lkml.org 
[lkml]   [2017]   [Aug]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 1/2] arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2
From
Date


On 08/04/2017 02:19 PM, Matthias Brugger wrote:
>
>
> On 08/04/2017 12:14 PM, Sean Wang wrote:
>> On Fri, 2017-08-04 at 11:59 +0800, sean.wang@mediatek.com wrote:
>>> From: Sean Wang <sean.wang@mediatek.com>
>>>
>>> The bananapi-r2 board has an SD-card controller and built-in
>>> EMMC storage so enables those devices in the devicetree. Also
>>> cleanup nodes in alphabetical order in the patch.
>>>
>>
>> Hi, Matthias
>>
>> could your help remove those words "Also cleanup nodes in alphabetical
>> order in the patch." when merging, i was forgetting to do it.
>>
>> or prefer wanting me to resend it again?
>
> Yes I can do that. No need to resend.
>

Both patches pushed to v4.13-next/dts32 now

Thanks a lot,
Matthias

> Regards,
> Matthias
>
>>
>> Sean
>>
>>> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
>>> Signed-off-by: Sean Wang <sean.wang@mediatek.com>
>>> ---
>>> arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts | 37 +++++++++++++++++++++++++++
>>> 1 file changed, 37 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>>> b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>>> index 9f3e6dd..444ed93 100644
>>> --- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>>> +++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>>> @@ -179,6 +179,32 @@
>>> status = "okay";
>>> };
>>> +&mmc0 {
>>> + pinctrl-names = "default", "state_uhs";
>>> + pinctrl-0 = <&mmc0_pins_default>;
>>> + pinctrl-1 = <&mmc0_pins_uhs>;
>>> + status = "okay";
>>> + bus-width = <8>;
>>> + max-frequency = <50000000>;
>>> + cap-mmc-highspeed;
>>> + vmmc-supply = <&mt6323_vemc3v3_reg>;
>>> + vqmmc-supply = <&mt6323_vio18_reg>;
>>> + non-removable;
>>> +};
>>> +
>>> +&mmc1 {
>>> + pinctrl-names = "default", "state_uhs";
>>> + pinctrl-0 = <&mmc1_pins_default>;
>>> + pinctrl-1 = <&mmc1_pins_uhs>;
>>> + status = "okay";
>>> + bus-width = <4>;
>>> + max-frequency = <50000000>;
>>> + cap-sd-highspeed;
>>> + cd-gpios = <&pio 261 0>;
>>> + vmmc-supply = <&mt6323_vmch_reg>;
>>> + vqmmc-supply = <&mt6323_vio18_reg>;
>>> +};
>>> +
>>> &pio {
>>> cir_pins_a:cir@0 {
>>> pins_cir {
>>> @@ -314,6 +340,17 @@
>>> bias-pull-down;
>>> drive-strength = <MTK_DRIVE_4mA>;
>>> };
>>> +
>>> + pins_wp {
>>> + pinmux = <MT7623_PIN_29_EINT7_FUNC_MSDC1_WP>;
>>> + input-enable;
>>> + bias-pull-up;
>>> + };
>>> +
>>> + pins_insert {
>>> + pinmux = <MT7623_PIN_261_MSDC1_INS_FUNC_GPIO261>;
>>> + bias-pull-up;
>>> + };
>>> };
>>> mmc1_pins_uhs: mmc1 {
>>
>>

\
 
 \ /
  Last update: 2017-08-14 17:19    [W:0.050 / U:0.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site