reg_offs;
>>> + u32 reg_msk;
>>> + int reg_shift;
>>> +};
>>> +
>>> +static struct avs_tmon_trip avs_tmon_trips[] = {
>>> + /* Trips when temperature is below threshold */
>>> + [TMON_TRIP_TYPE_LOW] = {
>>> + .enable_offs = AVS_TMON_EN_TEMP_INT_SRCS,
>>> + .enable_mask = AVS_TMON_EN_TEMP_INT_SRCS_low,
>>> + .reg_offs = AVS_TMON_INT_THRESH,
>>> + .reg_msk = AVS_TMON_INT_THRESH_low_msk,
>>> + .reg_shift = AVS_TMON_INT_THRESH_low_shift,
>>> + },
>>> + /* Trips when temperature is above threshold */
>>> + [TMON_TRIP_TYPE_HIGH] = {
>>> + .enable_offs = AVS_TMON_EN_TEMP_INT_SRCS,
>>> + .enable_mask = AVS_TMON_EN_TEMP_INT_SRCS_high,
>>> + .reg_offs = AVS_TMON_INT_THRESH,
>>> + .reg_msk = AVS_TMON_INT_THRESH_high_msk,
>>> + .reg_shift = AVS_TMON_INT_THRESH_high_shift,
>>> + },
>>> + /* Automatically resets chip when above threshold */
>>> + [TMON_TRIP_TYPE_RESET] = {
>>> + .enable_offs = AVS_TMON_EN_OVERTEMP_RESET,
>>> + .enable_mask = AVS_TMON_EN_OVERTEMP_RESET_msk,
>>> + .reg_offs = AVS_TMON_RESET_THRESH,
>>> + .reg_msk = AVS_TMON_RESET_THRESH_msk,
>>> + .reg_shift = AVS_TMON_RESET_THRESH_shift,
>>> + },
>>> +};
>>> +
>>> +struct brcmstb_thermal_priv {
>>> + void __iomem *tmon_base;
>>> + struct device *dev;
>>> + struct thermal_zone_device *thermal;
>>> +};
>>> +
>>> +static void avs_tmon_get_coeffs(struct thermal_zone_device *tz, int
>>> *slope,
>>> + int *offset)
>>> +{
>>> + *slope = thermal_zone_get_slope(tz);
>>> + *offset = thermal_zone_get_offset(tz);
>>> +}
>>> +
>>> +/* Convert a HW code to a temperature reading (millidegree celsius) */
>>> +static inline int avs_tmon_code_to_temp(struct thermal_zone_device *tz,
>>> + u32 code)
>>> +{
>>> + const int val = code & AVS_TMON_TEMP_MASK;
>>> + int slope, offset;
>>> +
>>> + avs_tmon_get_coeffs(tz, &slope, &offset);
>>> +
>>> + return slope * val + offset;
>>> +}
>>> +
>>> +/*
>>> + * Convert a temperature value (millidegree celsius) to a HW code
>>> + *
>>> + * @temp: temperature to convert
>>> + * @low: if true, round toward the low side
>>> + */
>>> +static inline u32 avs_tmon_temp_to_code(struct thermal_zone_device *tz,
>>> + int temp, bool low)
>>> +{
>>> + int slope, offset;
>>> +
>>> + if (temp < AVS_TMON_TEMP_MIN)
>>> + return AVS_TMON_TEMP_MAX; /* Maximum code value */
>>> +
>>> + avs_tmon_get_coeffs(tz, &slope, &offset);
>>> +
>>> + if (temp >= offset)
>>> + return 0; /* Minimum code value */
>>> +
>>> + if (low)
>>> + return (u32)(DIV_ROUND_UP(offset - temp, abs(slope)));
>>> + else
>>> + return (u32)((offset - temp) / abs(slope));
>>> +}
>>> +
>>> +static int brcmstb_get_temp(void *data, int *temp)
>>> +{
>>> + struct brcmstb_thermal_priv *priv = data;
>>> + u32 val;
>>> + long t;
>>> +
>>> + val = __raw_readl(priv->tmon_base + AVS_TMON_STATUS);
>>> +
>>> + if (!(val & AVS_TMON_STATUS_valid_msk)) {
>>> + dev_err(priv->dev, "reading not valid\n");
>>> + return -EIO;
>>> + }
>>> +
>>> + val = (val & AVS_TMON_STATUS_data_msk) >>
>>> AVS_TMON_STATUS_data_shift;
>>> +
>>> + t = avs_tmon_code_to_temp(priv->thermal, val);
>>> + if (t < 0)
>>> + *temp = 0;
>>> + else
