lkml.org 
[lkml]   [2017]   [Aug]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 3/6] dt-bindings: add binding for Sitronix ST7586 display panels
From
Date
On 08/04/2017 04:48 AM, Noralf Trønnes wrote:
>
> Den 04.08.2017 00.33, skrev David Lechner:
>> This adds a new binding for Sitronix ST7586 display panels.
>>
>> Using lego as the vendor prefix in the compatible string because the
>> display
>> panel I am working with is an integral part of the LEGO MINDSTORMS EV3.
>
> Is this display available outside of this Lego part?
No, it is not.

> If not you can remove the properties you don't need for this particular
> display setup. Another st7586 display with a different panel would need
> a different initialization sequence and compatible string, so we can
> add properties when/if that happens.

OK. so I will drop power-supply and backlight.

Should I remove these from the driver as well? There are some panels out
there that could use them.[1]

[1]:
http://www.buydisplay.com/download/manual/ERC240160-1_Series_Datasheet.pdf

>
> Noralf.
>
>> Signed-off-by: David Lechner <david@lechnology.com>
>> ---
>> .../bindings/display/sitronix,st7586.txt | 26
>> ++++++++++++++++++++++
>> 1 file changed, 26 insertions(+)
>> create mode 100644
>> Documentation/devicetree/bindings/display/sitronix,st7586.txt
>>
>> diff --git
>> a/Documentation/devicetree/bindings/display/sitronix,st7586.txt
>> b/Documentation/devicetree/bindings/display/sitronix,st7586.txt
>> new file mode 100644
>> index 0000000..dfb0b7b
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/display/sitronix,st7586.txt
>> @@ -0,0 +1,26 @@
>> +Sitronix ST7586 display panel
>> +
>> +Required properties:
>> +- compatible: "lego,ev3-lcd".
>> +
>> +The node for this driver must be a child node of a SPI controller, hence
>> +all mandatory properties described in ../spi/spi-bus.txt must be
>> specified.
>> +
>> +Optional properties:
>> +- dc-gpios: D/C pin. The presence/absence of this GPIO determines
>> + the panel interface operation mode (IF[3:1] pins):
>> + - present: IF=011 4-wire 8-bit data serial interface
>> + - absent: IF=010 3-wire 9-bit data serial interface
>> +- reset-gpios: Reset pin
>> +- power-supply: A regulator node for the supply voltage.
>> +- backlight: phandle of the backlight device attached to the panel
>> +- rotation: panel rotation in degrees counter clockwise
>> (0,90,180,270)
>> +
>> +Example:
>> + display@0{
>> + compatible = "lego,ev3-lcd";
>> + reg = <0>;
>> + spi-max-frequency = <10000000>;
>> + dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
>> + reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>;
>> + };
>

\
 
 \ /
  Last update: 2017-08-04 18:52    [W:0.107 / U:0.636 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site