>>> + *temp = t;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static void avs_tmon_trip_enable(struct brcmstb_thermal_priv *priv,
>>> + enum avs_tmon_trip_type type, int en)
>>> +{
>>> + struct avs_tmon_trip *trip = &avs_tmon_trips[type];
>>> + u32 val = __raw_readl(priv->tmon_base + trip->enable_offs);
>>> +
>>> + dev_dbg(priv->dev, "%sable trip, type %d\n", en ? "en" : "dis",
>>> type);
>>> +
>>> + if (en)
>>> + val |= trip->enable_mask;
>>> + else
>>> + val &= ~trip->enable_mask;
>>> +
>>> + __raw_writel(val, priv->tmon_base + trip->enable_offs);
>>> +}
>>> +
>>> +static int avs_tmon_get_trip_temp(struct brcmstb_thermal_priv *priv,
>>> + enum avs_tmon_trip_type type)
>>> +{
>>> + struct avs_tmon_trip *trip = &avs_tmon_trips[type];
>>> + u32 val = __raw_readl(priv->tmon_base + trip->reg_offs);
>>> +
>>> + val &= trip->reg_msk;
>>> + val >>= trip->reg_shift;
>>> +
>>> + return avs_tmon_code_to_temp(priv->thermal, val);
>>> +}
>>> +
>>> +static void avs_tmon_set_trip_temp(struct brcmstb_thermal_priv *priv,
>>> + enum avs_tmon_trip_type type,
>>> + int temp)
>>> +{
>>> + struct avs_tmon_trip *trip = &avs_tmon_trips[type];
>>> + u32 val, orig;
>>> +
>>> + dev_dbg(priv->dev, "set temp %d to %d\n", type, temp);
>>> +
>>> + /* round toward low temp for the low interrupt */
>>> + val = avs_tmon_temp_to_code(priv->thermal, temp,
>>> + type == TMON_TRIP_TYPE_LOW);
>>> +
>>> + val <<= trip->reg_shift;
>>> + val &= trip->reg_msk;
>>> +
>>> + orig = __raw_readl(priv->tmon_base + trip->reg_offs);
>>> + orig &= ~trip->reg_msk;
>>> + orig |= val;
>>> + __raw_writel(orig, priv->tmon_base + trip->reg_offs);
>>> +}
>>> +
>>> +static int avs_tmon_get_intr_temp(struct brcmstb_thermal_priv *priv)
>>> +{
>>> + u32 val;
>>> +
>>> + val = __raw_readl(priv->tmon_base + AVS_TMON_TEMP_INT_CODE);
>>> + return avs_tmon_code_to_temp(priv->thermal, val);
>>> +}
>>> +
>>> +static irqreturn_t brcmstb_tmon_irq_thread(int irq, void *data)
>>> +{
>>> + struct brcmstb_thermal_priv *priv = data;
>>> + int low, high, intr;
>>> +
>>> + low = avs_tmon_get_trip_temp(priv, TMON_TRIP_TYPE_LOW);
>>> + high = avs_tmon_get_trip_temp(priv, TMON_TRIP_TYPE_HIGH);
>>> + intr = avs_tmon_get_intr_temp(priv);
>>> +
>>> + dev_dbg(priv->dev, "low/intr/high: %d/%d/%d\n",
>>> + low, intr, high);
>>> +
>>> + /* Disable high-temp until next threshold shift */
>>> + if (intr >= high)
>>> + avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 0);
>>> + /* Disable low-temp until next threshold shift */
>>> + if (intr <= low)
>>> + avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 0);
>>> +
>>> + /*
>>> + * Notify using the interrupt temperature, in case the temperature
>>> + * changes before it can next be read out
>>> + */
>>> + thermal_zone_device_update(priv->thermal, intr);
>>> +
>>> + return IRQ_HANDLED;
>>> +}
>>> +
>>> +static int brcmstb_set_trips(void *data, int low, int high)
>>> +{
>>> + struct brcmstb_thermal_priv *priv = data;
>>> +
>>> + dev_dbg(priv->dev, "set trips %d <--> %d\n", low, high);
>>> +
>>> + /*
>>> + * Disable low-temp if "low" is too small. As per thermal
>>> framework
>>> + * API, we use -INT_MAX rather than INT_MIN.
>>> + */
>>> + if (low <= -INT_MAX) {
>>> + avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 0);
>>> + } else {
>>> + avs_tmon_set_trip_temp(priv, TMON_TRIP_TYPE_LOW, low);
>>> + avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 1);
>>> + }
>>> +
>>> + /* Disable high-temp if "high" is too big. */
>>> + if (high == INT_MAX) {
>>> + avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 0);
>>> + } else {
>>> + avs_tmon_set_trip_temp(priv, TMON_TRIP_TYPE_HIGH, high);
>>> + avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 1);
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct thermal_zone_of_device_ops of_ops = {
>>> + .get_temp = brcmstb_get_temp,
>>> + .set_trips = brcmstb_set_trips,
>>> +};
>>> +
>>> +static const struct of_device_id brcmstb_thermal_id_table[] = {
>>> + { .compatible = "brcm,avs-tmon" },
>>> + {},
>>> +};
>>> +MODULE_DEVICE_TABLE(of, brcmstb_thermal_id_table);
>>> +
>>> +static int brcmstb_thermal_probe(struct platform_device *pdev)
>>> +{
>>> + struct thermal_zone_device *thermal;
>>> + struct brcmstb_thermal_priv *priv;
>>> + struct resource *res;
>>> + int irq, ret;
>>> +
>>> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
>>> + if (!priv)
>>> + return -ENOMEM;
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> + priv->tmon_base = devm_ioremap_resource(&pdev->dev, res);
>>> + if (IS_ERR(priv->tmon_base))
>>> + return PTR_ERR(priv->tmon_base);
>>> +
>>> + priv->dev = &pdev->dev;
>>> + platform_set_drvdata(pdev, priv);
>>> +
>>> + thermal = thermal_zone_of_sensor_register(&pdev->dev, 0, priv,
>>> &of_ops);
>>> + if (IS_ERR(thermal)) {
>>> + ret = PTR_ERR(thermal);
>>> + dev_err(&pdev->dev, "could not register sensor: %d\n",
>>> ret);
>>> + return ret;
>>> + }
>>> +
>>> + priv->thermal = thermal;
>>> +
>>> + irq = platform_get_irq(pdev, 0);
>>> + if (irq < 0) {
>>> + dev_err(&pdev->dev, "could not get IRQ\n");
>>> + ret = irq;
>>> + goto err;
>>> + }
>>> + ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
>>> + brcmstb_tmon_irq_thread,
>>> IRQF_ONESHOT,
>>> + DRV_NAME, priv);
>>> + if (ret < 0) {
>>> + dev_err(&pdev->dev, "could not request IRQ: %d\n", ret);
>>> + goto err;
>>> + }
>>> +
>>> + dev_info(&pdev->dev, "registered AVS TMON of-sensor driver\n");
>>> +
>>> + return 0;
>>> +
>>> +err:
>>> + thermal_zone_of_sensor_unregister(&pdev->dev, thermal);
>>> + return ret;
>>> +}
>>> +
>>> +static int brcmstb_thermal_exit(struct platform_device *pdev)
>>> +{
>>> + struct brcmstb_thermal_priv *priv = platform_get_drvdata(pdev);
>>> + struct thermal_zone_device *thermal = priv->thermal;
>>> +
>>> + if (thermal)
>>> + thermal_zone_of_sensor_unregister(&pdev->dev,
>>> priv->thermal);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct platform_driver brcmstb_thermal_driver = {
>>> + .probe = brcmstb_thermal_probe,
>>> + .remove = brcmstb_thermal_exit,
>>> + .driver = {
>>> + .name = DRV_NAME,
>>> + .of_match_table = brcmstb_thermal_id_table,
>>> + },
>>> +};
>>> +module_platform_driver(brcmstb_thermal_driver);
>>> +
>>> +MODULE_LICENSE("GPL v2");
>>> +MODULE_AUTHOR("Brian Norris");
>>> +MODULE_DESCRIPTION("Broadcom STB AVS TMON thermal driver");
>>

\
 
 \ /
  Last update: 2017-09-27 00:08    [W:7.728 / U:0.376 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site